Structure−Activity Relationships of Cinnamate Ester Analogues as Potent Antiprotozoal Agents

Protozoal infections are still a global health problem, threatening the lives of millions of people around the world, mainly in impoverished tropical and sub-tropical regions. Thus, in view of the lack of efficient therapies and increasing resistances against existing drugs, this study describes the antiprotozoal potential of synthetic cinnamate ester analogues and their structure-activity relationships. In general, Leishmania donovani and Trypanosoma brucei were quite susceptible to the compounds in a structure-dependent manner. Detailed analysis revealed a key role of the substitution pattern on the aromatic ring and a marked effect of the side chain on the activity against these two parasites. The high antileishmanial potency and remarkable selectivity of the nitro-aromatic derivatives suggested them as promising candidates for further studies. On the other hand, the high in vitro potency of catechol-type compounds against T. brucei could not be extrapolated to an in vivo mouse model.     

Atomistic simulations of grain boundary migration in copper

While the motion of twist boundaries can be readily studied by atomistic simulations with molecular dynamics (MD) under the action of an elastic driving force, the approach fails for tilt boundaries. This is due to the interaction of the elastic stress with the grain boundary (GB) structure, which causes plastic strain by GB sliding. A novel concept, the orientation correlated driving force, is introduced to circumvent this problem. It is shown that this concept can be successfully applied to the study of the migration of tilt boundaries. The migration behavior of several twist and tilt GBs was investigated. The transition from low-to high-angle boundaries can be captured, and a structural transition of tilt boundaries was found at high temperatures, which also affected the migration behavior. The results compare well with experimental results of the motion high-angle boundaries, but for low-angle boundaries, the agreement is poor. This article is based on a presentation made in the “Hillert Symposium on Thermodynamics & Kinetics of Migrating Interfaces in Steels and Other Complex Alloys,” December 2–3, 2004, organized by The Royal Institute of Technology in Stockholm, Sweden.     

Sensor guided handling and assembly of active micro-systems

Positioning accuracies in the range of a few micrometers and below are necessary for the assembly of active micro-systems. In order to reach these accuracies, an assembly system for sensor guided micro-assembly is developed in the Collaborative Research Centre 516 “Design and manufacturing of active micro-systems”. The combination of a parallel robot with an integrated 3D vision sensor and a micro-gripper enables to reach relative positioning accuracies below 1 μm.     

Surfactant replacement therapy in acute respiratory distress syndrome from viral pneumonia

A modified natural surfactant was administered to a patient with life-threatening adult respiratory distress syndrome caused by viral pneumonia. Subsequently, there was a marked improvement in gas exchange. In order to assess the mechanism for improved oxygenation, computed tomography of the lungs was done. Quantitative analysis of the scans taken before and after surfactant administration indicates that improvement in gas exchange was largely due to the expansion of underinflated and collapsed lung areas. Although this is a single case report, it provides insight into the possible beneficial effect of instilled surfactant in severe respiratory distress from viral pneumonia.     

Growth Stresses in the Oxide Scales on TiAl Alloys at 800 and 900°C

In the oxidation of TiAl alloys, the role of scale-growth stresses formed during oxidation has, thus far, been unknown. In the present paper the oxide-growth stresses were investigated by the deflection-test method in monofacial oxidation (DTMO) accompanied by acoustic-emission measurements. On unmodified surfaces the growth stresses are compressive and reach levels of around –100 MPa. At the same time, significant acoustic emission occurs indicating that even under isothermal conditions, stresses are relieved by a scale-cracking mechanism. For oxide scales on TiAl surfaces, which had been ion implanted with chlorine before oxidation, a very thin protective alumina layer is formed which, however, develops growth stresses in the range of several GPa, accompanied by intensive acoustic emission. In all stress–time curves, a dynamic situation is observed. This consists of phases of stress relief by scale microcracking and phases of stresses increase due to crack healing and further oxide growth. As a result, the level of stress as a function of oxidation time, is characterized by an oscillating course.     

Finite constants: characterizations of a new decidable set of constants

Constant propagation, the replacement of program terms which represent a unique value at run time by their values, is a classical program optimization method. In spite of being treated for years, constant propagation still has been in the unsatisfactory phase of heuristics. We enhance the known constant propagation techniques to obtain an algorithm which is optimal for programs without loops. Fundamental is the introduction of a new decidable set of constants, the finite constants. This set has two different characterizations: a denotational one, which directly specifies our iterative algorithm and an operational one, which delivers the completeness or optimality of this algorithm for programs without loops. The algorithm is implemented in a commercial compiler project.     

Modellqualität als Indikator für Softwarequalität: eine Taxonomie

Zusammenfassung  Komplexit?t, Anforderungsmanagement und Variantenvielfalt sind zentrale Herausforderungen bei der Entwicklung und Evolution heutiger softwaregesteuerter Systeme. Diesen wird zunehmend durch den Einsatz modellbasierter Entwicklungsmethoden begegnet. Dadurch wird das Modell zum zentralen Artefakt und die Erstellung und Nutzung von Modellen zu einer zentralen T?tigkeit in der Softwareentwicklung. Mit der Bedeutung der Modelle steigen auch die Ansprüche an ihre Qualit?t. Dieser Beitrag untersucht die Implikationen, die daraus entstehen, insbesondere werden sinnvolle Qualit?tsmerkmale für softwarebeschreibende Modelle identifiziert und diskutiert.