Application of the Resources Model to the Supervision of an Automated Process

The present study was designed to ascertain how far flagging up potential errors can improve the automatic interpretation of technical documents. We used the resources model to analyze the supervised retro-conversion of architectural floor plans from the perspective of distributed cognition. Results showed that automated assistance helps users to correct errors spotted by the system and saves time. Surprisingly, they also showed that flagging up possible errors may make users less effective in identifying and correcting errors that go unnoticed by the system. Responses to a questionnaire probing the participants’ confidence in the system suggested that they were so trusting that they lowered their vigilance in those areas that had not been signaled by the system, leading to the identification of fewer errors there. Thus, although the participants’ confidence in the automated assistance system led to improved performances in those areas it highlighted, it also meant that areas to which the system did not draw attention were less thoroughly checked.     

Through‐the‐glass spectroscopic ellipsometry for analysis of CdTe thin‐film solar cells in the superstrate configuration

Polycrystalline CdS/CdTe thin‐film solar cells in the superstrate configuration have been studied by spectroscopic ellipsometry (SE) using glass side illumination. In this measurement method, the first reflection from the ambient/glass interface is rejected, whereas the second reflection from the glass/film‐stack interface is collected; higher order reflections are also rejected. The SE analysis incorporates parameterized dielectric functions ε for solar cell component materials obtained by in situ and variable‐angle SE. In the SE analysis of the complete cells, a step‐wise procedure ranks the fitting parameters, including thicknesses and those defining the spectra in ε, according to their ability to reduce the root‐mean‐square deviation between the simulated and measured SE spectra. The best fit thicknesses from this analysis are found to be consistent with electron microscopy. Based on the SE results, the solar cell quantum efficiency (QE) can be simulated without any free parameters, and comparisons with measured QE enable optical model refinements as well as identification of optical and electronic losses. These capabilities have wide applications in photovoltaic module mapping and in‐line monitoring. Copyright © 2016 John Wiley & Sons, Ltd.     

CMOS inverters based positive type second generation current conveyor

A new versatile class AB low-voltage second generation current conveyor based on CMOS inverters operating in transconductance mode is presented in this letter. Against traditional design based on CCII+, the circuit is able to operate at low supply voltages and offers numerous advantages like class AB operation, large voltage and current swing, synthesis from digital inverters. Simulation results from a typical 0.35 μm CMOS process had demonstrated the circuit capability to operate at high frequency over wide voltage and wide current swings. The proposed circuit operation has been acted from measurements with the HEF4069UBP from Philips semiconductors [1].     

Complex permittivity characterization of benzocyclobutene for terahertz applications

High-quality polymers such as the benzocyclobutene polymer (BCB) provide interesting dielectric feature for terahertz applications. Already used in silicon integrated circuit technologies, this material could become one of the most promising candidates for the realization of future THz waveguides and interconnections on a silicon substrate but also after active devices process on the top of any other technology (GaAs, InP, GaN…). A frequency-dependent complex permittivity of spin-coated thick layers of this low-k dielectric is obtained from transmittance spectra measured with Fourier transform spectroscopy in the frequency range of 0.5-5.4 THz. The dielectric constant and the loss tangent are discussed according to curing conditions of the photosensitive resin used. A low loss tangent value of 7 − 9 × 10^-3 at 1 THz is obtained with polymerisation in oxygen-free atmosphere. An incomplete curing and a high dose UV exposure have a weak impact on losses. These results associated with the high compatibility of this polymer with silicon and metals make BCB layers well suited for the design of microelectronic THz devices and circuits.     

Grain morphology of Cu damascene lines

The evolution of the grain structure through annealing of narrow damascene Cu interconnects is important for any further design of highly integrated circuits. Here we present a comprehensive transmission electron microscopy study of damascene lines between 80 nm and 3000 nm wide. Experimental results clearly indicate that morphology evolutions through annealing are strongly influenced by the line width. If the lines are wider than 250 nm a strong connection between the grain structure within the lines and the overburden copper is present at least after sufficient annealing. Once the lines are as small as 80 nm the grain structure within the lines are only weakly connected to the overburden copper grown above.     

Multipath optimized link state routing for mobile ad hoc networks

Multipath routing protocols for Mobile Ad hoc NETwork (MANET) address the problem of scalability, security (confidentiality and integrity), lifetime of networks, instability of wireless transmissions, and their adaptation to applications.Our protocol, called MultiPath OLSR (MP-OLSR), is a multipath routing protocol based on OLSR [1]. The Multipath Dijkstra Algorithm is proposed to obtain multiple paths. The algorithm gains great flexibility and extensibility by employing different link metrics and cost functions. In addition, route recovery and loop detection are implemented in MP-OLSR in order to improve quality of service regarding OLSR. The backward compatibility with OLSR based on IP source routing is also studied. Simulation based on Qualnet simulator is performed in different scenarios. A testbed is also set up to validate the protocol in real world. The results reveal that MP-OLSR is suitable for mobile, large and dense networks with large traffic, and could satisfy critical multimedia applications with high on time constraints.     

Understanding of the annealing temperature impact on ion implanted bifacial n‐type solar cells to reach 20.3% efficiency

Ion implantation has the advantage of being a unidirectional doping technique. Unlike gaseous diffusion, this characteristic highlights strong possibilities to simplify solar cell process flows. The use of ion implantation doping for n‐type PERT bifacial solar cells is a promising process, but mainly if it goes with a unique co‐annealing step to activate both dopants and to grow a SiO₂ passivation layer. To develop this process and our SONIA cells, we studied the impact of the annealing temperature and that of the passivation layers on the electrical quality of the implanted B‐emitter and P‐BSF. A high annealing temperature (above 1000 °C) was necessary to fully activate the boron atoms and to anneal the implantation damages. Low J_0BSF (BSF contribution to the saturation current density) of 180 fA/cm² was reached at this high temperature with the best SiO₂ passivation layer. An average efficiency of 19.7% was reached using this simplified process flow (“co‐anneal process”) on large area (239 cm²) Cz solar cells. The efficiency was limited by a low FF, probably due to contaminations by metallization pastes. Improved performances were achieved in the case of a “separated anneals” process where the P‐BSF is activated at a lower temperature range. An average efficiency of 20.2% was obtained in this case, with a 20.3% certified cell. Copyright © 2014 John Wiley & Sons, Ltd.     

Optimized ITO-free tri-layer electrode for organic solar cells

The optical properties of ZnO/Ag/ZnO (ZAZ) multilayer structures were numerically modeled and calculated by a FDTD method. Such tri-layers were also manufactured using an ion beam sputtering plant. A good agreement is obtained between modelizations and realizations. The impact of the oxide thicknesses on the optical properties of the ZAZ structures were experimentally and numerically investigated, and allow us to adjust the spectral position of the transmission maximum. The transmission of these structures is optimized up to around 74%, on the whole absorption spectral range of the photoactive P3HT:PCBM bulk heterojunction. The best electrode design is glass/ZnO (30 nm)/Ag (14 nm)/ZnO (30 nm), which presents a sheet resistance of 7 Ω/□. The optimized ZAZ structure was successfully integrated in an organic solar cell as anode. A photovoltaic efficiency of 2.58% is obtained and is compared to an organic solar cell integrating a traditional ITO anode with an efficiency of 2.99%. Numerical calculations of the intrinsic absorption inside each layer of the organic solar cells are performed. Alternative ITO-free electrodes for organic solar cells are demonstrated.     

Analyse théorique d’un canal de propagation en présence de trajets multiples

Frequency representation of multipath fading on line-of-sight microwave paths is revisited together with a general point of view and with the aim of giving sound foundations of medium bandwidth modelling. Moreover some typical laws of variation of the selectivity according to the frequency and the hop length are derived.     

Statistiques de la fonction de transfert par trajets multiples pour des largeurs de bande moyennes. Application à la prévision de la qualité

It is shown, from data gathered on three different test links, that multipath transfer functions on a medium bandwidth can be modelled with three parameters. Moreover, the model parameters follow similar probability laws on the three links, thus leading to a universalstatistical model. This statistical model depends on two independent parameters. When the two statistical parameters are known, the outage time of the link can be deduced from the model. A first estimation of these parameters can be inferred from the distribution law of the levels at fixed frequency. The application of the method to two particular cases is presented.