Value of information in remanufacturing complex products

Remanufacturing facilities usually face a trade-off between limited information about remanufacturing yields and potentially long supplier lead times. To improve production performance, these firms may attempt to acquire more timely and accurate information about remanufacturing yields or alternatively, to reduce the lead times of purchased parts. We develop four decision-making models to evaluate the impact of yield information and supplier lead time on manufacturing costs. We identify the operating conditions under which these capabilities are valuable, along with their relative impact on facility performance. Each model is formulated as an infinite horizon, stochastic dynamic program (Markov decision process). Our results indicate that the yield information is generally quite valuable, while investments in supplier responsiveness provide trivial returns to products with few parts. However, as product complexity increases with large number of target parts, the value of short lead times increases.     

Application of novel extractants for actinide(III)/ lanthanide(III) separation in hollow-fibre modules

Separation tests using hollow-fibre modules were performed for the difficult selective extraction of trivalent actinides over fission lanthanides from acidic media. This article shows that with 2,6-di(5,6-dipropyl-1,2,4-triazin-3-yl)pyridine as the extractant, up to 94% americium could be extracted from 1.0 kmol/m³ HNO₃, with minimal lanthanide co-extraction. Using a synergistic mixture of bis(chlorophenyl)dithiophosphinic acid and tri-n-octyl phosphine oxide, tests were performed on extraction, lanthanide scrubbing and stripping. In the extraction test, up to 99.99% americium could be extracted from 0.5 kmol/m³ HNO₃, with approximately one third of the lanthanides being co-extracted. Mass transfer calculations using a consistent set of input data showed good agreement with the experiments.     

A comparison of CCS tandem overload controls

In this paper we analyse issues associated with overloads in tandem switching systems in Common Channel Signalling (CCS) networks. In particular, we examine the need for, and effectiveness of, Automatic Congestion Control (ACC), a CCS mechanism which allows a congested switching system to inform adjacent CCS nodes of its level of overload, and subsequently controls the rate at which traffic is sent to the congested node. We demonstrate the critical need for end-offices and tandem switching systems to implement some form of ACC if network performance is to be maintained during congestion, especially in tandem exchanges. In addition, we find that the presently defined ACC should be expanded to allow more levels of congestion to be reported to adjacent nodes, so that a more effective, finer grained control is produced.     

Mullite Formation by Endothermic Reaction of α-Alumina/Silica Microcomposite Particles

The formation of mullite was investigated using microcomposite powders which consist of α-alumina cores and amorphous silica coatings. Differential thermal analysis and X-ray diffraction showed that the mullitization reaction was endothermic. In contrast, mullite forms exothermically in samples prepared by sol-gel processing. The results are shown to be consistent with available thermodynamic data for mullite formation from different alumina and silica phases.     

Synthesis of heterocyclic metal complexes and their evaluation as marine antifoulants

4-Amino-3-thio-1,24-triazolidine (L₁) and 4-amino-5-thio-1,3,4-thiadiazole (L_II) as well as their metal complexes of the general formulae ML_I·2H₂O and ML_IICl (M; Pb(II), Cd(II) and Zn(II)) were prepared. With Sn(II), we obtained Sn(L_I)₂·2H₂O and SnL_IICl, respectively. The structures of the compounds were identified through elemental analysis, and IR and UV spectra measurements, in addition to thermal analysis in case of the metal complexes. The antifouling properties of the compounds were tested by their incorporation into paint formulations which were applied to PVC substrates and tested in water from Alexandria western harbour. When the compounds were added at 17·5% by volume, the coated panels were fouled after 3 months of immersion. The addition of 6·7% by volume of tributyltin oxide to 15·8% of the prepared compounds in one formulation elevated the paint efficiency and prevented fouling for 11 months. Paint containing solely tributyltin oxide at the same concentration was inactive against algae.     

A closer look at mutation in genetic algorithms

This paper examines the influence of mutation on the behavior of genetic algorithms through a series of examples and experiments. The results provide an existence proof that mutation is a far more profound operator than has ever been recognized. Implications are discussed which point to the importance of open questions concerning genetic algorithms. The paper also reviews the implementation of the infinite population model of Vose which forms the computational basis of this investigation.     

TRANSITIONAL OUTSOURCING

Midrange outsourcers offer small to midsize companies the advanced technologies employed by major corporations, with the added benefits of creative pricing strategies.     

A NEW CORPORATE ORDER Changing Priorities for IS

For the past three decades, IS managers have been faced with the tasks of honing their craft, improving productivity, and serving as the keepers of information technology for the corporation. For the most part, they have done a commendable job. However, the rules of the game are changing. Old solutions are no longer extensible to current problems, and today's problems are unlike any faced in the past. This article takes a fresh look at what the top priorities for IS managers should be in the coming years.     

Synthesis and properties of peroxy derivatives of epoxy resins based on Bisphenol A: Effects of the presence of boron trifluoride ethereate

Oligomers containing peroxy groups have been synthesized on the basis of epoxides reacting with tert–butylhydroperoxide in the presence of boron trifluoride etherate. Dependence of reaction rates upon the quantity of catalyst, temperature and also nature of hydroperoxide has been investigated: A kinetic equation for the process has been formulated and also a kinetic scheme for the reaction taking into account the presence of boron trifluoride etherate is proposed. Structures of the synthesized peroxy oligomers have been confirmed by IR- and NMR-spectroscopy. The reaction initiating properties of the oligomers so synthesized were studied using as the example the styrene polymerization reaction. Electronic Publication