Flexural properties of moldings of rigid polyurethane made by reaction injection molding

Flexural properties of moldings made by Reaction Injection Molding (RIM), which are structural foams consisting of high density skin and low density core, were investigated by three-point bending tests. Two failure modes were observed in bending tests of the moldings made by RIM, and they are classified as follows according to the density ratio of skin layer to core layer: the opposite side of the skin layer to which load was subjected failed by tensile stress: and the same side of the skin layer to which load was subjected failed by compressive stress, causing wrinkling or buckling. Then the conventional composite beam theory was applied to the former failure mode and Hoff s buckling theory to the latter, and equations were derived to predict the flexural properties of the structural foams, which involved buckling from the flexural properties of solid construction. In addition, it has been shown that there exists a density distribution that maximizes the flexural strength of the moldings made by RIM with a given overall density. The results obtained here should be useful to the optimum structural design of moldings made by RIM.     

Preparation and performance of poly(vinyl butyral) membrane for ultrafiltration

Ultrafiltration membrane was prepared from poly(vinyl butyral). The effects of membrane thickness, polymer concentration, evaporation time, and evaporation temperature, etc., on the performance of the resulting membranes have been studied. Dimethylacetamide was used as a casting solvent. The membrane formed by casting the polymer from a 15 wt % solution and evaporation at 25°C for 30 s had a flux value of 250 cm³ / cm² h (4.8 kg/cm², 26°C) at 92.9% rejection level for dextran sodium sulfate (average mol. wt. 550,000) separation. © 1993 John Wiley & Sons, Inc.     

Systematic analysis of glycosphingolipids in the human gastrointestinal tract: Enrichment of sulfatides with hydroxylated longer-chain fatty acids in the gastric and duodenal mucosa

The composition of the glycosphingolipids of the human gastrointestinal tract was studied. The major neutral glycosphingolipids were ceramide monohexosides (e.g., GalCer, GlcCer), LacCer, Gb₃Cer, Gb₄Cer and more polar ones with more than four sugars, whereas neither Gg₃Cer nor Gg₄Cer were present. The acidic glycosphingolipids consisted of sulfatides and gangliosides such as G_M3, G_M1, G_D3 and G_D1a. Also a large amount of sulfatides was found in the gastric mucosa and duodenum. The concentrations of sulfatides in the fundic mucosa, antral mucosa and duodenum amounted to 416.0, 933.8 and 682.9 nmol/g of dry weight, respectively, exceeding those in the gastric mucosa and kidney of other mammals. The major molecular species of the sulfatides were identified as I³SO₃-GalCer with hydroxylated longer-chain fatty acids based on the analyses by gas-liquid chromatography and negative ion fast-atom bombardment mass spectrometry. In contrast, gangliosides in these regions showed a tendency to be lower than sulfatides, and the molar ratios of sulfatides to gangliosides were about 2.0, whereas those in other parts were less than 0.5. A high content of sulfatides in the gastric and duodenal mucosa, where mucosa is easily insulted by acid, pepsin and bile salts, may be closely related to their roles in mucosal protection. The nomenclature used for gangliosides and other glycosphingolipids follows the system of Svennerholm (Ref. 1) and the recommendation of the IUPAC-IUB Commission (Ref. 2), respectively.     

Iodine reaction of vinyl acetate/vinyl propionate copolymers. III. Iodine affinities of the radically polymerized copolymers and the copolymers derived from partially saponified polyvinyl acetate

The minimum sequence lengths (n_c) of vinyl acetate (VAc) units necessary to form a colored iodine complex were determined to be 4 and 17 for radically polymerized VAc/vinyl propionate (VPr) and VAc/isopropenyl acetate (IPAc) copolymers, respectively. The iodine affinities (I/VAc) of VAc/VPr copolymers (SP-series) obtained by propionylation of partially saponified polyvinyl acetate (PVAc) were remarkably affected by the saponification conditions. An increase of the water content in acetone/water mixture as saponification solvent brought about a decrease of the iodine affinities of the SP-series. The dependence of the iodine affinity on the saponification of monomer units in the SP-series was compared with that in the radically polymerized VAc/VPr copolymers by taking the sequence probability as the measure of monomer unit distribution. The results strongly supported an occurence of the slide fastener reaction at high degrees of saponification, which was well-known in the saponification of PVAc. Furthermore, it was found that the saponification mode of PVAc at low degrees of saponification was influenced uniquely by the water content in saponification solvents and the saponification temperature.     

The effect of molybdate anion on the ion-selectivity of hydrous ferric oxide films in chloride solutions

The ion-selective property of hydrous ferric oxide precipitate films has been investigated by measuring membrane potentials which arise across precipitate membranes of hydrous ferric oxide with and without adsorbed MoO₄^2? ions and of ferric molybdate in solutions of NaCl, KCl, MgCl₂, CaCl₂, BaCl₂, AlCl₃, and FeCl₃. The hydrous ferric oxide membrane was only permeable to Cl^? ions in chloride solutions, whereas the membrane with adsorbed MoO₄^2? ions was permeable to cations in NaCl and KCl solutions, and to both Cl^? and cations in the presence of multivalent cations. The ferric molybdate membrane was permeable to Cl^? and cations in NaCl and KCl solutions, and only to Cl^? ions in the presence of multivalent cations. It is suggested that in chloride solutions, the corrosion of iron covered with a precipitate film of hydrous ferric oxide is accelerated by enrichment of Cl^? ions under the film, which may decrease the local pH and introduce a positive diffusion potential in the film. The adsorption of MoO₄^2? ions on the oxide changes the ion-selectivity of the precipitate film from the anion-selective to the cation-selective in solutions of NaCl and KCl. This cation-selectivity of the film may inhibit the corrosion of iron, because of H⁺ ions diffusing out of the film. The inhibitive effect of MoO₄^2? ions would be reduced in the presence of multivalent cations.