Block size selection in rate-constrained geometry based point cloud compression

Multimedia Tools and Applications - In geometry-based point cloud compression, the geometry information is typically compressed using octree coding. In octree coding, the size of the blocks in the...     

Recent advances during CH4 dry reforming for syngas production: A mini review

Given the continuing issues of environment and energy, methane dry reforming for syngas production have sparked interest among researchers, but struggled with the process immaturity owing to catalyst deactivation. This review summarizes the recent advances in the development of efficient and stable catalysts with strong resistance to coking and metal sintering, including the application of novel materials, the assessment of advanced characterizations and the compatibility to improved reaction system. One feasible option is the crystalline oxide catalysts (perovskite, pyrochlore, spinel and LDHs), which feature a fine metal dispersion and surface confinement effect via a metal exsolution strategy and exhibit superior reactivity and stability. Some new materials (h-BN, clays and MOFs) also extend the option because of their unique morphology and microstructure. It also is elaborated that progresses were achieved in advanced characterizations application, leading to success in the establishment of reaction mechanisms and attributions to the formed robust catalysts. In addition, the perspective described the upgrade of reaction system to a higher reaction efficiency and milder reaction conditions. The combination of efficient reaction systems and robust catalysts paves a way for a scaling-up application of the process.     

MAX3100在80C196串口扩展中的应用

介绍采用新型的UART器件MAX3100为Intel单片机80C196扩展串口，给出了硬件设计和软件编程，并对关键技术进行了说明。     

采用不同模型预测低碳Fe–Ni合金等离子熔覆层的冲击韧性

采用等离子熔覆法在Mn13高锰钢上制备了低碳Fe-Ni合金层。以熔覆电流、喷头移动速率、离子气流量和热处理温度作为输入参数,以冲击韧性作为输出参数,建立了BP(误差反向传播)神经网络模型和粒子群算法优化(PSO)BP神经网络模型,并跟冲击韧性与热处理温度之间的线性回归模型进行对比。结果表明,线性回归模型、BP神经网络模型和PSO-BP模型的平均相对误差分别为7.06%、6.12%和3.03%。PSO-BP模型的预测结果与实测值的误差较小。     

Ti9Al合金的氢塑性效应

采用真空自耗电弧炉熔炼制备Ti9Al合金，通过渗氢处理显著提高氢含量，在凸轮塑性试验机ЧПИ-2上以10mm／min的速度进行热模拟试验。研究发现：氢可以降低Ti9Al合金的相变温度，扩大α β区的温度范围；氢作为卢稳定剂会妨碍或完全抑制以Ti3Al为基的α2相的析出；钛合金的氢合金化可促使卢相在更低温度下稳定化，明显地提高了Ti9Al合金塑性。     

PP/SBS/EVA三元共混改性制备汽车仪表板专用料的研究

聚丙烯（PP）由于具有价格低、原材料丰富、力学均衡性好、耐化学腐蚀等特点，近年来成为最热门的汽车零部件材料。本文以聚丙烯为基体树脂，热塑性丁苯橡胶（SBS）为主增韧剂，乙烯/醋酸乙烯共聚物（EVA）为辅助增韧剂，通过三无共混改性制备汽车仪有板专用料，并对改性的聚丙烯的材料的冲击强度、弯曲强度、弯曲模量、拉伸强度、断裂伸长率、收缩率、熔体流动速率进行测试。应用正交设计，确定了制备汽车仪表板专用料最佳配方。     

偶联剂对地砖用PVC填充材料相态结构和力学性能的影响

研究了钛酸酯类偶联剂和硅烷类偶联剂对钙矿、硅酸盐填充的PVC填允材料力学性能、相态结构、密度、热失重率及吸水伸长率和耐热阻燃性能的影响。结果表明,偶联剂可改善填充PVC的抗冲性能,降低其拉伸强度,扫描电镜分析表明,填料越细,分散越均匀,越易被PVC树脂所包覆,力学性能越好,研究得到了比重大、热失重率低、吸水伸长率小、阻燃耐烧灼性好的高填充PVC硬质塑料地板砖。     

等离子硅刻蚀及其工艺参数的多尺度优化

用CFD-ACE+和CFD-TOPO分别对容性耦合等离子体反应腔室放电和等离子硅刻蚀过程进行仿真,讨论不同射频电压和腔室条件对等离子体特性的影响.结果表明:随着射频电压的升高,离子的通量增大;在低射频电压时,离子通量随腔室压强的升高而减小,而在高射频电压时趋势则相反.用Kriging模型对影响刻蚀形貌的参数(腔室压强和射频电压)进行优化,结果表明该优化方法可以为工艺条件相近的刻蚀机设备的设计提供参考.     

对高职计算机基础教育的思考

分析了高职院校学生的特点和高职院校计算机基础教育存在的不足.联系"三元制"教育模式和协作学习理论,讨论了改善计算机基础教育的措施.