Increase in photovoltaic performances of dye-sensitized solar cells—Modification of interface between TiO2 nano-porous layers and F-doped SnO2 layers

In order to improve the physical and chemical contacts between a porous TiO₂ layer and an F-doped SnO₂ transparent conductive layer (FTO), the surface of the FTO layer is polished. After polishing, the surface roughness decreased. However, light transmittance and sheet resistance did not vary largely. The short circuit current (J_sc) and efficiencies increased after the FTO was polished. It was found that the interfacial charge transfer between a TiO₂ layer and an FTO layer decreased by impedance measurement, which suggests that contacts between an FTO and a TiO₂ layer are improved because of the flatted surfaces or removal of electrical impurities. We propose one of the industrially important phenomena that surface polishing of FTO is one of the ways to increase photovoltaic performances for DSCs.     

Development of cube-type SOFC stacks using anode-supported tubular cells

Tubular SOFCs have shown many desirable characteristics such as high thermal stability during rapid heat cycling and large electrode area per unit volume, which can accelerate to realize SOFC systems applicable to portable devices and auxiliary power units for automobile. So far, we have developed anode-supported tubular SOFCs with 0.8–2 mm diameter using Gd-doped CeO₂ (GDC) electrolyte, NiO-GDC anode and (La, Sr)(Co, Fe)O₃ (LSCF)-GDC cathode. In this study, a newly developed cube-type SOFC stack which consists of three SOFC bundles was designed and examined. The bundle consists of three 2 mm diameter tubular SOFCs and a rectangular shaped cathode support where these tubular cells are arranged in parallel. The performance of the stack whose volume is less than 1 cm³ was shown to be 2.8 V OCV and over 1 W at 1.6 V under 500 °C. Cathode loss factor due to current collection from cathode matrix was also estimated using a proposed model.     

Japanese programs on novel concepts in PV

Japanese R&;D activities in photovoltaics (PV) and our R&;D activities with III-V compound multijunction (MJ) solar cells are presented. We have realized high-efficiency InGaP/InGaAs triple-junction solar cells with an efficiency of 36.5–37% (AM1.5G, 200 suns) and concentrator triple-junction solar cell modules with an outdoor efficiency of 27% as a result of designing a grid structure, developing low optical loss Fresnel lens and homogenizers, and designing low thermal conductivity modules. Our challenge now is to develop low-cost and high output power concentrator MJ solar cell modules with an output power of 400 W/m² for terrestrial applications.     

A 120-W Boost Converter Operation Using a High-Voltage GaN-HEMT

A boost converter with a 940-V/4.4 A GaN-HEMT as the main switching device was demonstrated to show the possibility of using high-voltage GaN-HEMTs in power electronic applications. The demonstrated circuit achieved an output power of 122 W and a power efficiency of 94.2% under a drain peak voltage as high as 350 V and a switching frequency of 1 MHz. The dual field-plate structure realized high-voltage switching operation with high power efficiency as dynamic on-resistance was suppressed by an increase of the current collapse phenomena.     

Morphological changes of Candida albicans induced by micafungin (FK463), a water-soluble echinocandin-like lipopeptide

Micafungin (FK463), a novel water-soluble echinocandin-like lipopeptide, exerted fungicidal action toward growing cells of Candida albicans at concentrations of 0.1 microg ml(-1) or above. The drug at these levels induced osmotically fragile cells and the resulting fungicidal effect was partially reversed when cultures were grown in the presence of an osmotic stabilizer. Candida cells incubated with fungicidal concentrations of micafungin gradually increased in size and/or became deformed. An electron microscopic study of such micafungin-treated cells revealed morphological alterations in the cell wall; deformation in contour, abnormal septum formation and decrease in thickness of the intermediate layer of the cell wall were prominent. In addition, the structure of cell membranes as well as of membranous cytoplasmic organelles was slightly impaired. These data suggest that micafungin principally affects the normal formation of the cell wall in growing Candida cells.     

A CMOS multichannel 10-Gb/s transceiver

We describe a CMOS multichannel transceiver that transmits and receives 10 Gb/s per channel over balanced copper media. The transceiver consists of two identical 10-Gb/s modules. Each module operates off a single 1.2-V supply and has a single 5-GHz phase-locked loop to supply a reference clock to two transmitter (Tx) channels and two receiver (Rx) channels. To track the input-signal phase, the Rx channel has a clock recovery unit (CRU), which uses a phase-interpolator-based timing generator and digital loop filter. The CRU can adjust the recovered clock phase with a resolution of 1.56 ps. Two sets of two-channel transceiver units were fabricated in 0.11-/spl mu/m CMOS on a single test chip. The transceiver unit size was 1.6 mm /spl times/ 2.6 mm. The Rx sensitivity was 120-mVp-p differential with a 70-ps phase margin for a common-mode voltage ranging from 0.6 to 1.0 V. The evaluated jitter tolerance curve met the OC-192 specification.     

Self‐consistent electrical parameter extraction from bias dependent spectral response measurements of III‐V multi‐junction solar cells

Spectral response of multi‐junction solar cell is complicated because of the interplay between external measurement conditions such as bias light intensity, monochromatic light intensity, bias voltage, and intrinsic electrical properties of series interconnected subcells. In this paper, we report an experimental study on the bias voltage‐dependent spectral response (SR) for multi‐junction solar cell. A self‐consistent iteration loop was developed from a nonlinear least square Powell hybrid algorithm that was used for curve fitting the experimental SR versus bias voltage data of each subcell. We demonstrated for the first time that this approach enabled us to derive the electrical parameters such as dark saturation currents (J₀), shunt resistance (R_sh), series resistance (R_s), and spectra response (J_photo) for each subcell of a Ga_0.99In_0.01As/Ge dual junction solar cell with stable convergence. The accuracies of the fitting results were confirmed by the agreement between the J–V curves calculated on the basis of these parameters and the experimental J–V curve of multi‐junction solar cell measured under AM1.5 and 1 sun condition. Copyright © 2013 John Wiley & Sons, Ltd.     

Finding module-based gene networks with state-space models - Mining high-dimensional and short time-course gene expression data

This study explores some problems to analyze time-course gene expression data by state-space models (SSMs). One problem is regarding the methods of parameter estimation and determination of the dimension of the internal state variable. Although several methods have been applied, there are few literature studies which with to compare them. Thus, this paper gives a brief review of the existing literature that use the SSM to analyze the gene expression time-course data. Another problem is the identifiability of the model. If the parameters of SSMs are simply estimated without any constraints for parameter space, they lack identifiability. To identify a system uniquely, it requires a specific algorithm to estimate the parameters with some constraints. For that purpose, an identifiable form of SSMs and an algorithm for estimating parameters are derived. The last problem is the extraction of biological information by interpreting the estimated parameters, such as mechanism of gene regulations at the module level. For that one, this paper explores methods to extract further information using the estimated parameters, that is, reconstruction of a module network from time-course gene expression data     

Criteria for versatile GaN MOVPE tool:high growth rate GaN by atmospheric pressure growth

Growth rate has a direct impact on the productivity of nitride LED production.Atmospheric pressure growth of GaN with a growth rate as high as 10μm/h and also Al_0.1Ga_0.9N growth of 1μm/h by using 4 inch by 11 production scale MOVPE are described.XRD of（002） and（102） direction was 200 arcsec and 250 arcsec, respectively.Impact of the growth rate on productivity is discussed.     

Image blurring of thick specimens due to MeV transmission electron scattering: a Monte Carlo study

Image blurring of MeV transmission electrons for gold nanoparticles on the top surface of micrometer-thick specimens has been investigated using the Monte Carlo simulation. Both the simulated line density profile and therefore image blurring were in good agreement with the experimental ones in the ultrahigh voltage electron microscope. Quantitative effects of specimen thickness and electron energy on image blurring were presented, in which the specimen thickness had a greater influence. Image blurring was demonstrated to be caused mainly by multiple elastic scattering, but it could be reduced to several nanometers for a 5?μm thick epoxy-resin specimen at the electron energy of 2?MeV.