The pozzolanic reactivity of monodispersed nanosilica hydrosols and their influence on the hydration characteristics of Portland cement

This study reveals that the nanosilica hydrosols with higher specific surface areas had faster pozzolanic reactivity, especially at early ages; moreover, the results are indicative of the accelerating influence of nanosilicas and silica fume on the hydration of cement. Faster initial and final setting times observed for cement pastes containing nanosilicas are consequence of these mechanisms. However, less hydration degree of cement compared to the plain paste was observed at age of 7 days and after. This can be attributed to the entrapment of some of mix water in the aggregates of nanosilicas formed in cement paste environment, making less water available for the progress of cement hydration. The same mechanism is believed to be responsible for the reduction of flowability of cement pastes.     

A new manufacturable filter design approach for spectral reflectance estimation

Selection of the best possible filter set among a set of available filters is the obvious method of increasing dimension of camera signals for spectral reflectance reconstruction. There are also methods that are focusing on the filter design regardless of noticing to the constructability of the designed filters. This study shows that direct optimization of physical variables of filter manufacturing technique is more reliable than indirect approach of designing and then physical manufacturing of the designed filters. Direct optimization of the transmission‐controlling primaries in filter manufacturing process would guarantee having the designed filters in reality. Combination of some solvent dyes was used as the spectral transmission matching system for filter manufacturing. As a conventional technique, filters were designed and best possible dye concentrations that match the desired filters were calculated. As an alternative approach, filters were also designed using direct optimization of dyes concentrations. The results showed that direct optimization of dye concentrations exhibits better performance in comparison with the conventional technique. © 2016 Wiley Periodicals, Inc. Col Res Appl, 42, 316–326, 2017     

High‐performance carboxylate superplasticizers for concretes: Interplay between the polymerization temperature and properties

Polycarboxylate superplasticizers based on acrylic acid (AA) and maleic anhydride (MAn) were synthesized via free‐radical copolymerization with an ethylene glycol monomer and characterized. The copolymerization temperature (ranging from 50 to 90 °C) appeared to be the key operating factor governing the chemical structure of the superplasticizers. The chemical structures of the products were analyzed by gel permeation chromatography, whereas an optimized sample was further analyzed by Fourier transform infrared spectroscopy and ¹H‐NMR. Superplasticizers of the AA and MAn classes were then incorporated into concrete, and their performances were measured by slump and slump loss tests, where a large dependency of the microstructure on the synthesis temperature was recognized. The optimum temperatures were found to be 50 and 80 °C for the AA and MAn modifiers, respectively. At their own optimum temperatures, the AA and MAn superplasticizer revealed slump losses from 23 to 4 cm and 15 to 5 cm, respectively, after 45 min. The chemical structures of the plasticizers were patterned illustratively to speculate the performance of each superplasticizer according to changes that took place in the backbone length and side‐chain density. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44908.     

Fabricating and robust artificial neural network modeling nanoscale polyurethane fiber using electrospinning method

With regard to the fact that currently there is no comprehensive method to predict diameter of polyurethane/solvent fiber from electrospinning, in this study, diameter prediction of polyurethane/solvent fiber was conducted using neural networks and an error of 166 nm was observed. This error shows that artificial neural networks (ANNs) can predict diameter of electrospinning polyurethane fibers well. Then, considering weak repeatability nature of electrospinning in fabricating fibers with desired diameter, least mean square is used to improve stability of neural network model that shows an error of 113 nm, which represented better results compared to common ANN. To investigate the effect of each one of parameters affecting fiber diameter, sensitivity analysis was conducted. Along with this predicting model, sensitivity analysis can be used to reduce parameters space before conducting future studies. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45116.     

Induction time,storage capacity,and rate of methane hydrate formation in the presence of SDS and silver nanoparticles

In this communication, the kinetic parameters of methane hydrate formation (induction time, quantity and rate of gas uptake, storage capacity (SC), and apparent rate constant) in the presence of sodium dodecyl sulfate (SDS), synthetized silver nanoparticles (SNPs), and mixture of SDS?+?SNPs have been studied. Experimental measurements were performed at temperature of 273.65?K and initial pressure of 7?MPa in a 460?cm³ stirred batch reactor. Our results show that adding SDS, SNPs and their mixture increases the quantity of gas uptake, water to hydrate conversion, and SC of methane hydrate formation, noticeably. Using 300?ppm SDS increases the SC and the quantity of methane uptake 615, and 770%, respectively, compared with pure water. Investigating the hydrate growth rate at the start of hydrate formation process shows that, using SNPs, SDS, and their mixture increases the initial apparent rate constant of hydrate rate, considerably. Our results show that the system of methane?+?water?+?SDS 500?ppm?+?SNPs 45?µM represents the maximum value of initial apparent rate constant, compared with other tested systems.     

Substrate Temperature Dependent Surface Morphology and Photoluminescence of Germanium Quantum Dots Grown by Radio Frequency Magnetron Sputtering

The visible luminescence from Ge nanoparticles and nanocrystallites has generated interest due to the feasibility of tuning band gap by controlling the sizes. Germanium (Ge) quantum dots (QDs) with average diameter ~16 to 8 nm are synthesized by radio frequency magnetron sputtering under different growth conditions. These QDs with narrow size distribution and high density, characterized using atomic force microscopy (AFM) and field emission scanning electron microscopy (FESEM) are obtained under the optimal growth conditions of 400 °C substrate temperature, 100 W radio frequency powers and 10 Sccm Argon flow. The possibility of surface passivation and configuration of these dots are confirmed by elemental energy dispersive X-ray (EDX) analysis. The room temperature strong visible photoluminescence (PL) from such QDs suggests their potential application in optoelectronics. The sample grown at 400 °C in particular, shows three PL peaks at around ~2.95 eV, 3.34 eV and 4.36 eV attributed to the interaction between Ge, GeO_x manifesting the possibility of the formation of core-shell structures. A red shift of ~0.11 eV in the PL peak is observed with decreasing substrate temperature. We assert that our easy and economic method is suitable for the large-scale production of Ge QDs useful in optoelectronic devices.     

Use of axial dispersion model for determination of Sherwood number and mass transfer coefficients in a perforated rotating disc contactor

The mass transfer process in a perforated rotating disk contactor (PRDC) using a toluene-acetone-water system was investigated.The volumetric overall mass transfer coefficients are calculated in a PRDC column.Both mass transfer directions are considered in experiments.The influences of operating variables containing agitation rate,dispersed and continuous phase flow rates and mass transfer in the extraction column are studied.According to obtained results,mass transfer is significantly dependent on agitation rate,while the dispersed and continuous phase flow rates have a minor effect on mass transfer in the extraction column.Furthermore,a novel empirical correlation is developed for prediction of overall continuous phase Sherwood number based on dispersed phase holdup,Reynolds number and mass transfer direction.There has been great agreement between experimental data and predicted values using a proposed correlation for all operating conditions.     

Colour and ergonomics: On the selection of a “colour of the year”

The key role of colour in ergonomics has been emphasized by a number of researchers and design professionals. Although several research studies have been published regarding the use of colour in ergonomics, there are still some areas that need to be considered. The issue of deciding a “colour of the year” is an example, which represents a new challenge for researchers in the field of ergonomics. This is of particular interest considering the fact that the nature of research on the selection of a “colour of the year” is generally based on user experience. This paper argues that ergonomics should play a more prominent role in this field to ensure better user experience and performance. This paper highlights specific areas that need further study and development.     

Effect of Active Gas on Weld Shape and Microstructure of Advanced A-TIG-Welded Stainless Steel

Advanced A-TIG method was conducted to increase the weld penetration and compared with the conventional TIG welding process.A two-pipeline setup was designed to apply Ar + CO_2 mixed gas as the outer layer,while pure argon was applied as the inner layer to prevent any consumption of the tungsten electrode.The results indicate that the presence of active gas in the molten pool led to the change in the temperature coefficient of surface tension so that the Marangoni convection turns inward and forms a deep weld zone.The increase in gas flow rate causes a decrease in the weld efficiency which is attributed to the increase in oxygen content in the weld pool and the formation o f a thicker oxide layer on the weld surface.Moreover,the stir and the temperature fluctuation,led by double shielding gas,create more homogeneous nucleation sites in the molten pool so that a fine grain micros true ture was obtained.