Factors affecting the activity of anammox bacteria during start up in the continuous culture reactor.

Factors affecting cultivation of extremely slow-growing bacteria (anaerobic ammonium oxidiser, doubling time 11 days) were investigated by using upflow anaerobic sludge blanket (UASB) reactors which can maintain high solid retention time. The effects of concentrations of DO, free ammonia (FA), and nitrite on activation of anammox activity were tested during the start-up period. The reactor was inoculated with granular sludge collected from a full-scale UASB reactor used for treating brewery wastewater, and sludge from a piggery wastewater treatment plant and rotating biological contactor treating sewage. Results of continuous operation showed that concentrations of DO, free ammonia (FA) and nitrite in the reactors played a key role in stimulating the anammox activity during start-up period. It is crucial to keep DO below 0.2 ppm, FA below 2 mg/L and nitrite nitrogen below 35 mg/L to cultivate anammox cells in the continuous bioreactor. When the levels of DO, FA and nitrite in the influent were controlled at less than the inhibition levels, the anammox activity increased gradually in the anaerobic condition. Addition of hydrogen sulphide into the reactor enhanced anammox activity in the continuous culture. Through the SEM, TEM and FISH analysis, anammox bacteria were detected in the granular sludge after 3 months of continuous operation.     

Application of Code Approach for Emergency Evacuation in a Rail Station

This paper presents an emergency evacuation analysis during a mid-platform train fire in an underground rail station. A time-based evacuation scenario is developed taking into account the stairway inaccessibility due to smoke blockage. The calculation approach in NFPA 130 is then applied to a parametric study of this time-based scenario and its reliability is examined using a micro-simulation model. Both methods give consistent predictions of the exiting times. The results demonstrate that with the division of the station into two zones, the exiting time could not meet the code requirements, whereas it does meet the required exiting time without the division. Such division is due to smoke blockage and creates an uneven ratio of the occupant load to the available exiting capacity. This shows that appropriate consideration of the fire and smoke effects is important for station egress evaluation. Other issues such as the fire growth rate and the pre-evacuation time are also discussed.     

Damaged layer characteristics in micro-endmilling of copper using an ultrahigh-speed air spindle

This paper presents an investigation on the characteristics of damaged layer in micro-machining by using the ultrahigh-speed air spindle. The damaged layer in metal cutting is derived from plastic deformation and transformation of metal structure. In this study, micro-cutting force, surface roughness, and plastic deformation layer according to the variation of machining conditions were investigated by experiments. The damaged layer was measured using optical microscope for the samples prepared by metallographic techniques. Its scale was dependent on cutting process parameters, especially feed per tooth. According to experimental results, it was verified that the thickness of damaged layer was increased with increasing of feed per tooth and cutting depth, also thickness of damaged layer was reduced in down-milling compared to upmilling during micro-endmilling operation.     

ZJ510L-B汽车用高强度热轧板的试制

珠钢150t电弧炉-LF(VD)-CSP(紧凑式带材生产)流程试生产的5～8mm ZJ510L-B(0．16C--1．22Mn)汽车用高强度热轧板的铁素体晶粒尺寸为6．0～9．2μm，带状组织为1．5～2．5级，强度极限σb562～610MPa，延伸率δ5 32．0％～38．6％。文中还分析和提出了带状组织的形成原因和改进措施。     

Bias-temperature instabilities of polysilicon gate HfO/sub 2/ MOSFETs

Bias-temperature instabilities (BTI) of HfO/sub 2/ metal oxide semiconductor field effect transistors (MOSFETs) have been systematically studied for the first time. NMOS positive BTI (PBTI) exhibited a more significant V/sub t/ instability than that of PMOS negative BTI (NBTI), and limited the lifetime of HfO/sub 2/ MOSFETs. Although high-temperature forming gas annealing (HT-FGA) improved the interface quality by passivating the interfacial states with hydrogen, BTI behaviors were not strongly affected by the technique. Charge pumping measurements were extensively used to investigate the nature of the BTI degradation, and it was found that V/sub t/ degradation of NMOS PBTI was primarily caused by charge trapping in bulk HfO/sub 2/ rather than interfacial degradation. Deuterium (D/sub 2/) annealing was found to be an excellent technique to improve BTI immunity as well as to enhance the mobility of HfO/sub 2/ MOSFETs.     

基于多代理技术的传感器管理系统

针对分布式对空监视网中混合式传感器管理结构存在的问题，提出了基于多代理技术的混合式传感器管理结构。该结构较好地克服了混合式管理结构中在融合中心存在的瓶颈问题，通过多个传感器代理、融合中心代理之间的相互协商来实现传感器任务的分配。传感器代理与传感器相结合使传感器的工作模式实现高度的自动化和模块化，便于传感器的灵活组网。     

基于DSP+FPGA的扩频接收机快捕技术

提出一种在接收信号具有显著的多普勒频移的不确定性条件下,采用全数字的、适宜于扩频码和载波快速同步的新型扩频接收机结构。该接收机能在极短时间内建立快速同步,有效地实现实时突发通信。     

Viscous and Aeroelastic Effects on Wind Turbine Blades. The VISCEL project. Part I: 3D Navier–Stokes Rotor simulations

Aerodynamic modelling of HAWT rotors by means of “engineering methods” has reached a saddle point, where no further development can be expected without a breakthrough in understanding the physics of unsteady, rotating three‐dimensional flows. However, such a breakthrough becomes ever more necessary, as the size of the wind turbines increases. With the experimental work in that direction being mostly limited to observing the phenomena and interpreting the associated mechanisms, and its increased cost, alternatives are being sought. The use of CFD techniques and state‐of‐the‐art Navier–Stokes solvers is considered a very serious contender, a belief shared by the members of the present consortium, which has worked on the VISCEL JOR3‐CT98‐0208 Joule III project. This project's goal was to determine the aerodynamic characteristics as well as the aeroelastic behaviour of wind turbine blades across their broad range of operational conditions, from attached to highly separated flow regimes. The work programme included specific tasks for the validation and assessment of existing 3D solvers, for the parametric study of 3D flow around realistic blades and for the investigation of aeroelastic stability, at the blade section level. Copyright © 2003 John Wiley & Sons, Ltd.     

钢管打捆包装机的设计

为了提高包装质量，取代原人工打捆，设计开发了钢管打捆包装机，该包装机采用碾拉工艺，通过综合分析拉紧与绞纽组合动作的传动，实现了钢管的打捆包装机械化，使钢管包装质量达到了ISO9000标准要求，同时降低了劳动强度。