Multi-walled carbon nanotube-reinforced copper nanocomposite coating fabricated by low-pressure cold spray process

Multi-walled carbon nanotube (MWCNT)-reinforced copper (Cu) nanocomposite coatings were successfully deposited on aluminum (Al) substrate by a cold spraying process at a low pressure. The microstructure and the Raman spectrum of the low-pressure-cold-sprayed MWCNT–Cu nanocomposite coating showed that the MWCNTs maintained their tube structure in the Cu matrix, even though structural damage to the MWCNTs increased slightly. MWCNT–Cu nanocomposite-coated Al exhibits higher thermal diffusivity than pure-Cu-coated Al with a comparable hardness. The higher thermal diffusivity of the MWCNT–Cu coating could be explained by the dispersion of MWCNTs within the clean and closed CNT/Cu interfaces, which were achieved with the aid of compressive stress during the cold spraying.     

In situ X-ray diffraction of surface oxide on type 430 stainless steel in breakaway condition using synchrotron radiation

Changes in the crystal structure of type 430 stainless steel and the oxides on its surface were studied in situ at 1373 K using a high-intensity synchrotron X-ray source provided by SPring-8 in Japan. The surface of the steel was initially covered with Cr₂O₃, which was then converted to FeCr₂O₄, and finally Fe₃O₄ and Fe₂O₃ formed on it. These results indicated that the reason for the breakaway oxidation in type 430 stainless steel is Cr depletion beneath Cr₂O₃ layer and the subsequent ionisation of Fe, not the simple mechanical failure of Cr₂O₃.     

Change in Oxygen Content of Y2O3-Nd2O3-Doped Silicon Nitride During Firing

The oxygen content of silicon nitride with 1 mol% Y₂O₃—Nd₂O₃ additive was measured after firing to determine the compositional change during gas-pressure sintering. Oxygen content decreases from 2.5 to 0.94 wt% during firing for 4 h at 1900°C and 10-MPa pressure in N₂. This decrease in oxygen results from the release of SiO gas generated by a thermaldecomposition reaction between Si₃N₄ and SiO₂. The resultant sintered silicon nitride material contains less than 1 wt% oxygen.     

Pervaporation separation of water/ethanol mixtures through polysaccharide membranes. II. The permselectivity of chitosan membrane

The separation of water/alcohol mixtures through chitosan membrane was investigated. The degree of the deacetylation of chitosan did not affect the selectivity of the membrane in the separation of the water/ethanol mixture. The selectivity of the chitosan membrane was affected by the specific salts such as CoSO₄, ZnSO₄, and MnSO₄ and it increased when the salts were present in the feed mixture or the membrane was pretreated with the salt solution. This behavior would be explained by the contraction of the “holes” produced by the thermal motion of polymer chains and this contraction would be correlated with the conformation change of chitosan molecule due to the formation of complexes with metal ions.     

Synthesis of a photoimmobilizable histidine polymer for surface modification

A novel photoreactive polymer with histidine polar groups was synthesized through the copolymerization of two types of methacrylic acid, one carrying histidine groups and the other carrying azidoaniline groups. The polymer was photoimmobilized on polyester disks for surface modification. The effect of the surface modification on the hydrophilic and biofouling properties was investigated. Static contact angle measurements showed that the polymeric surface was modified to be comparatively hydrophilic in the polymer‐immobilized region. Micropattern immobilization was carried out with a photolithographic method. Atomic force microscopy measurements showed that the polymer was formed on the disks in response to ultraviolet irradiation. Protein adsorption was reduced on the polymer‐immobilized regions, and in those regions, spreading and adhesion of mammalian cells were reduced in comparison with that in nonimmobilized regions. In conclusion, a novel histidine‐containing polymer was photoreactively immobilized on a conventional polymer surface, and it had reduced interaction with proteins and cells. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

High Resistance of Cu–Ferrierite to Coke Formation During NH3-SCR in the Presence of n-Decane

Selective catalytic reduction of NO _x by NH₃ over Cu–FER and Cu–ZSM-5 in the presence of n-decane and SO₂ was investigated. NO _x conversion over Cu–ZSM-5 decreased in the presence of n-decane, owing to inhibition of the active sites by coke formation. In contrast, coke formation was negligible over Cu–FER, which maintained its NO _x conversion activity even in the presence of decane. Coke formation was negligible over H–ZSM-5 and H–FER supports, which suggests that Cu species were involved in coke formation. Temperature-programmed reduction by H₂ and electron spin resonance spectroscopy indicated that [Cu–O–Cu]²⁺ was probably the Cu species involved in coke formation over Cu–ZSM-5.     

Preparation and photocatalytic activity of Keggin-ion tungstate and TiO2 hybrid layer-by-layer film composites

Keggin ions (PW₁₂O₄₀³⁻ (PW₁₂), SiW₁₂O₄₀⁴⁻ (SiW₁₂), H₂W₁₂O₄₀⁶⁻ (H₂W₁₂)) and TiO₂ hybrid thin films were prepared using the layer-by-layer method. Their photocatalytic activities were investigated using gaseous 2-propanol decomposition. All films were transparent in the visible wavelength range. For 2-propanol decomposition, H₂W₁₂ was the most effective for the combination with TiO₂ despite having the smallest TiO₂ deposition amount. The photocatalytic activity of the PW₁₂–TiO₂ hybrid film was increased 2.3 times by visible light with UV illumination. This increase was less remarkable for hybrid films of other Keggin ions, suggesting that the visible light excitation of reduced PW₁₂ plays an important role in the enhancement of 2-propanol decomposition.     

An Improved Method for Preparing Dimethyl Disulfide Adducts for GC/MS Analysis

Dimethyl disulfide (DMDS) adducts are prepared from fatty acid methyl esters to locate the double-bond position in monoenoic fatty acids by gas chromatography/mass spectrometry. We improved our original procedure for preparing DMDS adducts with a simple device that can be made in any laboratory using a glass pipette and silica based packing material, Extelut NT.     

The alkylation of biphenyl over three-dimensional large pore zeolites: The influence of zeolite structure and alkylating agent on the selectivity for 4,4′-dialkylbiphenyl

Catalytic properties of three-dimensional zeolites, Y (FAU), Beta (BEA), and CIT-1 (CON) zeolites were examined in the alkylation, isopropylation, sec-butylation, and tert-butylation, of biphenyl (BP), and compared to those of H-mordenite (MOR). The selectivities for 4,4′-dialkylbiphenyl (4,4′-DABP) varied with the types of zeolite and of alkylating agent. FAU, BEA, and CON gave only low selectivities for 4,4′-diisopropylbiphenyl (4,4′-DIPB) in the isopropylation, and predominant isomers were bulky and thermodynamically unstable 2,x′-DIPB (2,2′-, 2,3′-, and 2,4′-) at lower temperatures, and bulky and thermodynamically stable 3,4′- and 3,3′-DIPB at higher temperatures: this is quite different from catalytic features over MOR, which gave 4,4′-DIPB with high selectivities at moderate temperatures. These results suggest that FAU, BEA, and CON have no shape-selective nature in the isopropylation, and that the reaction is principally controlled kinetically at lower temperatures, and thermodynamically at higher temperatures. The sec-butylation gave similar results to the isopropylation. Although the selectivities for 4,4′-di-sec-butylbiphenyl (4,4′-DSBB) were higher than those in the isopropylation, predominant isomers were 2,x′-DSBB (2,2′-, 2,3′-, and 2,4′-) at lower temperatures, and 3,4′- and 3,3′-DSBB at higher temperatures. The tert-butylation gave 4,4′-di-tert-butylbiphenyl (4,4′-DTBB) in moderate to high selectivities over all zeolites at moderate temperatures: the selectivity for 4,4′-DTBB was higher than 80% over BEA and CON; however, it still remained at 50% over FAU. FAU channels with super cages are too large for selective formation of 4,4′-DTBB.

From these results, it is concluded that the selectivity for 4,4′-DABP in the alkylation over MOR, FAU, BEA, and CON is determined by the exclusion of bulky isomers at their transition states, and that the exclusion is caused by the steric restriction at the transition states of bulky isomers by the zeolite channels.     

Synthesis and application of fluorescein- and biotin-labeled molecular probes for the chemokine receptor CXCR4

The design, synthesis, and bioevaluation of fluorescence- and biotin-labeled CXCR4 antagonists are described. The modification of D-Lys8 at an epsilon-amino group in the peptide antagonist Ac-TZ14011 derived from polyphemusin II had no significant influence on the potent binding of the peptide to the CXCR4 receptor. The application of the labeled peptides in flow cytometry and confocal microscopy studies demonstrated the selectivity of their binding to the CXCR4 receptor, but not to CXCR7, which was recently reported to be another receptor for stromal cell-derived factor 1 (SDF-1)/CXCL12.