Volumetric out-of-furnace heat treatment of 3600-M3 decomposers

Specifications require that all the welds in 12-m-diam. decomposers with a capacity of 3600 m³ be subjected to high-temperature tempering before going into service in order to alleviate the stresses from the welding operation. Specialists at the organizations VNIIPTkhimnefteapparatury and VNIImontazhspetsstroi have proposed out-of-furnace volumetric (complete) of the assembled decomposer with the use of special heaters. The use of this heating method has shortened assembly operations while providing the welds with a highquality heat treatment and reducing the stresses overall (including welding stresses, stresses from assembly of the decomposer, etc.) The technology ensures uniform heating of the housing of the decomposer and provides for close control over the process. The experience gained in heat-treating decomposers can also be used in the construction of other containers that come into contact with corrosive media. __________ Translated from Metallurg, No. 3, pp. 61–64, March, 2006.     

An element-based displacement preconditioner for linear elasticity problems

Finite element analysis of problems in structural and geotechnical engineering results in linear systems where the unknowns are displacements and rotations at nodes. Although the solution of these systems can be carried out using either direct or iterative methods, in practice the matrices involved are usually very large and sparse (particularly for 3D problems) so an iterative approach is often advantageous in terms of both computational time and memory requirements. This memory saving can be further enhanced if the method used does not require assembly of the full coefficient matrix during the solution procedure. One disadvantage of iterative methods is the need to apply preconditioning to improve convergence. In this paper, we review a range of established element-based preconditioning methods for linear elastic problems and compare their performance with a new method based on preconditioning with element displacement components. This new method appears to offer a significant improvement in performance.     

On the credibility of manet simulations

Simulation is useful for evaluating protocol performance and operation. However, the lack of rigor with which it's applied threatens the credibility of the published research within the manet research community. Mobile ad hoc networks (manets) allow rapid deployment because they don't depend on a fixed infrastructure. Manet nodes can participate as the source, the destination, or an intermediate router. This flexibility is attractive for military applications, disaster-response situations, and academic environments where fixed net working infrastructures might not be available.     

Reliable eye-diagram analysis of data links via device macromodels

This paper addresses the impact of device macromodels on the accuracy of signal integrity and performance predictions for critical digital interconnecting systems. It exploits nonlinear parametric models for both single-ended and differential devices, including the effects of power supply fluctuations and receiver bit detection. The analysis demonstrates that the use of well-designed macromodels dramatically speeds up the simulation as well it preserves timing accuracy even for long bit sequences.     

Pre-Processing of Integral Images for 3-D Displays

This paper seeks to explore a method to accurately correct geometric distortions caused during the capture of three-dimensional (3-D) integral images. Such distortions are rotational and scaling errors which, if not corrected, will cause banding and moire effects on the replayed image. The method for calculating the angle of deviation in the 3-D Integral Images is based on Hough Transform. It allows detection of the angle necessary for correction of the rotational error. Experiments have been conducted on a number of 3-D integral image samples and it has been found that the proposed method produces results with accuracy of 0.05 deg     

Influence of the second phase on the room-temperature tensile and creep deformation mechanisms of α-β titanium alloys: Part I. Tensile deformation

The effects of α and β phase interactions on the room-temperature tensile and creep deformation behavior of α + β titanium alloys with Widmanst?tten microstructures were studied using Ti-6.0 wt pct Mn and Ti-8.1 wt pct V as the model two-phase alloy systems. This article, Part I, deals with tensile deformation. It was found that when the α phase is present as thin (<10-μm) plates in the α + β alloys, significant twinning occurs. No significant twinning was observed in single-phase alloys with the same chemistry and similar grain size. Additionally, the β phase of Ti-8.1 V deforms by stress-induced hexagonal martensite (α′), while only twinning occurs in the single-phase β alloy with the same chemistry. Twinning in the α phase in association with stress-induced martensite (SIM) in the β phase was observed for the first time in a two-phase titanium alloy. This behavior is explained in terms of a number of factors including elastic interaction stresses between the α and β phases, coherency between the α phase and hexagonal martensite, and β phase stability.     

Vacuum degassing of chromium-nickel-molybdenum steel at the Magnitogorsk Metallurgical Combine

The Magnitogorsk Metallurgical Combine has conducted a study of the effect of technological factors on the hydrogen content of chromium-nickel-molybdenum steel after vacuum degassing. It was established that the most important factor is the hydrogen content of the steel before the degassing operation. The study also determined the effects of the circulation coefficient, the duration of the degassing operation, and the vacuum used in the treatment. __________ Translated from Metallurg, No. 7, pp. 68–69, July, 2006.     

Experimental studies of the bond response of three-wire strands and some influencing parameters

The bond behavior of prestressing strands is of great importance for the capacity of precast prestressed concrete structures. In the present study, the bond behavior of three-wire strands, and some influencing parameters, were examined by means of steel encased pull-through and push-in tests. The three mechanisms: adhesion, friction and other mechanical actions were found to be present at the strand-concrete interface at different slip values. The results from the experiments showed that the micro roughness of the strand surface strongly affected the initial bond response of the strand, that is the adhesion in the interface. The maximum bond capacity of indented three-wire strands was found to be directly connected to the geometric properties of the strand indents. The influence of the concrete strength on the bond capacity of the strand was hard to interpret. However, the density of the concrete matrix was found to be a better parameter for determine the influence of the concrete rather than the compressive strength.     

Note on B-splines, wavelet scaling functions, and Gabor frames

Let g be a continuous, compactly supported function on such that the integer translates of g constitute a partition of unity. We show that the Gabor system (g,a,b), with window g and time-shift and frequency-shift parameters a,b>0 has no lower frame bound larger than 0 if b=2,3,... and a>0. In particular, (g,a,b) is not a Gabor frame if g is a continuous, compactly supported wavelet scaling function and if b=2,3,... and a>0. We give an example for our result for the case that g=B/sub 1/, the triangle function supported by [-1,1], by showing pictures of the canonical dual corresponding to (g,a,b) where ab=1/4 and b crosses the lines N=2,3,.     

Understanding silica-supported metal catalysts: Pd/silica as a case study

Supported metal catalysts, particularly noble metals supported on SiO₂, have attracted considerable attention due to the importance of the silica–metal interface in heterogeneous catalysis and in electronic device fabrication. Several important issues, e.g., the stability of the metal–oxide interface at working temperatures and pressures, are not well-understood. In this review, the present status of our understanding of the metal–silica interface is reviewed. Recent results of model studies in our laboratories on Pd/SiO₂/Mo(1 1 2) using LEED, AES and STM are reported. In this work, epitaxial, ultrathin, well-ordered SiO₂ films were grown on a Mo(1 1 2) substrate to circumvent complications that frequently arise from the silica–silicon interface present in silica thin films grown on silicon.