Impurity Effects on the Slippage of Nonsuperfluid Helium Films

We measured the mechanical response of ⁴ He films adsorbed on an oscillating substrate with a small amount of N₂ molecules using an ultrasonic technique. Compared with the substrate with no N₂ molecules, it was found that nonsuperfluid ⁴ He films undergo slipping at lower temperature. This means that the frictional force acting on these films is increased by N₂ molecules adsorbed on the substrate.     

Single molecule fluorescence autocorrelation measurement on anisotropic molecular diffusion in nematic liquid crystal

Diffusion kinetics of three dyes in nematic liquid crystals are studied with single-molecule fluorescence autocorrelation spectroscopy. Markedly large anisotropy was observed in the diffusion coefficient and structure of diffusion molecules showed no marked effect on the anisotropy.     

Fluorous Surface‐Active Distannoxane Catalysts

Fluorous distannoxanes (XR^f₂SnOSnR^f₂X)₂⋅n H₂O (R_f=C₆F₁₃C₂H₄) ( 1 : X=C₈F₁₇SO₃, n=10; 4 : X=Cl, n=0) ( 1 ) catalyze the Mukaiyama aldol reaction and the allylation of aldehydes with tetraallyltin at room temperature in fluorous/organic biphasic solvent systems, in which the reactions proceed more rapidly than in a single organic or fluorous solvent. Due to the unique surface activity of 1 , the catalyst, organic substrate(s), and reagent(s) are distributed in both organic and fluorous phases to facilitate smooth reactions. Upon dilution with toluene after the reaction, the catalyst concentrates to the fluorous phase, while the organic substances migrate to the organic phase to effect facile catalyst recovery and recycling. By virtue of such a unique solvophilicity, a new version of fluorous biphase technology has been developed.     

Acetylation of loofa (Luffa cylindrica) sponge as immobilization carrier for bioprocesses involving cellulase

The feasibility of using loofa sponge for immobilization of cellulase-producing microorganisms was investigated by acetylating loofa sponge. Acetylation was achieved by autoclaving process of loofa sponge immersed in acetic anhydride at various temperatures for various times. The degree of acetylation, as inferred by the weight percentage gain (WPG), was enhanced by increasing both temperature and the duration of acetylation. The acetylation of a piece of loofa sponge in an autoclave at 120 degrees C for 20 min resulted in a WPG of about 8%, which was sufficient to protect the loofa sponge against cellulose degradation. The acetylated loofa sponge prepared under this condition was not decomposed by commercial cellulase and its structure was maintained for more than 720 h during repeated-batch treatments with commercial cellulase. A flocculating yeast (Saccharomyces cerevisiae IR-2) and a fungus (Trichoderma reesei QM9414) were successfully immobilized in the acetylated loofa sponge. In each case, the percentage of immobilized cells was as high as that obtained using nonacetylated loofa sponge. Acetylation had no adverse effects on cell growth and immobilization of T. reesei QM9414, as well as on cell growth and ethanol production by S. cerevisiae IR-2. T. reesei QM9414 immobilized on an acetylated loofa sponge was successfully used for repeated-batch cellulase production from commercial cellulose powder. Although the acetylated loofa sponge showed a slight weight loss, it was not disintegrated by activated sludge. The results obtained in this study showed that acetylated loofa sponge is suitable as an immobilization carrier for bioprocesses involving cellulase.     

Refinement of inverter model considering dead‐time for performance improvement in predictive instantaneous current control

Model predictive instantaneous‐current control (MPIC), which was proposed in our earlier works, enables us to achieve better instantaneous current control using mathematical models of an inverter and permanent magnet synchronous motors (PMSMs). However, dead‐time to avoid short breakdown in the inverter is not usually considered in a general inverter model. Such an unmodeled part in the inverter model prevents accurate prediction of current evolution in motor systems based on the model predictive control. Therefore, in this paper, we analyze current response resulting from the dead‐time in the MPIC, and propose a refined inverter model considering the dead‐time so that control performance is improved. The effectiveness of the proposed method is verified through simulation and experiments. © 2013 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

In situ time-resolved X-ray diffraction of tobermorite formation in autoclaved aerated concrete: Influence of silica source reactivity and Al addition

The hydrothermal formation of tobermorite during the processing of autoclaved aerated concrete was investigated by in situ X-ray diffraction (XRD) analysis. High-energy X-rays from a synchrotron radiation source in combination with a newly developed autoclave cell and a photon-counting pixel array detector were used.To investigate the effects of the silica source, reactive quartz from chert and less-reactive quartz from quartz sand were used as starting materials. The effect of Al addition on tobermorite formation was also studied. In all cases, C-S-H, hydroxylellestadite and katoite were clearly observed as intermediates.Acceleration of tobermorite formation by Al addition was clearly observed. However, Al addition did not affect the dissolution rate of quartz. Two pathways, via C-S-H and katoite, were also observed in the Al-containing system. These results suggest that the structure of initially formed C-S-H is important for the subsequent tobermorite formation reactions.     

Control of carbon incorporation in AlAs grown by atomic layer epitaxy using variously orientated substrates

We demonstrate a method for successfully controlling carbon incorporation in AlAs layers grown by atomic layer epitaxy (ALE) using various GaAs substrates with different orientations. The number of alkyl radicals attached to an Al atom at the surface, which is a main factor in carbon incorporation, can be intentionally controlled by changing substrate orientation. We found that the carbon incorporation in ALE-AlAs using the (3 1 1)B surface is 2 x 10¹⁷,cm^-3, which is the lowest value ever reported for ALE-AlAs that satisfies one-monolayer self-limiting growth conditions.     

Correction and evaluation of the effect due to parasitic motion on primary accelerometer calibration

Primary accelerometer calibration is carried out under the assumption that a vibration exciter gives a rectilinear motion to an accelerometer to be calibrated. However practical vibration given by the vibration exciter includes parasitic motion such as transverse, rocking, and bending motion. Such parasitic motion would give two serious effects on primary calibration results, transverse motion effect and vibration distribution effect. Transverse motion effect is caused by an inner product of the vectors of both transverse motion and transverse sensitivity. On the other hand, the vibration distribution effect is caused by relative motion between a sensing point of accelerometer and a spot sensed by the interferometer. As these effects have close interaction between parasitic motion and measuring instruments, it would be very difficult to evaluate them by measuring independently each component.