Erosion of atmospheric plasma sprayed rare earth oxide coatings under air suspended corundum particles

Atmospheric plasma sprayed (APS) zirconium oxide based coatings are used widely in aero engine components for providing thermal insulation, improving the corrosion and oxidation resistance. Despite its wide spread industrial use, little is known about the basic erosion behaviour and the mechanisms by which such coatings erode. In this paper, the erosive wear behaviours of Yttria Stabilized Zirconia (YSZ) coatings; Lanthanum Zirconate (LZ) coatings and Inconel 738 base material (BM) were studied and compared under air jet erosion conditions with corundum particles as erodent material. The erosion behaviour was studied with respect to the different porosity volume percentages of the coatings and the changes in velocity of erodent, impact angle of erodent and erodent particle flux. It was found that in solid particle erosion, the wear resistances of YSZ and LZ coatings were the best at their lowest porosity volume and it decreased with the increase in the percentage volume of porosity. There was a linear increase in the wear resistance with the increase in hardness. Further, relationships among the erosion parameters with respect to erosive wear loss were derived by using the response surface methodology and the erosion mechanisms were discussed adequately.     

Effect of soluble fibre (guar gum and carboxymethylcellulose) addition on technological, sensory and structural properties of durum wheat spaghetti

Incorporation in pasta of either of two soluble fibres, carboxymethylcellulose sodium salt (CMC) and guar gum (GG), was found to significantly reduce the rate of invitro starch digestion. The amount of reducing sugars produced over 300 min was reduced by 18% at 1.5% CMC incorporation and 24% at 20% GG incorporation. Negative effects on sensory and technological properties were seen at the high levels of GG needed to reduce the rate of in vitro digestion, and a ‘matty’ layer covering the surfaces of starch granules was observed by scanning electron microscopy and confocal scanning laser microscopy. By contrast, levels of CMC incorporation giving large reductions in in vitro digestion had no negative effects on pasta properties. No significant alteration in pasta structure on CMC incorporation was observed by microscopy. The large difference in the amounts of soluble fibre required to bring about equivalent reductions in digestion rate suggests that different mechanisms may be involved in the two cases.     

Exploring the Influence of Methylene Diphenyl Diisocyanate as a Modifier for Ethylene Vinyl Acetate/Thermoplastic Polyurethane Blends

Ethylene vinyl acetate (EVA)/thermoplastic polyurethane (TPU) blend at various blend ratios has been modified via reactive processing with 4,4′-methylene diphenyl diisocyanate (MDI). Modification of the blends with even small amount of MDI shows significant improvement in physico-mechanical properties for EVA/TPU 50/50 and 30/70 blends, and it is also supported by the superior melt rheological behavior and dramatic improvement in oil resistance property. After the treatment of electron beam (dose range: 50–150?kGy), radiation crosslinked EVA/TPU (30:70) blend reveals further improvement in various properties. This particular material can find potential application as cable sheathing component.     

Wear behavior of alloyed hypereutectic gray cast iron

Alloyed gray cast iron of varying compositions was studied for their wear behavior. In general, the alloyed gray irons studied have higher graphite volume fraction (∼20%) with Type-A graphite flake morphology. Base cast iron showed two to three times higher wear rates than the alloyed gray irons. Tensile strength and wear rates show decreasing trend with increase in graphite and carbide volume fraction. Wear track analysis shows three body abrasive wear mode resulting in debris generation and smudging along the wear tracks. The graphite gets released during sliding to form films along the wear tracks and then forms irregular debris.     

Asiatic acid prevents lipid peroxidation and improves antioxidant status in rats with streptozotocin-induced diabetes

Oxidative stress is a common pathogenesis of diabetes mellitus and asiatic acid (AA) plays an important role in ameliorating those difficulties. The present study was designed the protective effects of AA on altered lipid peroxidation products, enzymic and nonenzymic antioxidants in streptozotocin (STZ)-induced diabetic rats. Diabetes was induced in experimental rats by single dose STZ (40 mg/kg b.w.) injection. Diabetic rats showed significantly increased levels of plasma glucose, thiobarbituric acid reactive substances, lipid hydroperoxides, aspartate aminotransferase, alanine aminotransferase, bilirubin, creatine kinase, urea, uric acid, creatinine and decreased levels of plasma insulin. The activities of enzymatic antioxidants such as superoxide dismutase, catalase, glutathione peroxidase and glutathione-S-transferase and the levels of non-enzymatic antioxidants such as vitamin C, vitamin E and reduced glutathione were decreased in diabetic rats. Oral treatment with AA (20 mg/kg b.w.) showed near normalized levels of plasma glucose, insulin, lipid peroxidation products, enzymatic and nonenzymatic markers in diabetic rats. The results demonstrate that AA possesses potent antioxidant effect comparable with glibenclamide in improving antihyperglycemia and attenuating antioxidant status in diabetic rats.     

Characterization of Morphological Changes in Agglomerates Subject to Condensation and Evaporation Using Multiple Fractal Dimensions

Multiple fractal dimensions are used to characterize morphological changes that occur when an aerosol composed of irregularly shaped agglomerates is subject to condensation followed by evaporation. The agglomerates change from a branched, chainlike structure to a more regular, near-spherical or clumplike structure reflected in a decrease in the structural fractal dimension. The textural fractal dimension remains constant because the primary particles, of which the agglomerates are composed, do not change in shape. The degree of supersaturation and the number of condensation-evaporation cycles that the aerosol undergoes are major factors that influence morphological change. Even at low supersaturations, increasing the number of condensation-evaporation cycles makes the agglomerates more regular and thus decreases the structural fractal dimension. The transition point in the Richardson plot is a good indicator of the size of the primary particles in the agglomerate.     

Effect of channel geometry on solute dispersion in pressure-driven microfluidic systems

Pressure-driven transport of fluid and solute samples is often desirable in microfluidic devices, particularly where sufficient electroosmotic flow rates cannot be realized or the use of an electric field is restricted. Unfortunately, this mode of actuation also leads to hydrodynamic dispersion due to the inherent fluid shear in the system. While such dispersivity is known to scale with the square of the Peclet number based on the narrower dimension of the conduit (often the channel depth), the proportionality constant can vary significantly depending on its actual cross section. In this article, we review previous studies to understand the effect of commonly microfabricated channel cross sections on the Taylor–Aris dispersion of solute slugs in simple pressure-driven flow systems. We also analyze some recently proposed optimum designs which can reduce the contribution to this band broadening arising from the presence of the channel sidewalls. Finally, new simulation results have been presented in the last section of this paper which describe solutal spreading due to bowing of microchannels that can occur from stresses developed during their fabrication or operation under high-pressure conditions.     

UbiqStack: a taxonomy for a ubiquitous computing software stack

This paper describes a taxonomy for a ubiquitous computing software stack called UbiqStack. Through the lens of the UbiqStack taxonomy we survey a variety of subsystems designed to be the building blocks from which sophisticated infrastructures for ubiquitous computing are assembled. Our experience shows that many of these building blocks fit neatly into one of the five UbiqStack categories, each containing functionally-equivalent components. Effectively identifying the best-fit “Lego pieces”, which in turn determines the composite functionality of the resulting infrastructure, is critical. The selection process, however, is impeded by the lack of convention for labeling these classes of building blocks. The lack of clarity with respect to what ready-made subsystems are available within each class often results in naive re-implementation of ready-made components, monolithic and clumsy implementations, and implementations that impose non-standard interfaces onto the applications above. This paper describes the UbiqStack classes of subsystems and explores each in light of the experience gained over 2 years of active development of both ubiquitous computing applications and software infrastructures for their deployment.     

Ranking and Reranking with Perceptron

This work is inspired by the so-called reranking tasks in natural language processing. In this paper, we first study the ranking, reranking, and ordinal regression algorithms proposed recently in the context of ranks and margins. Then we propose a general framework for ranking and reranking, and introduce a series of variants of the perceptron algorithm for ranking and reranking in the new framework. Compared to the approach of using pairwise objects as training samples, the new algorithms reduces the data complexity and training time. We apply the new perceptron algorithms to the parse reranking and machine translation reranking tasks, and study the performance of reranking by employing various definitions of the margins.Editors: Dan Roth and Pascale Fung     

Rheological characterization of hydroxypropylcellulose gels

The present paper describes the rheological properties of hydroxypropylcellulose (HPC) gels formulated in propylene glycol (PG), water, ethanol, and mixtures of these components. The effects of molecular weight, polymer concentration, and solvent composition on the apparent viscosity and flow characteristics have been studied by continuous shear rheometry. The HPC gels are shear thinning and do not exhibit significant yield or hysteresis in their rheograms. The apparent viscosity increases with increasing molecular weight and concentration of the polymer, as expected. Although not so pronounced at lower concentrations (≤ 1.5%), HPC gels tend to become increasingly non-Newtonian with increasing molecular weight at higher polymer concentrations (3%). A mathematical model has been proposed for the prediction of viscosities of HPC gels. There exists a high degree of dependence on molecular interactions between various solvent molecules in the prediction of mixture viscosities in ternary systems. The effects of solvent composition on the viscoelastic behavior of these gels have also been examined by dynamic mechanical analysis. The HPC gels are highly viscoelastic and exhibit greater degrees of elasticity with increased PG content in ternary solvent mixtures with water and ethanol. The study also suggests that dynamic mechanical analysis could prove to be a useful tool in the determination of zero-shear viscosities, viscosities that are representative of most realistic situations.