Flashover voltage characteristics of contaminated station insulators under temporary ac overvoltages in the ac system connected with a frequency converter station

According to the recent analysis results of temporary ac overvoltage in the ac system connected with a frequency converter station, large-magnitude over-voltages were confirmed to occur under some special system conditions. Most of the station insulators currently used cannot withstand such overvoltages according to an evaluation based on the data obtained earlier. The necessity of tests to be done to evaluate such performance more accurately was recognized. Both power frequency and switching impulse overvoltage flashover tests were made on contaminated insulators by the method well simulating the natural wetting condition. Switching impulse flashover voltage with the waveshape having a long wavefront time of 2 ms can be well correlated with the flashover voltage characteristics of temporary ac overvoltage. Higher flashover voltage characteristics were obtained by a clean fog test method compared with those obtained by equivalent fog test method.     

A new method for power generation planning and problems of uncertainty

This paper presents a new method for power system planning which considers uncertainties of various system parameters as a part of the criterion function. The criterion function involves both the expected values of total system costs and the cost variances of different power plants. Previously, the authors proposed that these cost variances be evaluated from the existing power system plans in the form of the solutions to the inverse optimization problem, and then applied this procedure to the planning of power systems in Japan. However, because of the correlation between fuel and facility costs, the cost variances could not be determined as specific values. Here, to overcome this difficulty, the authors now introduce hydropower plants into the model as the so-called nonrisky elements and focus on the expenditure shares rather than the plant capacity shares. As a result, more reasonable results are obtained. This improved methodology is applied and the derived cost variances are shown. Further, using the resultant cost variances, the authors make Pareto-optimal power generation plans and demonstrate also the robustness of the method to price fluctuations.     

Some experimental findings in compression-after-impact (CAI) tests of CF/PEEK (APC-2) and conventional CF/epoxy flat plates

Compression-after-impact (CAI) tests have been conducted for quasi-isotropic thick plates with 48 plies by using the NASA method and on plates with 32 plies by using the SACMA method. Specimens are made of CF/PEEK (APC-2) and conventional CF/epoxy for the NASA plates and CF/epoxy for the SACMA plates. In the NASA CAI tests, the sequence of delamination buckling and its propagation is clearly revealed through various experimental techniques. One major technique is moiré topography, and the other is thermo-mechanical stress analysis with a high-accuracy infrared sensor. The arrest of delamination propagation just before catastrophic failure due to high fracture toughness is clearly captured by the moiré camera. This behavior provides good CAI values of CF/PEEK. The initial buckling properties of the delaminated region by the impact are then extensively discussed. Numerical predictions of initial buckling stress have been obtained by modelled geometry of the delaminated region simplified from its precise structure clarified by ultrasonic C-scanning. They agree fairly well with the experimental results. The in-plane stress distribution in the delaminated region before initial buckling is measured by an infrared stress graphic system. This compared favorably with finite element predictions. Two types of symmetric buckling modes with respect to the central plate surface, twin and single peak ones, are experimentally captured.     

Network formation and swelling behavior of photosensitive poly(vinyl alcohol) gels prepared by photogenerated crosslinking

Poly (vinyl alcohol) with pendent styrylpyridinium groups (SbQ) is insolubilized by photoirradiation. An association takes place in SbQ groups. The association of polymer chains becomes marked with increasing the number of SbQ groups. Mainly intermolecular crosslinks were formed. Transparent and homogeneous macrogels consisting of several intermolecular crosslinks are obtained. The proportion of the free water to the bound water in PVA-SbQ gels was 3.3?2.9 despite of the large change in conversion of photodimerization of SbQ groups, x=0.27?0.58. The water uptake after swelling of the gels in water increased 6–27 times compared to the original weight at pH=7. The higher the degree of photocrosslinking, the lower was the degree of swelling. The water diffusion coefficients, D, were (2.2?5.8) × 10^?5 cm² S^?1 for a 88% saponified PVA with 1 . 3 mol% SbQ groups. The volume of the gel increased discontinuously about 10-fold for the 99% saponified PVA with 0 . 096 mol% SbQ and 51% water (49% acetone). The acetone concentration at the transition decreased with increasing the degree of saponification of the PVA.     

Fabrication of aluminium foams from powder by hot extrusion and foaming

In order to produce aluminium foams for light-weight and energy absorbing structures of automobiles, a method for fabricating aluminium foam from powder mixed with a foaming agent by using a mould is proposed. The method consists of four sequential processes: powder compacting, extruding, foaming and moulding. In the experiment for fabricating aluminium foam from powder, the conditions of powder extrusion and foaming by the heated die are determined from the density of the aluminium foams made without a mould. The experimental results show that the relative density of the aluminium foam made under appropriate conditions is 0.22. In moulding of aluminium foam, a stainless steel pipe is used as a mould and the cylindrical aluminium foam is produced by filling into the pipe mould. The distribution of relative density within the aluminium foam bar is in a range of 0.2–0.3 by rapid cooling of the pipe. To examine the ratio of deformation energy to weight of the pipe including the aluminium foam, a compression test using a press is carried out. The deformation energy of the pipe can be increased with aluminium foam filled by the proposed method.     

A Unified Approach to Submicron DC MOS Transistor Modeling for Low-Voltage ICs

A unified single-equation approach for the MOS transistordrain current modeling for energy-efficient submicron MOS circuitsis presented. Instead of three sets of separate equations forthe triode, saturation, and weak inversion regions, only a continuousexpression which is valid to describe the behavior of drain currentand the derivatives in all operation regions can be realizedby using a combination of hyperbola, sigmoid, and interpolationmethods. The model expression can predict accurate results forthe current, output conductance, and transconductance with continuousand smooth characteristics. The simulation results agree wellwith experimental data.     

Dirac Cone Spin Polarization of Graphene by Magnetic Insulator Proximity Effect Probed with Outermost Surface Spin Spectroscopy

The effects of the proximity contact with magnetic insulator on the spin‐dependent electronic structure of graphene are explored for the heterostructure of single‐layer graphene (SLG) and yttrium iron garnet Y₃Fe₅O₁₂ (YIG) by means of outermost surface spin spectroscopy using a spin‐polarized metastable He atom beam. In the SLG/YIG heterostructure, the Dirac cone electrons of graphene are found to be negatively spin polarized in parallel to the minority spins of YIG with a large polarization degree, without giving rise to significant changes in the π band structure. Theoretical calculations reveal the electrostatic interfacial interactions providing a strong physical adhesion and the indirect exchange interaction causing the spin polarization of SLG at the interface with YIG. The Hall device of the SLG/YIG heterostructure exhibits a nonlinear Hall resistance attributable to the anomalous Hall effect, implying the extrinsic spin–orbit interactions as another manifestation of the proximity effect.     

Features of Rotating Stall Cell in a Diagonal Flow Fan（in Case of Mid-loading Rotor）

The structure and behavior of rotating stall cell were experimentally clarified in a diagonal flow fan. The specific-speed of the fan was 1140 (r/min, m3/min, m), and the total pressure-rise coefficient at design flow-rate was 0.345. The static pressure on outer casing wall and the total pressure at rotor inlet and outlet were measured using a high response pressure transducer. The measured data were processed by the use of DPLA technique, and the structure and behavior of rotating stall cell were obtained. As a result, the stall cell extent for circumferential and spanwise direction and the pressure distributions inside stall cell were clarified. The details of stall cell propagation were also shown.     

A 7 ns 1 Mb BiCMOS ECL SRAM with shift redundancy

A 7-Mb BiCMOS ECL (emitter coupled logic) SRAM was fabricated in a 0.8 μm BiCMOS process. An improved buffer with a high-level output of nearly V_CC is adopted to eliminate the DC current in the level converter circuit, and the PMOS transistor has a wide operating margin in the level converter. The configurable bit organization is realized by using a sense-amplifier switch circuit with no access degradation. A wired-OR demultiplexer for the ×1 output, having the same critical path as the ×4 output circuit, allows for the same access time between the two modes. The ×1 or ×4 mode is electrically selected by the external signal. A simplified programming redundancy technology, shift redundancy, is utilized. Address programming is performed by cutting only one fuse in the shift redundancy. The RAM operates at the ECL-10K level with an access time of 7 ns. and the power dissipation at 50 MHz is 600 mW for the × mode     

Low-Temperature Physical Properties of Ba8Ni x Ge46?x (x?=?3,?4,?6)

Polycrystalline samples of type?I clathrate Ba₈Ni _x Ge_46?x (x?=?3, 4, 6) have been synthesized using a radio-frequency (RF) induction furnace. Ba₈Ni _x Ge_46?x samples show metallic-like behavior (d??/dT?>?0) with high resistivity at room temperature, and diamagnetic susceptibility at 2?K and 300?K. The charge carriers vary from n type to p type depending on the Ni stoichiometry. The carrier concentrations at 300?K are calculated to be 5.84(3)?e^?/cell for x?=?3, 2.29(1)?e^?/cell for x?=?4, and 3.29(1)?h⁺/cell for x?=?6. The deviation of the carrier concentrations from the values expected based on 4-bonded Ni suggests that vacancies may play a very important role in the electronic states. The effective carrier masses are estimated from the low-temperature heat capacity data.