Design and construction of a high temperature and pressure electrodeless conductivity probe

An electrodeless conductivity probe has been designed and tested at temperatures up to 250 degrees C and pressures of 4.13 MPa (600 psi). A unique pressure seal permits temperature cycling. Design of the electronics permits accurate measurement of conductivities at various elevated temperatures in spite of the change of magnetic properties of the toroids with temperature. The design of the probe can be adapted for insertion, in-line, or bypass operation.     

Studies of turn-off effects in power semiconductor devices

An analytical model has been developed for analyzing current and voltage transients during high power diode recovery. Using the charge control approach and approximating the excess charge distribution by simple geometrical curves a fast and convenient method for computer analysis is obtained. The model is thoroughly physical and makes use of the proper diode design parameters and the differential equations of the electrical network. There is no need for any experimental fitting parameter. All relevant complicating effects as emitter recombination, nonabrupt pn-junction and reverse current influence on the space-charge layer are considered. Comparisons between calculated and measured recovery behavior under several different conditions show good agreement and prove that the model may serve as a useful tool in device and circuit development including RC-snubber design. Furthermore, the calculated charge distribution varies during the recovery in a physically reasonable manner. Starting from measured recovery transients this model may also be used as a new method for determining the excess charge content in the diode at the beginning of the recovery phase.     

Discovery of an Allosteric Ligand Binding Site in SMYD3 Lysine Methyltransferase

SMYD3 is a multifunctional epigenetic enzyme with lysine methyltransferase activity and various interaction partners. It is implicated in the pathophysiology of cancers but with an unclear mechanism. To discover tool compounds for clarifying its biochemistry and potential as a therapeutic target, a set of drug-like compounds was screened in a biosensor-based competition assay. Diperodon was identified as an allosteric ligand; its R and S enantiomers were isolated, and their affinities to SMYD3 were determined (K_D=42 and 84 μM, respectively). Co-crystallization revealed that both enantiomers bind to a previously unidentified allosteric site in the C-terminal protein binding domain, consistent with its weak inhibitory effect. No competition between diperodon and HSP90 (a known SMYD3 interaction partner) was observed although SMYD3–HSP90 binding was confirmed (K_D=13 μM). Diperodon clearly represents a novel starting point for the design of tool compounds interacting with a druggable allosteric site, suitable for the exploration of noncatalytic SMYD3 functions and therapeutics with new mechanisms of action.     

Accuracy assessment of a mobile terrestrial lidar survey at Padre Island National Seashore

The higher point density and mobility of terrestrial laser scanning (light detection and ranging (lidar)) is desired when extremely detailed elevation data are needed for mapping vertically orientated complex features such as levees, dunes, and cliffs, or when highly accurate data are needed for monitoring geomorphic changes. Mobile terrestrial lidar scanners have the capability for rapid data collection on a larger spatial scale compared with tripod-based terrestrial lidar, but few studies have examined the accuracy of this relatively new mapping technology. For this reason, we conducted a field test at Padre Island National Seashore of a mobile lidar scanner mounted on a sport utility vehicle and integrated with a position and orientation system. The purpose of the study was to assess the vertical and horizontal accuracy of data collected by the mobile terrestrial lidar system, which is georeferenced to the Universal Transverse Mercator coordinate system and the North American Vertical Datum of 1988. To accomplish the study objectives, independent elevation data were collected by conducting a high-accuracy global positioning system survey to establish the coordinates and elevations of 12 targets spaced throughout the 12 km transect. These independent ground control data were compared to the lidar scanner-derived elevations to quantify the accuracy of the mobile lidar system. The performance of the mobile lidar system was also tested at various vehicle speeds and scan density settings (e.g. field of view and linear point spacing) to estimate the optimal parameters for desired point density. After adjustment of the lever arm parameters, the final point cloud accuracy was 0.060 m (east), 0.095 m (north), and 0.053 m (height). The very high density of the resulting point cloud was sufficient to map fine-scale topographic features, such as the complex shape of the sand dunes.     

Lidar-based mapping of flood control levees in South Louisiana

Flood protection in south Louisiana is largely dependent on earthen levees, and in the aftermath of Hurricane Katrina the state’s levee system has received intense scrutiny. Accurate elevation data along the levees are critical to local levee district managers responsible for monitoring and maintaining the extensive system of non-federal levees in coastal Louisiana. In 2012, high resolution airborne lidar data were acquired over levees in Lafourche Parish, Louisiana, and a mobile terrestrial lidar survey was conducted for selected levee segments using a terrestrial lidar scanner mounted on a truck. The mobile terrestrial lidar data were collected to test the feasibility of using this relatively new technology to map flood control levees and to compare the accuracy of the terrestrial and airborne lidar. Metrics assessing levee geometry derived from the two lidar surveys are also presented as an efficient, comprehensive method to quantify levee height and stability. The vertical root mean square error values of the terrestrial lidar and airborne lidar digital-derived digital terrain models were 0.038 m and 0.055 m, respectively. The comparison of levee metrics derived from the airborne and terrestrial lidar-based digital terrain models showed that both types of lidar yielded similar results, indicating that either or both surveying techniques could be used to monitor geomorphic change over time. Because airborne lidar is costly, many parts of the USA and other countries have never been mapped with airborne lidar, and repeat surveys are often not available for change detection studies. Terrestrial lidar provides a practical option for conducting repeat surveys of levees and other terrain features that cover a relatively small area, such as eroding cliffs or stream banks, and dunes.     

Preoperative functional magnetic resonance imaging (fMRI) of the motor system in patients with tumours in the parietal lobe

Intracranial lesions may compromise structures critical for motor performance, and mapping of the cortex, especially of the motor hand area, is important to reduce postoperative morbidity. We investigated nine patients with parietal lobe tumours and used functional MRI sensitized to changes in blood oxygenation to define the different motor areas, especially the primary sensorimotor cortex, in relation to the localization of the tumour. Activation was determined by pixel-by-pixel correlation of the signal intensity time course with a reference waveform equivalent to the stimulus protocol. All subjects showed significant activation of the primary sensorimotor cortex while performing a finger opposition task with the affected and unaffected side. In five patients the finger opposition task additionally activated the ipsilateral sensorimotor cortex and the supplementary motor area (SMA). Extension and flexion of the foot, additionally performed in two patients, also activated the sensorimotor cortex, in one case within the perifocal oedema of the tumour. Tumour localization near the central sulcus induced displacement of the sensorimotor cortex as compared to the unaffected side in all patients with a relevant mass effect. The results of our study demonstrate that functional MRI at 1.5 T with a clinically used tomograph can reproducibly localize critical brain regions in patients with intracranial lesions.     

EFFECT OF COMPOSITION ON PROPERTIES OF CONE 11 ZIRCONIUM SILICATE-OPACIFIED GLAZES *

Studies were made of the effects of magnesium, calcium, barium, strontium, and zinc oxides on the gloss, texture, and opacity of one-fire, zirconium silicate-opacified glazes at cone 11. The opacity was determined with a Hunter multipurpose reflectometer and the gloss was observed visually. Limits for the various fluxes were determined and a practical base glaze formula was developed.     

WET PROCESS ENAMELS FOR CAST IRON1

Wet process enameling of cast iron is becoming of importance because of its application to the enameling of stove parts, sanitary fittings and hardware. This paper is a report of an extended investigation of wet process enamels for cast iron, in connection with the use of a ground coat. Compositions used in dry process enameling have served as a basis for the work, which includes a study of ground coats and white cover enamels. The effect of varying methods of preparing the frits, mill additions, and the relation of composition of the enamels to such properties as adherence, texture and opacity have been carefully studied. Ground Coats. —Sintering of most ground coat frits has been found desirable in order to develop best adherence on the castings. Clay gave best results as a mill addition for the groundvt and feldspar were found to be less satisfactory. Excessive additions of clay or flint produced flaking of the ground coat while feldspar tended to develop blistering. About 15 per cent of clay or 10 per cent each of clay and flint are recommended as mill additions for the ground coats. Excessive additions of any one flux were not desirable, and best results were obtained when sodium, lead and boric oxides were combined in more or less definite pro-portions. Sodium oxide in excess of about 10 per cent gave rise to blistering. Boric oxide increased the firing range of the ground coats and was preferable to lead oxide on this account, although it tended to promote crawling of ground coats high in boric oxide if they were applied somewhat heavily. The best ground coats developed are Rg-26, 17, 1, 25 and 18. Cover Enamels. —Cover enamels were smelted in the usual manner. The mill additions consisted of 5 per cent of clay, 8 per cent of tin oxide, and 45 per cent of water, all based on the weight of the dry frit. For best results, the cover enamel must he adapted to the ground coat in refractoriness. Boric acid increased the firing range of the enamels but tended to promote crawling, although this was less pronounced in the case of the more fusible compositions. Boric oxide improved the opacity when suhsituted for such fluxes as sodium and lead oxides. Cryolite increased opacity but additions above 10 per cent, based on the melted weight, tended to promote crawling. Considering all factors, cover enamels R-14 11, 28, 1 and 18 gave best results.