A concise process technology for 3-D suspended radio frequency micro-inductors on silicon substrate

In this letter, a concise process technology is proposed for the first time to enable the fabrication of good quality three-dimensional (3-D) suspended radio frequency (RF) micro-inductors on bulk silicon, without utilizing the lithography process on sidewall and trench-bottom patterning. Samples were fabricated to demonstrate the applicability of the proposed process technology.     

Factors affecting cloud point analysis of palm oleins

Some of the factors affecting cloud point determination of palm oleins are described. These are the type of container used, method of stirring, rate of stirring and bath temperature. The repeatability and reproducibility standard deviations of the method are determined from collaborative trials. Recommendations for the test are made to reduce the large variations among laboratories.     

Effect of rotor profiles on the torque of a switched-reluctancemotor

The authors examine effects on the torque that simple variations of the standard rotor pole face profile could have, basically from an elementary viewpoint of how the modified profiles affect the distribution and magnitude of the radial and tangential components of the flux density. It is observed that the average torque is mostly affected by changes that alter the dominant radial component, such as changes in the effective air gap length. The other observation that an increase in the average torque can also be obtained by a favorable shift in the torque versus angle characteristics by relatively simple changes of the rotor pole profile is not so well known. Such a shift that reduces the slope of the torque angle characteristic, skewing the curve towards the unaligned position, has two advantages: one is that the phase inductance is at its maximum positive slop and, hence, the maximum torque, when the phase is energized; second, the flatter inductance profile near the aligned position when the phase current is to be commutated would allow a faster drop off of the commutated current and, thus, a smaller negative torque     

Effects of solid retention time on the performance of submerged anoxic/oxic membrane bioreactor.

In this study, four similar bench-scale submerged Anoxic/Oxic Membrane Bioreactors (MBR) were used simultaneously to investigate the effects of solids retention time (SRT) on organic and nitrogen removal in MBR for treating domestic wastewater. COD removal efficiencies in all reactors were consistently above 94% under steady state conditions. Complete conversion of NH(4+)-N to NO(3-)-N was readily achieved over a feed NH(4+)-N concentration range of 30 to 50 mg/L. It was also observed that SRT did not significantly affect the nitrification in the MBR systems investigated. The average denitrification efficiencies for the 3, 5, 10 and 20 days SRT operations were 43.9, 32.6, 47.5 and 66.5%, respectively. In general, the average effluent nitrogen concentrations, which were mainly nitrate, were about 22.2, 27.6, 21.7 and 13.9 mg/L for the 3, 5, 10 and 20 days SRT systems, respectively. The rate of membrane fouling at 3 days SRT operation was more rapid than that observed at 5 days SRT. No fouling was noted in the 10 days and 20 days SRT systems during the entire period of study.     

A knowledge-based system for sensor selection

This paper presents a Knowledge-based system (KBS) developed to allow users, who may not be knowledgeable about sensors, to select sensors suitable for their specific needs. The KBS runs on a micro-computer. The selection criteria are user specified and are based on the desired measurement parameters. The system output includes all of the operational and dimensional parameters of the recommended sensor, price, and vendor information.     

Analysis of MTF degradation in the imaging of cells in a flow system

The time-delay and integration method can be used with a charge-coupled device array to acquire images of cell in a flow cytometer. The loss of high spatial frequency components in images acquired with this technique is studied by deriving the modulation transfer function (MTF) for each of the main causes of image degradation: finite sampling aperture, nonsynchronism between image movement and charge transfer rate, discrete charge motion, transfer inefficiency, and axis misalignment. The system MTF and resolution in the horizontal and vertical directions are then examined.©1994 John Wiley & Sons Inc     

Closed form solution for the sensor registration problem using only position information

Sensors, mounted on the dexterous end of a robot, can be used for feedback control or calibration. When you mount a sensor on a robot it becomes necessary to find the pose (orientation and position) of the sensor relative to the robot. This is the sensor registration problem. Many researchers have provided closed-form solutions to the sensor registration problem; however, the published solutions apply only to sensors that can measure a complete pose (three positions and three orientations). Many sensors, however, can provide only position information; they cannot measure the orientation of an object. This article provides a closed-form solution to the sensor registration problem applicable when: (1) the sensor can provide only position information and (2) the robot can move along and rotate about straight lines. © 1994 John Wiley & Sons, Inc.     

Induced magnetic fields as evidence for subsurface oceans in Europa and Callisto

The Galileo spacecraft has been orbiting Jupiter since 7 December 1995, and encounters one of the four galilean satellites-Io, Europa, Ganymede and Callisto-on each orbit. Initial results from the spacecraft's magnetometer have indicated that neither Europa nor Callisto have an appreciable internal magnetic field, in contrast to Ganymede and possibly Io. Here we report perturbations of the external magnetic fields (associated with Jupiter's inner magnetosphere) in the vicinity of both Europa and Callisto. We interpret these perturbations as arising from induced magnetic fields, generated by the moons in response to the periodically varying plasma environment. Electromagnetic induction requires eddy currents to flow within the moons, and our calculations show that the most probable explanation is that there are layers of significant electrical conductivity just beneath the surfaces of both moons. We argue that these conducting layers may best be explained by the presence of salty liquid-water oceans, for which there is already indirect geological evidence in the case of Europa.     

Motor noise generation and prediction for high spinning speed hard disk drive

The acoustic level of a hard disk drive is an important specification. This is especially so for enterprise HDD which is required to operate under a high spinning speed. In order to reduce the acoustics level of a HDD, an in depth understanding behind the mechanisms whereby the noise is being generated in a HDD should be established. This paper will study the acoustics characteristics of a high speed permanent magnet brushless DC motor (PM BLDC) and investigate the physics underlying the generation of noise associated with a motor. An analysis procedure of the PM BLDC motor noise generating mechanisms is proposed. Through finite element analysis and experimental verification, the results indicate that the major noise source for the high speed PM BLDC motor is due to the presence of electromagnetic (EM) torque ripples. Furthermore, it has been observed that the noise radiated by a HDD can be amplified when its structural dynamics are close to the frequency components of the noise source. Finally, a methodology which discusses the steps involved in the prediction of motor radiated noise will be presented.