Displacement control crack-growth instability in an elastic-softening material

The criterion for crack growth instability in an elastic-softening material that is subjected to displacement control loading conditions is examined. A theoretical analysis of the model of a solid containing two symmetrically situated deep cracks and with tensile loading of the remaining ligament, defines the criterion for crack growth instability. The criterion is expressed in terms of the material's softening characteristics and the solid's geometrical parameters. The analysis covers the complete spectrum of material behaviour from the case where the softening zone is very small to the case where instability does not occur until the softening zone traverses the ligament between the crack tips.     

“Metallisation” of oxide surfaces observed by in situ high-resolution electron microscopy

Intense irradiation (25–40 A/cm²) at intermediate energy (400 keV) has been found to cause “metallisation” of tungsten oxide and titanium niobate crystal surfaces. The possible mechanisms and the likely consequences for high-resolution imaging of clean oxide surfaces are briefly discussed.     

Three-Phase Induction Generator for Single-Phase Line

Hydroelectric generators of less than 20 kilowatts can be in remote areas served only by a single-phase line. For high efficiency and low cost, a three-phase induction generator should be used. This three-phase generator can operate with balanced voltages and currents when the ``phase-splitting' circuit uses two capacitors connetted to two different single-phase voltage sources.     

Accelerated aging of extruded dielectric power cables. I. Controland monitoring methodology

An improved accelerated cable life test is described. Through the use of programmable logic controllers (PLCs), very precise and consistent control of the accelerated aging process has been achieved. A computer has been utilized to make continuous real-time acquisition and storage of key operating parameters possible. This precise control and monitoring methodology has permitted the study of the synergistic effects of voltage and temperature on the accelerated aging of full-sized cables in the laboratory     

Organochlorine Contaminants of Wintering Ducks Foraging on Detroit River Sediments

Organochlorine analysis was performed on carcasses of 13 diving ducks from a 1981 wintering population that foraged on contaminated sediments in the lower Detroit River. Mean total PCB concentrations were 10 mg/kg for seven lesser scaups (Aythya affinis), 11 mg/kg for three greater scaups (A. marila), and 7.6 mg/kg for three goldeneyes (Bucephala clangula). Highest mean levels of other residues were measured for hexachlorobenzene (1.7 mg/kg) in goldeneyes, and transnonachlor (0.33 mg/kg) and 4,4’-DDE (1.3 mg/kg) in greater scaup. Quantitative analysis of 72 PCB congeners also was applied to water, seston, sediment, benthie oligochaetes, and carp from the same site. Principal congeners in most of the samples included some of the more toxic and persistent PCBs. Results of a multivariate analysis indicated that ratios of more conservative to less conservative PCBs did not vary significantly among ducks (α = .05), but differed from those in carp, oligochaetes, and sediment. For the February through March period of fat mobilization, concentrations of total PCB in lipid were inversely correlated with percent lipid (r = 0.76) in ducks. The percentage of conservative PCBs increased slightly. The distribution and partitioning of organochlorines, including toxic PCB congeners, varied considerably within this water column-sediment-fauna ecosystem. Estimates of toxic exposure based on total PCB values may be unreliable.     

Breaking the Nyquist barrier

The author discusses the concept that data sampled beyond the Nyquist frequency is meaningless. A simple signal processing scheme to extend resolution to nearly twice the Nyquist without the problem of alias emerged. It starts by placing one-dimensional signals into a simulated sample-and-hold process in a Mathcad application     

Effects of viscosity on the bitterness and astringency of grape seed tannin

To examine the separate effects of viscosity and sweetness on astringency, aqueous solutions of grape seed tannin (GST) were thickened with carboxymethyl cellulose (CMC) from 2 to 45 cP (experiment 1) or sweetened with 0 to 1.8 g/L aspartame (experiment 2). Trained subjects continuously rated astringency and bitterness in duplicate. Subjects were categorized by the salivary flow induced by citric acid and ability to taste n-propyl thiouracil (PROP). In experiment 1, maximum intensity and total duration of astringency were significantly decreased as viscosity rose, although time to maximum intensity of astringency was not affected. Maximum intensity and total duration of bitterness were not significantly affected by increasing viscosity; however, the onset of bitterness was significantly delayed. In experiment 2, increasing sweetness had no affect on any astringency parameter, although maximum intensity of bitterness was significantly decreased. Neither PROP nor salivary flow-status had any effect on perception of bitterness or astringency in either experiment.     

Control-canonical-form method applied to generating systems to improve dynamic stability characteristics

Contents The control-canonical-form (CCF) method is introduced for the purpose of applying it to high-order state-space single-input single or multiple-output (SISO or SIMO) and multiple-input multiple-output (MIMO) linear time-invariant system models to determine closed-loop systems (i.e. design robust controllers) from which enchanced dynamic stability characteristics and overall performance of these systems is achieved. The method has been applied successfully to a SISO 6th-order linearized state-space open-loop model (representing a simplified hydro power system), and to a MIMO 8th-order linearized state-space open-loop model (representing an 87.5 kVA synchronous machine with conventional exciter supplying power to an electric utility system through an interconnection network)

---

Anwendung der kanonischen Form der Zustandsrückführung auf Erzeugersysteme zur Verbesserung der dynamischen Stabilitätseigenschaften

Übersicht Die Methode der kanonischen Form wird auf lineare zeitinvariante Systeme höherer Ordnung im Zustandsraum angewendet, die eine oder mehrere Eingangsgrößen bei einer oder mehreren Ausgangsgrößen aufweisen. Damit werden robuste Regler entworfen, welche die dynamische Stabilität und das gesamte Betriebsverhalten verbessern. Die Methode wurde erfolgreich auf ein linearisiertes Modell sechster Ordnung mit einem Eingang und einem Ausgang angewendet, das vereinfachend eine Wasserkraftanlage darstellt; außerdem auf ein linearisiertes Zustandsmodell achter Ordnung einer Synchronmaschine 87,5kVA mit konventioneller Erregung, die über ein Verbindungsnetzwerk in das öffentliche Netz einspeist.