Ice-slurry production using direct contact heat transfer

An ice slurry generation system was developed using direct contact heat transfer between water and the coolant, Fluroinert FC-84. The location of the coolant nozzle is an important design consideration to avoid clogging due to freezing of water. An ice fraction of up to about 40 percent was obtained with the nozzle located at the bottom of the ice slurry tank and the jet directed upwards into the water. Two simplified model were developed to extract the heat transfer coefficient between the coolant drops and the water. The first model requires as input the average drop diameter and the residence time while the second model uses the measured drop diameter distribution. The estimated heat transfer coefficients are much smaller than those computed using single-sphere correlations.     

An Investigation on Noisy Environments in Evolutionary Multiobjective Optimization

In addition to satisfying several competing objectives, many real-world applications are also characterized by a certain degree of noise, manifesting itself in the form of signal distortion or uncertain information. In this paper, extensive studies are carried out to examine the impact of noisy environments in evolutionary multiobjective optimization. Three noise-handling features are then proposed based upon the analysis of empirical results, including an experiential learning directed perturbation operator that adapts the magnitude and direction of variation according to past experiences for fast convergence, a gene adaptation selection strategy that helps the evolutionary search in escaping from local optima or premature convergence, and a possibilistic archiving model based on the concept of possibility and necessity measures to deal with problem of uncertainties. In addition, the performances of various multiobjective evolutionary algorithms in noisy environments, as well as the robustness and effectiveness of the proposed features are examined based upon five benchmark problems characterized by different difficulties in local optimality, nonuniformity, discontinuity, and nonconvexity     

The effect of OPWF filler on impact strength of glass-fiber reinforced epoxy composite

In the present study, oil palm wood flour (OPWF) particles with less than 250 μm sizes have been used as filler materials in the woven-glass-fiber reinforced epoxy composite. The hybrid composites were fabricated using a hand lay-up method and cured at room temperature under a compressive load of 196 N (20 kg). The OPWF of 2.5 to 10 parts per hundred (pph) by weight was used to evaluate its effect on impact strength of the hybrid composites at a range of temperature from −50 to 50 °C. The impact strength, evaluated using V-notch Charpy method, showed reduction with increasing filler content up to 5 pph and then the strength increment in those composites containing more than 5 pph OPWF. More severe damages were found in specimens with higher filler contents resulting higher energy absorption during impact. The composites with a large amount of OPWF particles deflected crack propagation paths or created obstacles at the crack tips and increased toughness of the composites. The impact strength was found to decrease when the samples fractured at subzero temperatures and this happened because of the reduction of the matrix ductility at lower temperatures.     

Pile Response Adjacent to Braced Excavation

The excavation of soil for the construction of basements or cut-and-cover tunnels results in ground movements. One particular concern is that the excavation-induced lateral soil movements may adversely affect any nearby pile foundation. The lateral loads imposed by the soil movements induce bending moments and deflections in the pile, which may lead to structural distress and failure. This paper presents the results of an actual full-scale instrumented study that was carried to examine the behavior of an existing pile due to nearby excavation activities resulting from the construction of a 16 m deep cut-and-cover tunnel. The pile was located 3 m behind a 0.8 m thick diaphragm wall. Excavation to the formation level that was 16 m below the ground surface resulted in a maximum lateral pile movement of 28 mm. A simplified numerical procedure based on the finite-element method was used to analyze the pile response. Generally, the theoretical predictions were in reasonable agreement with the measured results.     

Design aspects of planar and conventional SMPS transformer: a cost benefit analysis

The intent of this paper is to design a high-frequency transformer that is to be incorporated into the DC/DC pulsewidth-modulated switch-mode power supplies by two different technical approaches: a conventional wound-coil magnetic using copper wires, and a planar magnetic with layered copper tracks on laminated printed circuit board. Comparisons will be made between the two approaches in terms of profile: mounting height and surface area, and performance: power losses and efficiency. Other indicators like temperature rise and leakage inductance that causes electromagnetic interference, and cost, materials, and process fluency are also to be looked into. A sandwiched configuration for primary and secondary windings is proposed for the planar type. Issues arising and typical phenomena encountered will be discussed in detail. Primarily, the dominating factor in performance, cost effectiveness, or circuit compactness that restrains the choice of a particular type is to be evaluated.     

Integrated-optic dispersion slope equalizer for N/spl times/ several tens of Gb/s WDM transmission

We report a dispersion slope equalizer on a planar lightwave circuit for wavelength division multiplexing (WDM) transmission. This device consists of an array of lattice-formed equalizers with different compensation values fabricated on one wafer and arrayed-waveguide gratings for wavelength multi/demultiplexing. We describe its configuration, operational principle, parameter design, fabrication, and measured characteristics in detail. N/spl times/20 and N/spl times/40 Gb/s slope equalizers were fabricated and their characteristics agreed well with designed values. We also report a reduction in the bias electrical power needed for thermooptic phase shifters in the equalizer array that we realized by employing a phase trimming technique normally used for optical switches.