Reactions of conjugated fatty acids. V. Preparation and properties of diels-alder adducts and their esters fromtrans,trans-conjugated fatty acids derived from soybean oil

Summary Soybean fatty acids were conjugated with alkali, and the contained, conjugated dienoic acids were isomerized with iodine to thetrans,trans configuration. Adducts were prepared from thesetrans,trans-conjugated acids by condensation with maleic anhydride and acrylic acid. The adducts were isolated, purified, and converted to esters by using a variety of alcohols, including methyl, ethyl,n-propyl,n-butyl, and allyl alcohols. Esters made from saturated alcohols were converted into the corresponding epoxy derivatives. All of the esters (except allyl) and all of the epoxy esters were compatible with an equal weight of polyvinyl chloride and appeared to be primary plasticizers for this plastic. The epoxy esters were effective in inhibiting heat deterioration of polyvinyl chloride. Presented at fall meeting. American Oil Chemists' Society, September 23–26, 1956, Chicago, Ill.     

Pressure reaction of maleic esters with vegetable oils

The reaction of dimethyl maleate and some related dienophiles with vegetable oils under pressure has been studied successfully. When safflower oil reacts with 100% excess maleate, sulfur dioxide catalyst, and hydroquinone inhibitor at 290° for 1hr., 80 to 90% yields of adduct fraction, based on linoleate, are obtained. Under the same conditions almost equally good yields result with either linseed or soybean oils. With safflower oil, dimethyl fumarate gave slightly lower yields. Di-n-butyl maleate gave even poorer yields, and much residue was formed. Paper II in a series entitled, “Reactions of Dienophiles with Vegetable Oils”. Presented at annual meeting, American Oil Chemists' Society, St. Louis, Mo., May 1–3, 1961. This is a laboratory of the Northern Utilization Research and Development Division, Agricultural Research Service, U.S. Department of Agriculture.     

Production of human normal adult and fetal hemoglobins in Escherichia coli

A hemoglobin expression system in Escherichia coli is described. In order to produce authentic human hemoglobin, we need to co-express both methionine aminopeptidase and globin genes under the control of a strong promoter. We have constructed three plasmids, pHE2, pHE4 and pHE7, for the expression of human normal adult hemoglobin and a plasmid, pHE9, for the expression of human fetal hemoglobin, in high yields. The globin genes can be derived from either synthetic genes or human globin cDNAs. The extra amino-terminal methionine residues of the expressed globins can be removed by the co-expressed methionine aminopeptidase. The heme is inserted correctly into the expressed alpha- globin from our expression plasmids. A fraction (approximately 25%) of the heme is not inserted correctly into the expressed beta- or gamma- globin. However, the incorrectly inserted hemes can be converted into the correct conformation by carrying out a simple oxidation-reduction process on the purified hemoglobin molecule. We have investigated the functional properties of the expressed hemoglobins by measuring their oxygen-binding properties and their structural features by obtaining their 1H-NMR spectra. Our results show that authentic human normal adult and fetal hemoglobins can be produced from our expression plasmids in E. coli and in high yields. Our expression system allows us to design and to produce any recombinant hemoglobins needed for our research on the structure-function relationship in hemoglobin.      

The kinetics of CO2 hydrogenation on a Rh foil promoted by titania overlayers

Submonolayer deposits of titania on a Rh foil have been found to increase the rate of CO₂ hydrogenation. The primary product, methane, exhibits a maximum rate at a TiO _x coverage of 0.5 ML which is a factor of 15 higher than that over the clean Rh surface. The rate of ethane formation displays a maximum which is 70 times that over the unpromoted Rh foil; however, the selectivity for methane remains in excess of 99%. The apparent activation energy for methane formation and the dependence of the rate on H₂ and CO₂ partial pressure have been determined both for the bare Rh surface and the titania-promoted surface. These rate parameters show very small variations as titania is added to the Rh catalyst. The methanation of CO₂ is proposed to start with the dissociation of CO₂ into CO_(a) and O_(a), and then proceed through steps which are identical to those for the hydrogenation of CO. The increase in the rate of CO₂ hydrogenation in the presence of titania is attributed to an interaction between the adsorbed CO, released by CO₂ dissociation, and Ti³⁺ ions located at the edge of TiO _x islands covering the surface. Differences in the effects of titania promotion on the methanation of CO₂ and CO are discussed in terms of the mechanisms that have been proposed for these two reactions.     

Rubber-modified epoxy resins containing high functionality acrylic elastomers

The effect of the functionality of n-butylacrylate/acrylic acid copolymers upon the impact resistance of epoxy resins modified with these rubbery copolymers as a second phase was investigated using a high speed tensile test and scanning electron microscopy. It was found that an optimum functionality of copolymer existed for maximum impact resistance. This optimum value was the result of the competition between the amount of rubber–matrix reaction, an increases in which tended to increase toughness, and solubility of the rubber in the epoxy matrix, which eventually decreased toughness.     

Lewis acidity as an explanation for oxide promotion of metals: implications of its importance and limits for catalytic reactions

Sub-monolayer quantities of metal oxides are found to influence CO hydrogenation, CO₂ hydrogenation, acetone hydrogenation, ethylene hydroformylation, ethylene hydrogenation, and ethane hydrogenolysis over Rh foils. The metal oxides investigated include AlOx, TiOx, VOx, FeOx, ZrOx, NbOx, TaOx, and WOx. Only those reactions involving the hydrogenation of C-O bonds are enhanced by the oxide overlayers. The coverage at which maximum rate enhancement occurs is approximately 0.5 ML for each oxide promoter. Titanium, niobium, and tantalum oxides are the most effective promoters. XPS measurements after reaction show that of the oxides studied titanium, niobium, and tantalum oxide overlayers are stable in the highest oxidation states. The trend in promotion effectiveness is attributed to the direct relationship between oxidation state and Lewis acidity. For the oxide promoters, bonding at the metal oxide/metal interface between the O-end of adsorbed CO and the Lewis acidic oxide is postulated to facilitate C-O bond dissociation and subsequent hydrogenation.     

High-Temperature Structural Phase Transition in Ca0.7Ti0.7La0.3Al0.3O3: Investigation by Synchrotron X-Ray Diffraction

Mixed-oxide prepared Ca_0.7Ti_0.7La_0.3Al_0.3O₃ (CTLA) ceramics (≈96% dense), grain size 6–7 μm, with dielectric properties (at 4 GHz) of ɛ_r≈46, Q × f ≈38 000 GHz, and τ_f+13 ppm/°C, were studied at 25°–1300°C using synchrotron X-ray powder diffraction. At room temperature, CTLA exhibits a distorted orthorhombic structure, with two tilt systems: a =5.40383 (4) Å, b =5.41106 (6) Å, and c =7.64114 (7) Å with space group Pbnm . At 1050°±25°C, there is a transition from orthorhombic ( Pbnm ) to tetragonal ( I 4/ mcm ), with a simpler tilt arrangement. The lattice parameters at 1100°C were: a =5.44285 (4) Å and c =7.68913 (8) Å.     

Raman studies of peroxide formation,decomposition, and reduction on Ba/MgO

Ba/MgO is an active catalyst for the oxidative coupling of methane to form ethane and ethylene. It has been proposed that activation of methane occurs via reaction with peroxide species present at the surface of the catalyst. In the present work, Raman spectroscopy has been used to investigate the formation, decomposition, and reduction of BaO₂ on 4 mol% Ba/MgO. The presence of BaO₂ is evidenced by the presence of a band at 842 cm^–1. The peroxide forms above 300°C but is stable to decomposition at temperatures up to 500°C. Reduction of BaO₂ to BaO proceeds via Ba(OH)₂. BaCO₃ forms when either BaO or BaO₂ is exposed to CO₂. Once formed, BaCO₃ is stable to decomposition in He or O₂ at temperatures up to 500°C. Only BaCO₃ is observed when a mixture of CH₄ and O₂ is passed over the catalyst at 500°C.     

Effects of metal-support interactions on the synthesis of methanol over palladium

The synthesis of methanol and other products from CO and H₂ was studied over Pd catalysts prepared by adsorption of Pd(π-C₃H₃)₂ on MgO, ZnO, La₂O₃, γ-Al₂O₃, SiO₂, TiO₂, and ZrO₂ as well as over a SiO₂-supported Pd catalyst prepared from PdCl₂ and Pd black. Both the activity and selectivity of Pd were affected strongly by the nature of the support and the composition of the Pd precursor. The specific activity for methanol synthesis decreased in the order $\text{Pd}\text{La}{}_2\text{O}{}_3$ ? $\text{Pd}\text{SiO}{}_2$ [derived from PdCl₂] > $\text{Pd}\text{ZrO}{}_2$ > $\text{Pd}\text{ZnO}\text{≈}\text{Pd}\text{MgO}$ > PdTiO₂ > $\text{Pd}\text{Al}{}_2\text{O}{}_3\text{≈}\text{Pd}\text{SiO}{}_2$ [derived from Pd(π-C₃H₅)₂] ? Pd black, while the specific activity for hydrocarbon synthesis decreased in the order $\text{Pd}\text{TiO}{}_2\text{?}\text{Pd}\text{ZrO}{}_2$ > $\text{Pd}\text{La}{}_2\text{O}{}_3$ > $\text{Pd}\text{Al}{}_2\text{O}{}_3\text{≈}\text{Pd}\text{SiO}{}_2$ [derived from PdCl₂] ? $\text{Pd}\text{SiO}{}_2$ [derived from Pd(π-C₃3H₅)₂] ≈ Pd black ? $\text{Pd}\text{MgO}\text{?}\text{Pd}\text{ZnO}$. Dimethyl ether production was observed over four of the catalysts and the activity for formation of this product decreased in the order $\text{Pd}\text{Al}{}_2\text{O}{}_3\text{?}\text{Pd}\text{TiO}{}_2\text{?}\text{Pd}\text{MgO}\text{≈}\text{Pd}\text{ZrO}{}_2$. The effects of support composition on the catalytic properties of Pd are discussed in the light of current ideas concerning metal-support interactions and the acid-base properties of the support.     

The influence of oxygen vacancies on piezoelectricity in samarium-doped Pb(Mg1/3Nb2/3)O3-PbTiO3 ceramics

A study of 0.71Pb(Mg_1/3Nb_2/3)O₃-0.29PbTiO₃ shows that, when it is doped with 2.5% Sm on the A-site, in addition to an almost threefold increase in piezoelectric charge coefficient and dielectric permittivity, there is a 2 order of magnitude reduction in conductivity, attributed to a decrease in oxygen vacancy concentration. An analysis of the nonlinearity of permittivity with respect to field amplitude shows that both the reversible and irreversible contributions increase significantly with Sm-doping, with simple models showing that these changes are consistent with a reduction in the concentration of dipolar defects that can inhibit both polarization rotation and domain wall translation. Contrary to the argument that doping increases heterogeneity, there is little change in the diffuseness of the peak in permittivity as a function temperature, whilst there is a 15% increase in spontaneous polarization with Sm addition. Through comparison of the Rayleigh law parameters with those published for other piezoelectric materials, it is concluded that a significant contribution to the observed increase in piezoelectric performance due to Sm-doping of PMN-PT is similar in origin to that seen in soft, donor-doped PZT and other conventional piezoelectric ceramics.