Sigma-delta modulators operating at a limit cycle

A new type of sigma-delta modulator that operates in a special mode named limit-cycle mode (LCM) is proposed. In this mode, most of the SDM building blocks operate at a frequency that is an integer fraction of the applied sampling frequency. That brings several very attractive advantages: a reduction of the required power consumption per converted bandwidth, an immunity to excessive loop delays and to digital-analog converter waveform asymmetry and a higher tolerance to clock imperfections. The LCMs are studied via a graphical application of the describing function theory. A second-order continuous time SDM with 5 MHz conversion bandwidth, 1 GHz sampling frequency and 125 MHz limit-cycle frequency is used as a test case for the evaluation of the performance of the proposed type of modulators. High level and transistor simulations are presented and compared with the traditional SDM designs.     

Training and optimization of an artificial neural network controlling a hybrid power filter

A hybrid power compensator (HPC) consisting of a static VAr compensator and a dynamic compensator needs to be optimally controlled during the compensation of nonlinear loads. The HPC must be controlled to meet minimum requirements in terms of power factor and harmonic distortion, while at the same time minimizing its total cost. An artificial neural network (ANN) is used to control the HPC amidst a very dynamic power system environment. The performance of a reference ANN is evaluated while controlling an HPC connected to a typical nonlinear industrial load. The training and performance of the ANN is then optimized in terms of training set size, training set packing and ANN topology and the performance compared to the reference ANN. This paper highlights the importance of optimising the mentioned ANN parameters to achieve optimum ANN training and modeling accuracy. The results obtained reveals that the application of an ANN in controlling an HPC is feasible given that the ANN parameters are chosen appropriately.     

Recension des écrits sur l'impact des contacts sexuels précoces sur les hommes.

A review of the literature on the impact of sexual contacts between adults and boys reveals the existence of two principal outcomes: 1) some participants develop various disorders once in adulthood, such as behavioural problems, sexual disorders, or personality problems; 2) some participants do not present with any major disorders in the long run. These different outcomes may be associated with several moderating variables related to the sexual contacts, such as the level of coercion at the time of these contacts, the bond between the child and the adult, or the context of the sexual relation. However, the conclusions relating to the relations between early sexual contacts with adults and subsequent problems of adaptation in adulthood are difficult to determine. This is because of various methodological problems associated with relevant studies (i.e., definition of these contacts, nature of the sample, method evaluation, statistical analyses). In this article, we propose certain avenues of research that may help clarify this problem. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Influence of device engineering on the analog and RF performances of SOI MOSFETs

This work presents a systematic comparative study of the influence of various process options on the analog and RF properties of fully depleted (FD) silicon-on-insulator (SOI), partially depleted (PD) SOI, and bulk MOSFET's with gate lengths down to 0.08 /spl mu/m. We introduce the transconductance-over-drain current ratio and Early voltage as key figures of merits for the analog MOS performance and the gain and the transition and maximum frequencies for RF performances and link them to device engineering. Specifically, we investigate the effects of HALO implantation in FD, PD, and bulk devices, of film thickness in FD, of substrate doping in SOI, and of nonstandard channel engineering (i.e., asymmetric Graded-channel MOSFETs and gate-body contacted DTMOS).     

Desalination by distillation and by reverse osmosis — trends towards the future

As the requirement for fresh water increases worldwide, there is a need for more and more plants that are able to treat non-conventional water sources. Sea water has become an important source of fresh water in many arid regions. This feature provides an overview of recent process improvements in sea water desalination using reverse osmosis, multi-stage flash, multi-effect distillation and electrodialysis. Areas discussed include the use of alternative energy sources (wind energy, solar energy and nuclear energy) for reverse osmosis or distillation processes, and the impact of the different desalination process on the environment. Also covered are the implementation of hybrid processes in sea water desalination, and the pretreatment of desalination plants by pressure-driven membrane processes.     

Bio-layer management in anaerobic membrane bioreactors for wastewater treatment.

Membrane separation technology represents an alternative way to achieve biomass retention in anaerobic bioreactors for wastewater treatment. Due to high biomass concentrations of anaerobic reactors, cake formation is likely to represent a major cause of flux decline. In the presented research, experiments are performed on the effect of biomass concentration and level of gas sparging on the hydraulic capacity of a submerged anaerobic membrane bioreactor. Both parameters significantly affected the hydraulic capacity, with biomass exerting the most pronounced effect. After 50 days of continuous operation the critical flux remained virtually unchanged, despite an increase in membrane resistance, suggesting that biomass characteristics and hydraulic conditions determine the bio-layer formation rather than the membrane's fouling level. The concept of bio-layer management is introduced to describe the programmed combination of actions performed in order to control the formation of biomass layer over membranes.     

Synchronous Full-Scan for Asynchronous Handshake Circuits

Handshake circuits form a special class of asynchronous circuits that has enabled the industrial exploitation of the asynchronous potential such as low power, low electromagnetic emission, and increased cryptographic security. In this paper we present a test solution for handshake circuits that brings synchronous test-quality to asynchronous circuits. We add a synchronous mode of operation to handshake circuits that allows full controllability and observability during test. This technique is demonstrated on some industrial examples and gives over 99% stuck-at fault coverage, using test-pattern generators developed for synchronous circuits. The paper describes how such a full-scan mode can be achieved, including an approach to minimize the number of dummy latches in case latches are used in the data path of the handshake circuit.     

Reaction of cytochrome P450 with cumene hydroperoxide: ESR spin-trapping evidence for the homolytic scission of the peroxide O-O bond by ferric cytochrome P450 1A2

ESR spin trapping was used to investigate the reaction of rabbit cytochrome P450 (P450) 1A2 with cumene hydroperoxide. Cumene hydroperoxide-derived peroxyl, alkoxyl, and carbon-centered radicals were formed and trapped during the reaction. The relative contributions of each radical adduct to the composite ESR spectrum were influenced by the concentration of the spin trap. Computer simulation of the experimental data obtained at various 5,5-dimethyl-1-pyrroline N-oxide (DMPO) concentrations was used to quantitate the contributions of each radical adduct to the composite ESR spectrum. The alkoxyl radical was the initial radical produced during the reaction. Experiments with 2-methyl-2-nitrosopropane identified the carbon-centered adducts as those of the methyl radical, hydroxymethyl radical, and a secondary carbon-centered radical. The reaction did not require NADPH-cytochrome P450 reductase or NADPH. It is concluded that the reaction involves the initial homolytic scission of the peroxide O-O bond to produce the cumoxyl radical. Methyl radicals were produced from the beta-scission of the cumoxyl radical. The peroxyl adduct was not observed in the absence of molecular oxygen. We conclude that the DMPO peroxyl radical adduct detected in the presence of oxygen was due to the methylperoxyl radical formed by the reaction of the methyl radical with oxygen. At a higher P450 concentration, a protein-derived radical adduct was also detected.     

Clinical chemistry of common apolipoprotein E isoforms

Apolipoprotein E plays a central role in clearance of lipoprotein remnants by serving as a ligand for low-density lipoprotein and apolipoprotein E receptors. Three common alleles (apolipoprotein E(2), E(3) and E(4)) give rise to six phenotypes. Apolipoprotein E(3) is the ancestral form. Common apolipoprotein E isoforms derive from nucleotide substitutions in codons 112 and 158. Resulting cysteine-arginine substitutions cause differences in: affinities for low-density lipoprotein and apolipoprotein E receptors, low-density lipoprotein receptor activities, distribution of apolipoprotein E among lipoproteins, low-density lipoprotein formation rate, and cholesterol absorption. Accompanying changes in triglycerides, cholesterol and low-density lipoprotein may promote atherosclerosis development. Over 90% of patients with familial dysbetalipoproteinaemia have apolipoprotein E(2)/E(2). Apolipoprotein E(4) may promote atherosclerosis by its low-density lipoprotein raising effect. Establishment of apolipoprotein E isoforms may be important for patients with diabetes mellitus and several non-atherosclerotic diseases. Apolipoprotein E phenotyping exploits differences in isoelectric points. Isoelectric focusing uses gels that contain pH 4-7 ampholytes and urea. Serum is directly applied, or prepurified by delipidation, lipoprotein precipitation or dialysation. Isoelectric focusing is followed by immunofixation/protein staining. Another approach is electro- or diffusion blotting, followed by protein staining or immunological detection with anti-apolipoprotein E antibodies and an enzyme-conjugated second antibody. Apolipoprotein E genotyping demonstrates underlying point mutations. Analyses of polymerase chain reaction products are done by allele-specific oligonucleotide probes, restriction fragment length polymorphism, single-stranded conformational polymorphism, the primer-guided nucleotide incorporation assay, or denaturating gradient gel electrophoresis. Detection with primers that either or not initiate amplification is performed with the amplification refractory mutation system. Disparities between phenotyping and genotyping may derive from isoelectric focusing methods that do not adequately separate apolipoprotein E posttranslational variants, storage artifacts or faint isoelectric focusing bands.