Recovering the observable part of the initial data of an infinite-dimensional linear system with skew-adjoint generator

We consider the problem of recovering the initial data (or initial state) of infinite-dimensional linear systems with unitary semigroups. It is well-known that this inverse problem is well posed if the system is exactly observable, but this assumption may be very restrictive in some applications. In this paper we are interested in systems which are not exactly observable, and in particular, where we cannot expect a full reconstruction. We propose to use the algorithm studied by Ramdani et al. in (Automatica 46:1616–1625, 2010) and prove that it always converges towards the observable part of the initial state. We give necessary and sufficient condition to have an exponential rate of convergence. Numerical simulations are presented to illustrate the theoretical results.     

Imaging with solid immersion lenses, spatial resolution, and applications

Solid immersion microscopy, similar to liquid immersion microscopy, extends the diffraction limit by filling the object space with a high refractive index material, such as glass (index of refraction n=1.5-2), sapphire (n/spl sim/1.8), and semiconductor materials (n/spl sim/3), which shrink the wavelength of light. But solid immersion technique can achieve significantly higher spatial resolution since the refractive indices of available solids can be much higher than those of liquids (n=1.3-1.5). Besides high spatial resolution, solid immersion microscopy also possesses all the good properties of far-field imaging, such as high transmission efficiency and parallel imaging capability, which make it outstanding among beyond-the-diffraction-limit optical imaging techniques. In this paper, we discuss, from an experimental point of view, the resolution limit of solid immersion microscopy and the implementation of such technique in various applications.     

Quantifying Thermal Spray Coating Architecture by Stereological Protocols: Part I. A Historical Perspective

This article presents, from a historical perspective, some stereological protocols of the first order. Such protocols can be implemented to quantify statistically the architecture of thermal spray coatings and their relevant features (pores, lamellas, etc.). A forthcoming Part II of this article will address some key points to implement, from a practical point of view, such protocols.

Application of External Axis in Robot-Assisted Thermal Spraying

Currently, industrial robots are widely used in the process of thermal spraying because of their high efficiency, security, and repeatability. Although robots are found suitable for use in industrial productions, they have some natural disadvantages because of their six-axis mechanical linkages. When a robot performs a series of stages of production, it could be hard to move from one to another because a few axes reach their limit value. For this reason, an external axis should be added to the robot system to extend the reachable space of the robots. This article concerns the application of external axis on ABB robots in thermal spraying and the different methods of off-line programming with external axis in the virtual environment. The developed software toolkit was applied to coat real workpiece with a complex geometry in atmospheric plasma spraying).     

Influence of Substrate Properties on the Formation of Suspension Plasma Sprayed Coatings

In this study, YSZ coatings were deposited on different substrate materials (stainless steel and aluminum) using suspension plasma spray technique. The effects of substrate properties (material, surface topology, temperature, and thickness) on the formation of coatings were investigated. The results showed that, with the identical spray parameters, the porosity is higher for the coatings deposited on aluminum than that on stainless steel due to the high thermal transfer ability of the former substrate material. The SEM results revealed that the microstructure of as-prepared coatings could be tailored from the vertical cracked structure to the columnar structure by increasing the substrate surface roughness and their formation mechanisms were discussed. The substrate preheating temperature has an influence on the microstructure of the coatings, especially in the interfacial region. Increasing the substrate temperature is an effective means for reducing the interface defects and for improving the adhesion of the coatings. With the increase in the substrate thickness, the quantity of the vertical cracks in the coatings is reduced and their width becomes narrower.     

Microstructural,mechanical and tribological properties of suspension plasma sprayed YSZ/h-BN composite coating

Brittleness, relative high friction coefficient and wear rate limit the applications of ceramic coatings as wear-resistant layers. However, because embedding additives with ceramic matrix has demonstrated to be an effective way to improve coating performances, different contents and size of h-BN were added into an YSZ suspension. Afterwards, the YSZ/h-BN composite coatings were manufactured by suspension plasma spray and their tribological analysis indicated that: i) the reduction of the friction coefficient and wear rate can be achieved by incorporating h-BN into YSZ coating. ii) finer h-BN particle is more helpful to enhance the tribological properties of the coating. iii) the optimum content is dependent on h-BN particle sizes. iv) when the contents and the size of the h-BN inclusion increase, the probability distribution of the micro-hardness can become bi-modal. Three worn surface conditions were summarized and their wear mechanisms were discussed as well.     

The Chemical Evolution of the La<Subscript>0.6</Subscript>Sr<Subscript>0.4</Subscript>CoO<Subscript>3−δ</Subscript> Surface Under SOFC Operating Conditions and Its Implications for Electrochemical Oxygen Exchange Activity

Owing to its extraordinary high activity for catalysing the oxygen exchange reaction, strontium doped LaCoO₃ (LSC) is one of the most promising materials for solid oxide fuel cell (SOFC) cathodes. However, under SOFC operating conditions this material suffers from performance degradation. This loss of electrochemical activity has been extensively studied in the past and an accumulation of strontium at the LSC surface has been shown to be responsible for most of the degradation effects. The present study sheds further light onto LSC surface changes also occurring under SOFC operating conditions. In-situ near ambient pressure X-ray photoelectron spectroscopy measurements were conducted at temperatures between 400 and 790 °C. Simultaneously, electrochemical impedance measurements were performed to characterise the catalytic activity of the LSC electrode surface for O₂ reduction. This combination allowed a correlation of the loss in electro-catalytic activity with the appearance of an additional La-containing Sr-oxide species at the LSC surface. This additional Sr-oxide species preferentially covers electrochemically active Co sites at the surface, and thus very effectively decreases the oxygen exchange performance of LSC. Formation of precipitates, in contrast, was found to play a less important role for the electrochemical degradation of LSC.     

Bubble and Froth Stabilizing Agents in Froth Flotation

The mineral processing industry relies heavily on froth flotation to beneficiate complex minerals. The performance of the process depends on a multitude of chemical reagents affecting the solid mineral particles as well as the air bubbles used to collect the valuable mineral particles. In flotation, bubbles and froths are transiently stable by the use of a frothing agent or the presence of inorganic electrolytes in the process water. This review presents the primary stages characterizing bubble coalescence. The effect of flotation reagents and inorganic electrolytes on the stability of bubbles and the mechanisms which delay the coalescence of bubbles are discussed. Recently it had been proposed that solid particles external to the flotation system may be intentionally added to stabilize the froth phase, which has attracted attention from the flotation community. This gave rise to additional studies on the topic. The final section of the paper was therefore designed to capture the progress made on this particular subject. The use of solid flotation aids offers a promising future to increase the recovery of valuable particles as these external particles may be customized. The advantage of solid particles over soluble reagents is that they may be recovered and re-used making them environmentally and economically attractive.     

Characterization of plutonium distribution in MIMAS MOX by image analysis

A better understanding of MOX fuel in-pile behaviour requires a very detailed characterization of the Pu distribution in the pellet before and after irradiation. Electron probe microanalysis (EPMA) can be used to determine the distributions of chemical elements with a spatial resolution of 1 μm. This paper describes the development of X-ray microanalysis techniques to produce semi-quantitative ‘maps’ of plutonium concentrations in order to rapidly characterize large areas of the fuel microstructure (1 mm²) with reasonable accuracy. A new segmentation technique based on statistical compatibility is then proposed, so as to finely describe the MIMAS MOX fuel microstructure. Two materials were finely characterized to demonstrate the reliability of this new method. In each case, the results demonstrate the good and reliable accuracy of this new characterization methodology. The analysis method used is currently able to identify three so-called phases (Pu-rich agglomerates, a coating phase and uranium-rich agglomerates), as well as to quantify the plutonium distribution and the plutonium content of these three phases. The impact of the fabrication process on the microstructure can be seen both in the surface distribution variations of the plutonium and in the local plutonium content variations.