Pulsed-current duty cycle dependence of electromigration-inducedstress generation in aluminum conductors

The effect of duty cycle of pulsed dc currents on the critical length-current density product, (jl_c), was measured using the Blech-Kinsbron edge-displacement technique [Thin Solid Films 25, 327 (1975)]. Unencapsulated Al edge-displacement segments mere stressed at various duty cycles and the critical lengths, the so-called “Blech lengths”, were measured. It was found that jl_c increased with decreasing duty cycle. We measured a factor of 2.6 increase in jl_c for the 25% duty cycle as compared to dc. This duty cycle dependence of Blech length implies that electromigration resistance for an integrated circuit would be increased for small duty cycle operation by increasing the fraction of interconnects which are sub-Blech-length and are not susceptible to EM damage     

Definition of the Linear Region of X-Ray -Induced Cable Response

Cable response to X-rays is linear with incident fluence, provided the deposited charge in cable dielectrics is directly proportional to the X-ray flux. To estimate the level at which the linear region ends, we discuss three nonlinear processes that modify the deposited charge profile in a hypothetical cable model: field-limiting in vacuum gaps, ionization effects in air-filled gaps, and radiation-induced dielectric conductivity. The exact level at which limiting of the Norton driver in an elemental length of cable begins depends on the cable geometry and the X-ray source. Estimates of the onset of nonlinearities caused by field-limiting and by dielectric conductivity are found in terms of cable and source parameters. With air-filled gaps, the Norton driver is always nonlinear. In addition to limiting of the Norton drivers, the load response of a long cable may be limited because propagating currents are attenuated by the induced conductivity of the bulk of the dielectric.     

Cooperative localization techniques for wireless sensor networks: free,signal and angle based techniques

This paper addresses the problem of localization in sensor networks where, initially, a certain number of sensors are aware of their positions (either by using GPS or by being hand‐placed) and are referred to as anchors. Our goal is to localize all sensors with high accuracy, while using a limited number of anchors. Sensors can be equipped with different technologies for signal and angle measurements. These measures can be altered by some errors because of the network environment that induces position inaccuracies. In this paper, we propose a family (AT‐Family) of three new distributed localization techniques in wireless sensor networks: free‐measurement (AT‐Free) where sensors have no capability of measure, signal‐measurement (AT‐Dist) where sensors can calculate distances, and angle‐measurement (AT‐Angle) where sensors can calculate angles. These methods determine the position of each sensor while indicating the accuracy of its position. They have two important properties: first, a sensor node can deduce if its estimated position is close to its real position and contribute to the positioning of others nodes; second, a sensor can eliminate wrong information received about its position. This last property allows to manage measure errors that are the main drawback of measure‐based methods such as AT‐Dist and AT‐Angle techniques. By varying the density and the error rate, simulations show that the three proposed techniques achieve good performances in term of high accuracy of localized nodes and less energy consuming while assuming presence of measure errors and considering low number of anchors. Copyright © 2012 John Wiley & Sons, Ltd.     

选择合适的无线技术(一):频谱、通信距离和网络拓扑

当今有许多不同的无线标准和协议在使用,要为任何特定的应用选择合适的技术可能很困难.在这篇文章中,我们将探讨一些需要考虑的关键标准,并评介四个流行的选项:Wi-Fi?技术(无线保真)、蓝牙低功耗(Bluetooth? Low Energy)技术、专有射频(RF)和来自连接性标准联盟(Connectivity Standa...     

Social media and political partisanship – A subaltern public sphere’s role in democracy

Social media, as a subaltern public sphere (Fraser, 1990), have a democratic function in providing an alternative platform for minorities and marginalized to defy mainstream discourses in the public sphere. However, social media have been found to have an echo chamber effect, which may be detrimental to democracy. They may help to accelerate the ascendancy of a “post-truth” era in which objective facts are less influential in shaping public opinion than appeals to emotion and personal belief. A study on political polarization, however, showed that selective exposure and avoidance in social media are weak indicators of polarization (Johnson et al., 2017). This study examines the role of social media in democracy and partisan politics. The authors considered that despite the echo chamber effect, social media have a limited part to play in the formation of polarized stances compared with other factors, such as demographics, political orientation, and mass media use. The study tested two main hypotheses: H1: Social media use is associated with political stance that is marginalized in the mainstream media; H2: Political orientation has a stronger relationship than social media use with the stance toward political values and social issues.The results supported both hypotheses. Social media are associated with political stance that is marginalized in the mainstream media. However, when compared with other factors, the relationship between social media and stance becomes less obvious. Although the echo chamber effect may reinforce the original stance, social media do not exhibit a strong relationship with the stance toward political values and social issues. Partisan orientation and use of partisan mass media are found to have stronger links with variations in stance. Social media, however, provide a subaltern public sphere for those excluded from the dominant public sphere, thus extending the public sphere to accommodate multiple opinions and perspectives.     

Microstructure and texture analysis of narrow copper line versus widths and annealing for reliability improvement

In this article, we focus on the possible influence of interconnect Cu microstructure on electromigration phenomenon. First three annealing conditions were applied on interconnects. Microstructure and texture of copper were characterized by Electron BackScattered Diffraction (EBSD). Then electromigration tests have been carried out on 70 and 150 nm line widths of 45 nm node technology. In both cases no significant difference was observed in term of reliability performance versus annealing conditions. On the contrary large difference is observed on Electron BackScattered Diffraction results. Then, a statistical approach was used to investigate local microstructure and texture of copper for 150 nm line width. The results underline that morphological parameters of copper can vary versus annealing conditions but lead to similar reliability performances. We can thus conclude that these parameters are not in relationship with electromigration phenomena in these interconnects. On the other hand, high amount of misorientation has been highlighted as responsible of early failures.     

Robotic ICSI (intracytoplasmic sperm injection)

This paper is the first report of robotic intracytoplasmic sperm injection (ICSI). ICSI is a clinical procedure performed worldwide in fertility clinics, requiring pick-up of a single sperm and insertion of it into an oocyte (i.e., egg cell). Since its invention 20 years ago, ICSI has been conducted manually by a handful of highly skilled embryologists; however, success rates vary significantly among clinics due to poor reproducibility and inconsistency across operators. We leverage our work in robotic cell injection to realize robotic ICSI and aim ultimately, to standardize how clinical ICSI is performed. This paper presents some of the technical aspects of our robotic ICSI system, including a cell holding device, motion control, and computer vision algorithms. The system performs visual tracking of single sperm, robotic immobilization of sperm, aspiration of sperm with picoliter volume, and insertion of sperm into an oocyte with a high degree of reproducibility. The system requires minimal human involvement (requiring only a few computer mouse clicks), and is human operator skill independent. Using the hamster oocyte-human sperm model in preliminary trials, the robotic system demonstrated a high success rate of 90.0% and survival rate of 90.7% (n=120).