Zerstörungsfreie Bestimmung elastischer Eigenschaften quadratischer 3-schichtiger Brettsperrholzplatten mit symmetrischem Aufbau

Some of the most important material properties of engineered wood products, like cross-laminated solid wood panels, are the elastic properties. Regarding panels, the two in plane MOEs (E_ii) and three shear moduli (G_ij) are of particular interest. In order to determine these parameters with an economically and non-destructive technique, a method was developed which allows to determine all five parameters in one experiment only. This method was approved on 24 square-shaped cross-laminated solid wood panels with side-length of 2.5 m, thickness of 70 mm and two different layer sizes. The panels were produced by two plants applying different technologies. The determined elastic parameters were verified by bending tests and compared with stiffness parameters calculated on basis of the elastic compound theory. Four elastic parameters could be determined and proven to be correct. The results did neither depend on the different production technologies of the panels nor on the two different compositions of layers. The determinability of the elastic parameter G₂₃ depends on the geometry of the panels. Noteworthy is the fact that stiffness parameters calculated assuming that the raw material of the single layers corresponds to strength class C24, can be on the ‘‘unsafe side’’.     

Adaptive memory search for multidemand multidimensional knapsack problems

We describe a simple adaptive memory search method for the 0/1 Multidemand Multidimensional Knapsack Problem (0/1 MDMKP). The search balances the level of infeasibility against the quality of the solution, and uses a simple dynamic tabu search mechanism. A weighting scheme to balance out the differences in the tightness of the constraints is also implemented. Computational results on a portfolio of test problems taken from the literature are reported, showing very favorable results, both in terms of solution quality and the ability of the search to find feasible solutions.     

Mechanisms of weight maintenance under high- and low-protein, low-glycaemic index diets

Scope: Weight maintenance after intended weight loss is a challenge in an obesogenic environment. In a large multicentre dietary intervention study (DiOGenes), it has recently been demonstrated that a high‐protein/low‐glycaemic index (HP/LGI) diet was slightly more efficient in maintaining weight loss than low‐protein/LGI or high‐GI (LP/LGI or HGI) diets. Here, we use a proteomic approach to assess the molecular mechanisms behind this positive effect. Methods and results: A subset of the most successful (weight loser, n=12) and unsuccessful (weight re‐gainer, n=12) individuals consuming the LGI diets with either high‐ or low‐protein content (HP or LP/LGI), following an initial calorie deficit run‐in weight loss phase, were analyzed at the plasma protein level. Proteomic analysis revealed 18 proteins regulated after 6 months of the dietary weight maintenance phase. Furthermore, 12 proteins were significantly regulated as a function of success rate under an HP diet, arising as candidate biomarkers of mechanisms of successful weight maintenance under an HP/LGI diet. Pregnancy‐zone protein (PZP) and protein S (PROS1) were revealed as novel biomarkers of weight maintenance showing opposite effects. Conclusion: Semantic network analysis of the 12 regulated proteins revealed that under an HP/LGI an anti‐atherogenic effect and alterations of fat metabolism were associated with the success of maintaining the initial weight loss.     

Development of novel processable electron accepting conjugated polymers containing fluoranthene units in the main chain

Considerable interest exists in the development of novel n-type conjugated polymers, since many currently available polymer systems have insufficient electron mobility and/or electron affinity. In this work, a universal synthesis route is presented towards a new class of n-type conjugated polymers, i.e. poly(p-fluoranthene vinylene) (PFV) and its derivatives. This route is illustrated with three examples, i.e. unsubstituted PFV and functionalized hexyl-PFV and dodecyl-PFV. All polymers have been synthesized via the dithiocarbamate precursor route. Solubility was introduced by incorporation of alkyl side chains, which leads to a significantly enhanced purity and processability as compared to unsubstituted PFV. Under the applied electrochemical conditions PFV-type polymers demonstrate typical n-type behavior. Additional CELIV mobility measurements on dodecyl-PFV reveal an excellent electron mobility, μ_e = 1.4 × 10⁻⁴ cm²/Vs. Hence, poly(p-fluoranthene vinylene) and its derivatives are promising n-type materials for organic optoelectronic applications.     

On Multirate DS-CDMA Schemes with Interference Cancellation

This paper investigates interference cancellation (IC) in direct-sequence code-division multiple access (DS-CDMA) systems that support multiple data rates. Two methods for implementing multiple data rates are considered. One is the use of mixed modulation and the other is the use of multicodes. We introduce and analyze a new approach that combines these multiple data rate systems with IC. The cancellation in the receiver is performed successively on each user, starting with the user received with the highest power. This procedure can in turn be iterated, forming a multistage scheme, with the number of iterations set as a design parameter. Our analysis employs a Gaussian approximation for the distribution of the interference, and it includes both the AWGN and the flat Rayleigh fading channel. The systems are also evaluated via computer simulations. Our analysis and simulations indicate that the IC schemes used in mixed modulation or multicode systems yield a performance close to the single BPSK user bound and, consequently, give a prospect of a considerable improvement in performance compared to systems employing matched filter detectors.     

Industrial Experience in Pressurized Steam Drying of Beet Pulp,Sewage Sludge and Wood Chips.

ABSTRACT

Drying in superheated steam under pressure gives possibilities for pollution free drying, energy recovery. reduced drying time and a very compact drying equipment.

Products are dried i n a pressurized cellular fluid bed by super heated steam blown through the cells. Above the fluid bed dust is separated before the steam is reheated and recirculated to the cells by a fan. The evaporated water leaves the dryer as usable steam at e.g. 3 bar g, and full energy recovery is obtained. Today 14 plants have been builtor are under construction, with capacities from 2 to 40t / h water evaporation.

This technology is suited for drying of beet pulp, residues from starch production of corn or wheat. sludge. spent grain. brown coal. wood chips and bark.

The technology shows great options for integration in steam systems in various industries, whereby drying is possible without using primary energy and pollution is avoided.     

Reconstructing the Traffic State by Fusion of Heterogeneous Data

Abstract: We present an advanced interpolation method for estimating smooth spatiotemporal profiles for local highway traffic variables such as flow, speed and density. The method is based on the “adaptive smoothing method” which takes as input stationary detector data as typically collected by traffic control centers. We generalize this method to allow for fusion with floating car data or other traffic information. The resulting profiles display transitions between free and congested traffic in great detail, as well as fine structures such as stop‐and‐go waves. We establish the accuracy and robustness of the method and demonstrate three potential applications: (1) compensation for gaps in data caused by detector failure; (2) separation of noise from dynamic traffic information; and (3) the fusion of floating car data with stationary detector data.     

Deceived and distorted: Game outcome retrospectively determines the reported time of action.

Previous work suggested the association between intentionality and the reported time of action was exclusive, with intentionality as the primary facilitator to the mental time compression between the reported time of action and its effect (Haggard, Clark, & Kalogeras, 2002). In three experiments, we examined whether mental time compression could also be observed in an unintended action. Participants performed an externally cued key press task that elicited one of two possible tones. The reported time of action shifted closer to the tone when the tone was used to indicate the winner of a race (Exp.2) compared to when the tone was meaningless and did not indicate winning (Exp.1). This suggests that reported time of an unintended action could shift toward the effect in some contexts. Furthermore, the results from Exp.2 and Exp.3 (tones were substituted with verbal feedback) showed that a presumed winning action was judged to occur earlier whereas a presumed losing action was judged to be later. These findings therefore support the view that the reported time of action is reconstructed from known temporal information rather than determined by intentionality. (PsycINFO Database Record (c) 2011 APA, all rights reserved)     

Flow conditions of fresh mortar and concrete in different pipes

The variation in fresh concrete flow rate over the pipe cross section was investigated on differently coloured and highly flowable concrete mixes flowing through pipes of different materials (rubber, steel, acryl). First, uncoloured (gray) concrete was poured through the pipe and the pipe blocked. Similar but coloured (black) concrete was then poured into the pipe filled with gray concrete, flowing after the gray concrete for a while before being blocked and hardened. The advance of the colouring along the pipe wall (showing boundary flow rate) was observed on the moulded concrete surface appearing after removing the pipe from the hardened concrete. The shapes of the interfaces between uncoloured and coloured concrete (showing variation of flow rate over the pipe cross section) were observed on sawn surfaces of concrete half cylinders cut along the length axes of the concrete-filled pipe. Flow profiles over the pipe cross section were clearly seen with maximum flow rates near the centre of the pipe and low flow rate at the pipe wall (typically rubber pipe with reference concrete without silica fume and/or stabilizers). More plug-shaped profiles, with long slip layers and less variation of flow rate over the cross section, were also seen (typically in smooth acrylic pipes). Flow rate, amount of concrete sticking to the wall after flow and SEM-images of pipe surface roughness were observed, illustrating the problem of testing full scale pumping.