Synthesis of some new 3-(2′-heterocyclicethyl)-2-methyl-3,4-dihydroquinazolin-4-one derivatives as antimicrobial agents

3-(2′-Chloroethyl)-2-methyl-3,4-dihydroquinazolin-4-one was reacted with acetylacetone, ethyl acetoacetate and diethylmalonate in the presence of sodium ethoxide to afford the alkylation products IV, V and VI , Compounds IV, V and VI were reacted with hydrazine hydrate, phenylhydrazine, hydroxylamine hydrochloride, urea and thiourea to yield 3-(2′-heterocyclicethyl)-2-methyl-3,4-dihydroquinazolin-4-one derivatives VII-XV . The structures of the synthesized compounds were elucidated by elemental analyses and spectroscopic (IR and XH-NMR) analyses. The prepared compounds were tested for their antimicrobial activities in comparison with tetracycline as a reference compound.     

Morphology development in polyethylene/polystyrene blends: the influence of processing conditions and interfacial modification

The influence of processing conditions and interfacial modification on the morphology evolution and the composition range within which fully co‐continuous high density polyethylene/polystyrene blend structures can exist during blending in a single screw extruder was studied. Blends ranging from pure A to pure B component, with and without compatibilizer, were prepared under two different shear rates. It was found that high shear rates displaced the breakdown–coalescence balance of the dispersed nodules to the side of coalescence, narrowing the percolation domain and the critical composition for full co‐continuity decreased with increasing shear rates. The addition of a tri‐block compatibilizer induced the percolation threshold of the polystyrene phase to begin at lower percentages of polyethylene but the phase inversion point did not change. The experimental results are discussed in the light of various theoretical models. Copyright © 2005 Society of Chemical Industry     

Direct Instantaneous Torque Control in Direct Drive Permanent Magnet Synchronous Motors—a New Approach

In this paper, a novel direct instantaneous torque control scheme for a direct drive (DD) permanent magnet synchronous motor (PMSM) is presented. A hybrid control structure combining the internal model principle and the variable structure control (VSC) approach is proposed. First, a variable structure torque controller is adopted to regulate the torque angle increment according to the torque feedback error. Second, the appropriate control voltage vector is determined using the reference stator flux vector and the estimated dynamic back electromotive force (EMF) vector, as an internal model, in a deadbeat control manner. Subsequently, better disturbance rejection can be obtained with the proposed cascaded control structure. To robustly obtain the instantaneous torque and flux information, a robust adaptive motor model is proposed. The Lyapunov stability theory is used to analyze the stability of the augmented robust adaptive motor model and to give a guideline for tuning model parameters. Experimental results are presented to demonstrate the validity and effectiveness of the proposed instantaneous torque control scheme.     

Adaptive fuzzy fault-tolerant control using Nussbaum-type function with state-dependent actuator failures

Neural Computing and Applications - This paper presents an adaptive fuzzy fault-tolerant tracking control for a class of unknown multi-variable nonlinear systems, with external disturbances,...     

Effect of drop coalescence on mass transfer rate

Disperse-phase-controlled mass transfer rates from individual liquid drops suspended in a second liquid phase are measured optically immediately after the drop has been formed by coalescence of two smaller droplets. The net effect on mass transfer of the act of coalescence is determined by comparison to similar measurements made on the initial droplets in the absence of coalescence. The transfer rates immediately after coalescence are high rapidly fall to zero, rebound to an intermediate value and finally decay to the level expected for an undisturbed drop. The net effect on total mass transferred is detrimental in a clean system subject to interfacial instability but appears to be beneficial for contaminated systems or where no surface movements are spontaneously generated.     

Absolute Stability of Nonlinear Systems with Two Additive Time-varying Delay Components

In this paper, we present a new sufficient condition for absolute stability of Lure system with two additive time-varying delay components. This criterion is expressed as a set of linear matrix inequalities (LMIs), which can be readily tested by using standard numerical software. We use this new criterion to stabilize a class of nonlinear time-delay systems. Some numerical examples are given to illustrate the applicability of the results using standard numerical software.