Temperature and pressure effects on supercritical CO2 extraction of tomato seed oil

Tomato seed oil was extracted with supercritical carbon dioxide in a semibatch-flow extractor within the temperature range 313–343 K and the pressure range 10.8–24.5MPa. The extraction rates increased with pressure, but decreased with temperature increase because of the variation in solvent density and resultant differences in oil solubility. The fatty acid composition of the extracted oil was similar to that of soybean oil.     

High-performance polymer alloys of polybenzoxazine and bismaleimide

Two series of high-performance polymer alloys were prepared by mixing typical benzoxine monomers, 3-phenyl-3,4-dihydro-2H-1,3-benzoxazine (P-a) or 6,6-(1-methylethyliden)-bis-(3,4-dihydro-3-phenyl-2H-1,3-benzoxazine) (B-a), with a typical bismaleimide, 4,4-bismaleimidodiphenyl methane by various ratios followed by thermal treatment up to 240 °C. DSC and IR of the alloys were examined to follow the curing reaction. These analyses showed that the obtained polymer alloys are AB co-cross-linked polymer networks through the formation of ether linkage between the hydroxyl group of polybenoxazine and the double bond of bismaleimide. Viscoelastic analysis and softening temperature measurement revealed that the polymer alloys have much higher glass transition temperatures than those of each homopolymer. The thermal stability also increased with the increase of bismaleimide content as evidenced by TGA.     

Properties of indium oxide/tin oxide multilayered films prepared by ion-beam sputtering

The preparation and characterization of indium oxide (InO _x )/tin oxide (SnO _y ) multilayered films deposited by ion-beam sputtering are described and compared with indium tin oxide (ITO) films. The structure and the optoelectrical properties of the films are studied in relation to the layered structures and the post-deposition annealing. Low-angle X-ray diffraction analysis showed that most films retained the regular layered structures even after annealing at 500° C for 16 h. As an example, we obtained a resistivity of 6×10^–4 cm and a transparency of about 85% in the visible range at a thickness of 110 nm in a multilayered film of InO _x (2.0 nm)/SnO _y (0.2 nm)×50 pairs when annealed at 300° C for 0.5 h in air. Hall coefficient measurements showed that this film had a mobility of 17 cm² V^–1 sec^–1 and a carrier concentration (electron density) of 5×10²⁰ cm^–3.     

Modification of mesophase pitch by blending Part 2 Modification of mesophase pitch fibre precursor with thermoresisting polyphenyleneoxide (PPO)

Polyphenyleneoxide was blended in amounts of 5 or 10 wt% into petroleum-derived mesophase pitch to reinforce the pitch fibre before the oxidative stabilization to achieve better handling properties. Although polyphenyleneoxide was fusible but hardly soluble in the mesophase pitch even at a spinning temperature of 350° C, blended pitch could be smoothly spun into pitch fibre 10m diameter, as could the parent pitch. Fibrous polyphenyleneoxide of less than 1m diameter was homogeneously dispersed in the pitch fibre, being arranged along the fibre axis. Such fibrous polyp henyleneoxide reinforced the pitch fibre considerably. The fibrous substances at the centre of the fibre disappeared in the carbonized fibre at 1300° C after oxidation at 250° C, although some short ones were observed in the skin region of the fibre, suggesting that polyphenyleneoxide was co-carbonized to be assimilated with mesophase pitch at the centre of the fibre, where the effects of oxidation may be rather limited. The oxidation reactivity and its mechanical strength after carbonization were slightly lower in comparison with those of the parent mesophase pitch.     

Adsorption of urea,creatinine, and uric acid from three solution types using spherical activated carbon and its recyclability

In this paper, we propose that the urinary toxins from the wastewater be adsorbed on an adsorbent such as spherical activated carbon and the latter be regenerated by subjecting it to high temperatures to recycle activated carbon and also to recycle the water used in dialysis. We studied the adsorption of artificial waste dialysate, which is a mixed solution of urea, creatinine, and uric acid, and the separate solutions for each of these and found that their extents of adsorption onto the spherical activated carbon material were nearly identical. The amount of adsorption was approximately 1.4 mg·g^-1 for urea, 18 mg·g^-1 for creatinine, and 20 mg·g^-1 for uric acid. The urea, creatinine, and uric acid adsorbed onto the spherical activated carbon decomposed on heat treatment at 500℃, and the adsorption capacity of the spherical activated carbon was regenerated. Our study successfully demonstrated that the spherical activated carbon can be recycled in the waste dialysate treatment process.     

Role of Acetic Acid Added to the Reaction Media for the Enantio-differentiating Hydrogenation of Methyl Acetoacetate Over a Tartaric Acid-modified Nickel Catalyst

The role of acetic acid added to the reaction media for the enantio-differentiating hydrogenation of methyl acetoacetate over a (R,R)-tartaric acid-in-situ-modified nickel catalyst was studied from the viewpoint of the hydrogenation rate during repeated runs. The hydrogenation of methyl acetoacetate on the “enantio-differentiating sites” of a tartaric acid-modified nickel catalyst was specifically accelerated by the acetic acid added to the reaction media to increase the enantio-differentiating ability of the catalyst. In order to increase the enantio-differentiating ability, the addition of acetic acid to the reaction media was required in each run during the repeated use of the catalyst.     

Rapid Quenching Technique Using Thermal-Image Furnace for Glass Preparation

A new technique combining a thermal-image furnace and a twin roller is described for quenching the melt to form glass. The technique was applied to the simple system Li₂O-SiO₂, since its fundamental parameters in the estimation of critical cooling rate are available. Glass flakes were obtained in the composition Li₄SiO₄, for which a very large critical cooling rate (∼10⁹ K·s⁻¹) was needed for glass formation.     

Enantio-differentiating hydrogenation of prochiral ketones over modified nickel

This article reviews the enantio-differentiating hydrogenation of prochiral ketones over a asymmetrically modified catalyst, focusing on the hydrogenation of simple prochiral alkanones. The parameters affecting catalytic activity and enantiodifferentiating ability are considerable in number, and each parameter should be optimized in order to attain a highperformance enantio-differentiating catalyst. Optimization of the parameters and the mode of enantio-differentiation are discussed and compared with the enantio-differentiating hydrogenation of β-ketoesters.     

Surface segregation of siloxane containing component in polysiloxane‐block‐polyimide and s‐BPDA/ODA polyimide blends

Surface segregation in polymer blend systems between 3,3′,4,4′‐biphenyltetracarboxylic dianhydride/4,4′‐diaminodiphenyl ether (s‐BPDA/ODA) polyimide and block copolymer based on polysiloxane‐block‐polyimide (SPI) has been investigated. These polyimide blends, having various compositions of the SPI, were processed by a solution casting method. The glass substrate used in the film‐casting process shows significant effect on the migration of surface segregated species to enrich the air‐exposed surface, whereas the more polar s‐BPDA/ODA tends to remain close to the polar glass substrate. X‐ray photoelectron spectroscopy reveals that even at low SPI concentration, the siloxane moieties in the block copolymer tend to segregate into the air side surface. Contact angle measurement evidently indicates an enrichment of the hydrophobic siloxane fraction on the blend film surface. The average water contact angle of glass side surface is 77°C whereas that of the air side is about 102°C in every blend ratio. This behavior confirms the surface segregation phase separation in these polymer blends. Finally, the surface morphology observed by atomic force microscopy also suggests segregation type of phase separation in these blend systems. POLYM. ENG. SCI., 47:489–498, 2007. © 2007 Society of Plastics Engineers.