Gel chromism and anomalous luminescence in poly(3-alkylthiophene)

The absorption spectrum of poly(3-alkylthiophene) gel changes drastically in association with a volume instability upon changing the solvent composition and also the temperature. In the expanded state in chloroform and at high temperature, the photoluminescence is much enhanced compared with the shrunken state in ethanol and at low temperature. This gel chromism and anomalous luminescence are discussed in terms of the change of effective conjugation length induced by the steric hindrance and the dynamics of the photoexcited species.     

Some experimental findings in compression-after-impact (CAI) tests of CF/PEEK (APC-2) and conventional CF/epoxy flat plates

Compression-after-impact (CAI) tests have been conducted for quasi-isotropic thick plates with 48 plies by using the NASA method and on plates with 32 plies by using the SACMA method. Specimens are made of CF/PEEK (APC-2) and conventional CF/epoxy for the NASA plates and CF/epoxy for the SACMA plates. In the NASA CAI tests, the sequence of delamination buckling and its propagation is clearly revealed through various experimental techniques. One major technique is moiré topography, and the other is thermo-mechanical stress analysis with a high-accuracy infrared sensor. The arrest of delamination propagation just before catastrophic failure due to high fracture toughness is clearly captured by the moiré camera. This behavior provides good CAI values of CF/PEEK. The initial buckling properties of the delaminated region by the impact are then extensively discussed. Numerical predictions of initial buckling stress have been obtained by modelled geometry of the delaminated region simplified from its precise structure clarified by ultrasonic C-scanning. They agree fairly well with the experimental results. The in-plane stress distribution in the delaminated region before initial buckling is measured by an infrared stress graphic system. This compared favorably with finite element predictions. Two types of symmetric buckling modes with respect to the central plate surface, twin and single peak ones, are experimentally captured.     

Fabrication of blue-light emission fused-silica substrates by using Si-ion implantation and high-temperature annealing

We fabricated fused-silica substrates which emit blue light by using Si-ion implantation and high-temperature annealing. Photoluminescence peak wavelengths are around 400 nm, and the peak intensities can be remarkable after annealing above 1150 °C.     

An experimental BiCMOS video 10 bit ADC

The possibility of realizing a high-quality, low-power, and low-cost video 10 bit analog-to-digital converter is examined utilizing BiCMOS circuit and process technology. A single-power-supply, 10 bit 10 MHz operation, 500 mW power dissipation, and a 4.2×6.2 mm chip size with 4200 elements were obtained     

The structure of acetylene flames for diamond synthesis

An acetylene flame was photographed with an SIT camera through optical filters, and the signals were Abel transformed to obtain two-dimensional emission-intensity profiles. It was found that the intensive emissions of CH* and C*₂ are localized at the feather boundary, while the OH* emission is localized at the intermediate zone. The structure of the acetylene flame was made clear: it consists of a carbon-radical-rich feather and an oxygen-radical-rich intermediate zone. The carbon-radical concentrations are approximately in equilibrium near the burner exit while they decrease almost linearly via interdiffusion and reactions with the oxygen-radicals in the intermediate zone.Numerical simulations including detailed gaseous and surface reactions reproduced well previous preliminary calculations showing that CH₄ is rapidly produced in the boundary layer near the substrate followed by an increase in CH₃. This result satisfactorily explains the measured dependence of growth rate on the substrate temperature and ratio.     

Design of a Four-Element, Hollow-Cube Corner Retroreflector for Satellites by use of a Genetic Algorithm

A four-element retroreflector was designed for satellite laser ranging and Earth-satellite-Earth laser long-path absorption measurement of the atmosphere. The retroreflector consists of four symmetrically located corner retroreflectors. Each retroreflector element has curved mirrors and tuned dihedral angles to correct velocity aberrations. A genetic algorithm was employed to optimize dihedral angles of each element and the directions of the four elements. The optimized four-element retroreflector has high reflectance with a reasonably broad angular coverage. It is also shown that the genetic algorithm is effective for optimizing optics with many parameters.     

一种用于推挽式电压型逆变器的低损耗无源吸收电路

提出并实现了一种推挽式PWM电压型逆变器用无源吸收电路;设有独立的放电回路让缓冲电容器上的能量部分地回馈到直流电源中,高频放电能量不会叠加在输出电压上;缓冲电容器的电压被钳位,使得推挽电路特有的倍压不会在吸收电路上造成额外的损耗。给出吸收电路参数的设计准则和计算实例,在200VDC和30kW级的中压中功率逆变装置中发挥了推挽拓扑的优点。理论分析和实验验证了所提方法的有效性。     

Stress-corrosion cracking of aged AlCuMg alloys in NaCl solution

Pitting potentials and stress corrosion life-times of AlCuMg alloys (mainly 2024 alloy) with various ageing structures have been measured in a de-aerated 1M NaCl solution under conditions of controlled potential. The aged alloy, which has the higher susceptibility to stress-corrosion cracking, showed two pitting potentials corresponding to pitting at the grain boundaries and within the grains. The susceptibility of the alloys to intergranular stress-corrosion cracking occurred at potentials above the pitting potential of the grain boundaries. The intergranular stress-corrosion cracking is caused not by the dissolution of the grain boundary precipitates (S phase) but by the pitting dissolution of the solute-denuded zones along the grain boundaries. Aspects of SCC in the alloys are similar to those in the Al-4%Cu alloy without Mg.     

Determination of power reflectivity of quasi-graded distributedBragg reflectors using stopband width

The authors examine the reflectivity of the quasi-graded distributed Bragg reflector using the stopband width. The stopband width of about 1000 Å for a reflectivity of about 99% is able to be measured with an accuracy of ± 1 Å. Thus, the reflectivity is determined with high accuracy from the stopband width. It is found that the quasi-graded distributed Bragg reflector is a high-quality reflector with high reflectivity and low resistance     

A 1.5 V, 4.1 mW dual-channel audio delta-sigma D/A converter

The paper describes a stereo digital-to-analog converter intended for portable digital-audio which operates at 1.5 V and consumes only 4.1 mW. A 15-level quantization, third-order delta-sigma was employed to reduce digital operation speed, relax out-of-band filtering requirements, and enhance immunity to clock jitter. The use of direct charge transfer switched-capacitor technique in the multibit reconstruction DAC reduces kT/C noise and element mismatch without increase of power dissipation. The data weighted averaging algorithm suppresses nonlinearity caused by capacitor mismatch by first-order noise-shaping, thereby making mismatch-induced noise negligible. The stereo audio DAC achieves 90 dB dynamic range and 81 dB peak signal-to-noise-plus-distortion ratio over a 20 kHz passband. The 5.3 mm ² chip is fabricated in a 0.6 μm CMOS technology which includes low-threshold devices