Effect of low-pressure carburizing and plasma nitriding on mechanical properties and fatigue endurance limits of low alloy sintered steels

ABSTRACT

Thermochemical treatments like plasma nitriding or surface carburizing are commonly used to enhance surface hardness of steel components. An important difference between these treatments is the temperature at which they are carried out. In the present paper, the surface carburizing was carried out following a recently reported non-isothermal low pressure carburizing (LPC) treatment. In order to gain a comparative view of the effect of different treatments on the microstructure, microhardness, fatigue and impact properties, materials with distinct hardenability and widely used in the industrial production were evaluated. Tests were also carried out using industrially processed components aimed to an application demanding high wear resistance. The microstructural evolution during case hardening was studied by optical and electron microscopy.     

Micro-irrigation development in India: an analysis of distributional pattern and potential correlates

ABSTRACT

In India, of late, micro-irrigation has received considerable policy focus. However, as of 2017, only about 10% of the potential area is under micro-irrigation. The present study analyzes the pattern and equity issues of distribution of micro-irrigation in India and identifies the potential correlates. The regression analysis reveals that the stage of groundwater development and agro-climatic differences significantly influence the spread of micro-irrigation. The relatively low spread of micro-irrigation in states with over-exploited groundwater needs attention. Overall, the study points to the need to revamp the current micro-irrigation development programmes, which focus excessively on subsidy.     

A new cladding technology to bond aluminium on magnesium

ABSTRACT

An in situ hot press bonding technology has been developed to clad aluminium on magnesium. Followed by regular hot rolling, magnesium sheets, covered by ductile and corrosion-resistant aluminium without detectable oxides in the interface, are produced. The new technology requires no welding, vacuum, protective atmosphere or barrier layer, and it makes good interfacial strength and rollability. Aluminium–magnesium intermetallic phases are formed along the clad–core interface at elevated temperatures. They are not detrimental under compression but may cause clad-core delamination in tensile strain. However, the tensile failure is more dependent on the formability of magnesium core than on the strength of interface.     

Tunable passively Q-switched thulium doped fluoride fibre (TDFF) laser using reduced graphene oxide-silver (rGO-Ag) as saturable absorber

A tunable, passively Q-switched thulium doped fluoride fibre (TDFF) laser using a reduced-graphene oxide-silver (rGO-Ag) thin film as a saturable absorber (SA) for S band operation is proposed and its efficacy demonstrated. Over a pump power range of 91.4?mW up to 158.6?mW, passively generated Q-switched pulses are observed with repetition rates from 20 to 34.5?kHz and pulse widths from 3.1 to 7.1?µs. The highest pulse energy observed is 101.2?nJ with a signal to noise ratio of ～42?dB. The proposed laser has a tuning range ～52?nm from 1458 to 1510?nm with a tunable bandpass filter (TBPF) introduced into the cavity.     

The analysis for morphological evolution and crystallography of degenerate pearlite in 100Mn13 steel

During approximate 773 K aging treatment of 100Mn13 steel, degenerate pearlite will occur and evolve into lamellar pearlite during growth process. The microstructures of degenerate pearlite and its evolutionary lamellar pearlite are observed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results show that after 748 K, 773 K and 798 K aging, degenerate pearlites occur at grain boundary. At growth front of degenerate pearlite forming at 773 K and 798 K, pearlite presents a morphology of short lamellae of carbide and ferrite, indicating a trend of developing into lamellar pearlite. The higher the temperature is, the more obvious the trend is, and even a conventional lamellar pearlite has developed. However, there is no morphological evolution for degenerate pearlite forming at 748 K aging. Besides, the constituents of degenerate pearlite is identified as M₂₃C₆ and ferrite, and Kurdjumov-Sachs orientation relationship exists between them, (01 )_α//( 1 )_M23C6, [111]_α//[110]_M23C6. This orientation relationship maintains in morphological evolution from degenerate pearlite to lamellar pearlite.     

An evaluation of Acacia mearnsii tannin as an aluminum corrosion inhibitor in acid,alkaline, and neutral media

The electrochemical behavior of aluminum in tannin from Acacia mearnsii bark was evaluated by potentiodynamic polarization curves and electrochemical impedance spectroscopy (EIS) in media under three different pH conditions: acid, alkaline, and neutral. A relationship among pH, polymerization grade (PG), zeta potential, surface, and electrochemical properties was observed in the inhibition performance of the tannin. At high pH, the oligomer structure of the tannin was affected, resulting in a low PG (4) and high zeta potential (−75 mV), and consequently, the inhibition efficiency decreased (68%) in comparison with that in acid (99%) and neutral media (96%). The values obtained indicate a physisorption mechanism for the aluminum corrosion inhibition in the studied conditions.     

Effects of SiC particles codeposition and ultrasound agitation on the electrocrystallisation of nickel-based composite coatings

This study analysed the influence of the codeposition of SiC particles with different sizes: 50 nm, 500 nm and 5 μm, and the type of bath agitation (stirring or ultrasonic) on the electrocrystallisation of nickel coatings. The composites matrix microstructure was analysed by means of SEM, EBSD and XRD, to evaluate the grain size, crystal orientation, and internal stresses and was benchmarked against pure nickel samples electrodeposited in equivalent conditions. The codeposition of nano- and microsize particles with an approximate content of 0.8 and 4 vol.%, respectively, caused only a minor grain refinement and did not vary the dominant?<?100?>?crystal orientation observed in pure Ni. The internal stress was, however, increased by particles codeposition, up to 104 MPa by nanoparticles and 57 MPa by microparticles, compared to the values observed in pure nickel (41 MPa). The higher codeposition rate (11 vol.%) obtained by the addition of submicron-size particles caused a change in the grain growth from columnar to equiaxial, resulting in deposits with a fully random crystal orientation and pronounced grain refinement. The internal stress was also increased by 800% compared to pure nickel. The ultrasound (US) agitation during the deposition caused grain refinement and a selective particle inclusion prompting a decrease in the content of the particles with the larger particles. The deposits produced under US agitation showed an increase in the internal stresses, with double values compared to stirring. The increase in the deposits microhardness, from 280 HV in pure Ni to 560 HV in Ni/SiC submicron-US, was linked to the microstructural changes and particles content.

Graphical abstract