Lithium Tin Sulfide—a High‐Refractive‐Index 2D Material for Humidity‐Responsive Photonic Crystals

Extending the portfolio of novel stimuli‐responsive, high‐refractive‐index (RI) materials besides titania is key to improve the optical quality and sensing performance of existing photonic devices. Herein, lithium tin sulfide (LTS) nanosheets are introduced as a novel solution processable ultrahigh RI material (n = 2.50), which can be casted into homogeneous thin films using wet‐chemical deposition methods. Owing to its 2D morphology, thin films of LTS nanosheets are able to swell in response to changes of relative humidity. Integration of LTS nanosheets into Bragg stacks (BSs) based on TiO₂, SiO₂, nanoparticles or H₃Sb₃P₂O₁₄ nanosheets affords multilayer systems with high optical quality at an extremely low device thickness of below 1 µm. Owing to the ultrahigh RI of LTS nanosheets and the high transparency of the thin films, BSs based on porous titania as the low‐RI material are realized for the first time, showing potential application in light‐managing devices. Moreover, the highest RI contrast ever realized in BSs based on SiO₂ and LTS nanosheets is reported. Finally, exceptional swelling capability of an all‐nanosheet BS based on LTS and H₃Sb₃P₂O₁₄ nanosheets is demonstrated, which bodes well for a new generation of humidity sensors with extremely high sensitivity.     

Clustering‐based scheduling: A new class of scheduling algorithms for single‐hop lightwave networks

In wavelength division multiplexing (WDM) star networks, the construction of the transmission schedule is a key issue, which essentially affects the network performance. Up to now, classic scheduling techniques consider the nodes' requests in a sequential service order. However, these approaches are static and do not take into account the individual traffic pattern of each node. Owing to this major drawback, they suffer from low performance, especially when operating under asymmetric traffic. In this paper, a new class of scheduling algorithms for WDM star networks, which is based on the use of clustering techniques, is introduced. According to the proposed Clustering‐Based Scheduling Algorithm (CBSA), the network's nodes are organized into clusters, based on the number of their requests per channel. Then, their transmission priority is defined beginning from the nodes belonging to clusters with higher demands and ending to the nodes of clusters with fewer requests. The main objective of the proposed scheme is to minimize the length of the schedule by rearranging the nodes' service order. Furthermore, the proposed CBSA scheme adopts a prediction mechanism to minimize the computational complexity of the scheduling algorithm. Extensive simulation results are presented, which clearly indicate that the proposed approach leads to a significantly higher throughput‐delay performance when compared with conventional scheduling algorithms. We believe that the proposed clustering‐based approach can be the base of a new generation of high‐performance scheduling algorithms for WDM star networks. Copyright © 2008 John Wiley & Sons, Ltd.     

金属沾污对超薄栅氧(2. 5nm)特性的影响

采用可控的金属沾污程序 ,最大金属表面浓度控制在 10 1 2 cm- 2数量级 ,来模拟清洗工艺最大可能金属沾污表面浓度 .利用斜坡电流应力和栅注入方式测量本征电荷击穿来评估超薄栅氧特性和金属沾污效应 .研究了金属锆和钽沾污对超薄栅氧完整性的影响 .实验结果表明金属锆沾污对超薄栅氧完整性具有最严重危害 ;金属钽沾污的栅氧发生早期击穿现象 ,而金属铝沾污对超薄栅氧完整性没有明显影响 .     

An NMR‐MOUSE® for Analysis of Thin Objects

A special unilateral NMR sensor has been designed for investigations of thin samples with a thickness of less than 1 mm and of surface effects of polymers. For use with the bar‐magnet NMR‐MOUSE®, the so‐called “crazy coil” is introduced with a low penetration depth. It is a flat meander coil etched on a printed circuit board with wiggles in the conductors. The design of the new coil and FEM simulations of the B ₁ field are presented. Different applications are discussed by means of illustrative examples. They are the detection of surface damage in rubber samples, the swelling and drying of a latex membrane exposed to cyclohexane vapor mimicking a chemical sensor, and the drying of a thin sprayed adhesive layer.

Bar‐magnet NMR‐MOUSE® with crazy coil.     

Boride coatings obtained by pack cementation deposited on powder metallurgy and wrought Ti and Ti-6Al-4V

Wear resistance of Ti alloys needs to be improved, and an effective way to achieve this is through surface treatment. Boronizing is a surface treatment in which boron diffuses into the surface of Ti leading to the formation of hard and wear-resistant Ti borides. Boronizing of wrought and/or cast Ti alloys by pack cementation has been studied, while similar coatings on Ti alloys produced by powder metallurgy (PM) have not been reported. Also critical process parameters for boronizing Ti alloys, such as pack cementation powder composition and the process temperature have not been systematically studied and analysed. The present work reports on the surface modification of PM Ti and PM Ti-6Al-4V by boronizing, and presents some important thermodynamic aspects of the process comparing it with similar coatings applied to wrought Ti-6Al-4V. The coatings were characterised using scanning electron microscopy and X-ray diffraction. For both Ti and Ti-6Al-4V alloys the use of amorphous B as a B element supplier in the boriding powder pack led to the formation of a uniform external boride layer, while the use of B₄C as a B element supplier in the pack and under the same boronizing conditions, led to the formation of an external TiN layer and an internal layer containing B. The thermodynamic calculations performed proved successful in determining the appropriate conditions for boride coating deposition and estimating the phases likely to be formed. Finally the effect of surface roughness on the coating quality is discussed.