Study on fabrication of 3-D microstructures by synchrotron radiation based on pixels exposed lithography

We report research on the development of a method of fabricating three-dimensional microstructures that uses synchrotron radiation light. Some research on three-dimensional processing methods using SR lithography has already been reported. They have involved techniques of applying exposure energy distributions to resist surfaces. Complicated energy distributions need to be applied to resist surfaces to fabricate arbitrary three-dimensional structures. However, we devised a new method that made it possible to fabricate arbitrary three-dimensional microstructures by using a mask with pattern created function. The advantages of this method are that it is suitable for rapid prototyping and it reduces the fabrication time and cost since it is not necessary to fabricate conventional photolithographic masks. Our research involved a basic experiment on this method of fabrication where we succeeded in fabricating a free-form surface by exposing it through an overlapping array of pixels that created a single aperture. Moreover, the pixel size could be made smaller than the aperture size by overlapping adjoining pixels.     

High-speed source-heterojunction-MOS-transistor (SHOT) utilizing high-velocity electron injection

We have developed the source-heterojunction-MOS-transistor (SHOT), a novel high-speed MOSFET with relaxed-SiGe/strained-Si heterojunction source structures for quasi-ballistic or full-ballistic transistors. Using the band-offset energy at the source SiGe/strained-Si heterojunction, high velocity electrons can be injected into the strained-Si channel from the SiGe source region. For the first time, we have experimentally demonstrated that the transconductance is enhanced in SHOT for high applied drain voltage, compared to that of strained- and conventional silicon-on-insulator MOSFETs. We have also shown that the transconductance enhancement in SHOT depends on both the gate drive and the drain bias.     

Ethanol Conversion on MCM-41 and FSM-16, and on Ni-Doped MCM-41 and FSM-16 Prepared without Hydrothermal Conditions

MCM-41 and FSM-16 were both prepared using no hydrothermal conditions, and nickel was doped into these catalysts (Ni-MCM-41 and Ni-FSM-16) using a template ion exchange method. FSM-16 and Ni-FSM-16 had greater catalytic activity for the conversion of ethanol than MCM-41 and Ni-MCM-41, indicating that FSM-16 has potential as a catalyst for the conversion of ethanol to propylene.     

Classification and identification of strains of Lactobacillus brevis based on electrophoretic characterization of D-lactate dehydrogenase: relationship between D-lactate dehydrogenase and beer-spoilage ability

The cell-free extracts of 60 strains which were identified phenotypically as being those of Lactobacillus brevis, including 48 isolates from the environment and 12 reference strains, were applied to polyacrylamide gel electrophoresis for extracting their NAD-dependent D- and L-lactate dehydrogenases (LDH). These strains were divided into 5 groups, i.e., Groups A, B, C, D, and E, on the basis of the electrophoretic mobilities of their D-LDH. The strains showed variations in their carbohydrate fermentation patterns. No relationship between the profile of D-LDH and the carbohydrate fermentation pattern was recognized. However, there appeared to be a relationship between the D-LDH profile and the beer-spoilage ability, because 40 out of 44 beer-spoilage strains identified as L. brevis were classified to Group B. We purified D-LDHs from the so-called complete beer-spoilage strain SBC 8002 of LDH Group B and from the non beer-spoilage strains JCM 1059T of LDH Group A and AHU 1508 of LDH Group C. Although the purified D-LDHs had the same molecular weight (84 kDa), each possessed a different optimum pH, optimum temperature, and isoelectric point. The aforementioned parameter values for the enzyme from the so-called complete beer-spoilage strain SBC 8002 of LDH Group B were 10.0, 50 degrees C, and 4.1, respectively; this strain was discriminated from the D-LDHs of the other two non beer-spoilage strains especially by its optimum temperature (50 degrees C).     

Improved polyhydroxybutyrate (PHB) production in transgenic tobacco by enhancing translation efficiency of bacterial PHB biosynthetic genes

Polyhydroxybutyrate [P(3HB)] was produced in the transgenic tobacco harboring the genes encoding acetoacetyl-CoA reductase (PhaB) and polyhydroxyalkanoate synthase (PhaC) from Ralstonia eutropha (Cupriavidus necator) with optimized codon usage for expression in tobacco. P(3HB) contents in the transformants (0.2mg/g dry cell weight in average) harboring the codon-optimized phaB gene was twofold higher than the control transformants harboring the wild-type phaB gene. The immunodetection revealed an increased production of PhaB in leaves, indicating that the enhanced expression of PhaB was effective to increase P(3HB) production in tobacco. In contrast, codon-optimization of the phaC gene exhibited no apparent effect on P(3HB) production. This result suggests that the efficiency of PhaB-catalyzed reaction contributed to the flux toward P(3HB) biosynthesis in tobacco leaves.     

Blunt corners of WC grains induced by lowering carbon content in WC–12mass%Co cemented carbides

Habit planes at WC/Co interfaces were investigated from a viewpoint of carbon content in WC–12mass%Co cemented carbides by transmission electron microscopy (TEM). WC/Co interfaces typically consist of (0001) and { 10[`1]0} \{ 10\bar{1}0\} habit planes with blunt corners, which are very close to { 10[`1]1} \{ 10\bar{1}1\} habit plane. The sizes of the blunt corners increase as the carbon content decrease. The expansions of blunt corners are due to the change in interface energy caused by the variation of the carbon content. The change in interface energy is discussed in terms of the incoherency between the (0001) planes of the WC grains and the Co-phase.     

Energy-level alignment at model interfaces of organic electroluminescent devices studied by UV photoemission: trend in the deviation from the traditional way of estimating the interfacial electronic structures

The electronic structures of model interfaces of organic electroluminescent (EL) devices were investigated with UV photoemission spectroscopy (UPS). Interfaces of TTN (tetrathianaphthacene) and TCNQ (tetracyanoquinodimethane) were also studied as extreme cases for hole transport and electron transport material, respectively. For all organic/metal interfaces studied, the work function of metal electrode was changed by deposition of organic layer, i.e., the vacuum level was shifted at the interface, indicating the invalidity of the traditional energy level alignment model where a common vacuum level was assumed at organic/metal interface. At TCNQ/Au, DP-NTCI/Al, which are acceptor/metal interfaces, upward shift of the vacuum level of organic layer relative to that of metal was observed, suggesting the formation of interfacial dipole due to electron-transfer from metal to acceptor. At other organic/metal interfaces, TPD(N, N'-diphenyl-N, N'-(3-methylphenyl)-1, 1'-biphenyl-4, 4'-diamine)/Au or ITO (indium tin oxide), ALq/sub 3/ (tris(8-hydroxyquinolino) aluminum)/Al, DP-NTCl(N, N'-diphenyl-1,4,5,8- naphthyltetracarboxylimide)/Al or Au, downward shift of the vacuum level was observed. Such downward shift has been also observed in our previous study for porphyrin/metal interfaces, and seems to be a trend for organic/metal interfaces at which no electron-transfer from metal to organic layer occurs. This trend suggests that the traditional model tends to underestimate (overestimate) the barrier height for hole (electron) injection. On the other hand, the vacuum level shift at ALq/sub 3//TPD interface was less than 0.1 eV, leading to an apparent applicability of the traditional model. However, it is not always the case for organic/organic interfaces: finite shift of 0.2 eV was observed at TTN/TCNQ interface due to electron-transfer from TTN to TCNQ. Possible origins of vacuum level shift at organic/metal interfaces were also discussed.     

Use of multivariate analysis for the improvement in prediction accuracy of bacterial aerobic plate count by flow cytometry

Flow cytometry (FCM) and aerobic plate count (APC) by the culture method were performed on green tea samples spiked with Escherichia coli type strain NCTC9001 (ATCC11775) solutions of different concentrations. In FCM, fluorescence signals from multiple stained bacteria and other fluorophores are detected using detector channels, and recorded as events with a voltage at each channel. FCM data were analyzed in two ways: conventional and multivariate analysis. In the former, the number of events with voltages larger than the defined threshold values was regarded as the predicted APC. In the latter, voltage histograms of all channels were obtained and merged horizontally to serve as explanatory variables. Then a partial least squares regression (PLSR) model was built to predict APC from the histogram data. The coefficient of determination (R²) and the root mean square error (RMSE) between APC by the culture method and that predicted by conventional FCM were 0.916 and 1.08 cfu/ml². The APC values predicted by the PLSR model and those measured were in good agreement with R² of 0.982 and RMSE of 0.417 cfu/ml, which verified the potential of the proposed method for improving APC prediction accuracy by FCM.     

Methodology to optimize radiation protection in radioactive waste disposal after closure of a disposal facility based on probabilistic approach

We propose a methodology to optimize radiation protection in radioactive waste disposal after the closure of a disposal facility based on a probabilistic approach. In this methodology, a set of alternative options of the disposal system design with the associated uncertainties estimated through a probabilistic approach are developed. Then, the methodology evaluates the advantages and disadvantages of each option for the optimization of radiation protection, in which it is possible to determine the compliance with a dose constraint of 0.3 mSv/y and to collect information for making a decision on the optimization. In particular, the obtained information on the exposure, which is the mode and width of the dose distribution, can be converted into information on engineering measures and site conditions for the options. This process allows us to discuss which option should be selected as the optimal option by considering the balance between the exposure and the engineering, economic, and social feasibility of the option. This methodology is helpful for providing clear reasons why an optimal disposal system design is selected by combining quantitative information on the exposure and the feasibility of each option.