基于逻辑器件的可编程增益放大器设计

本文介绍了可编程增益放大器设计的方法。它主要由控制电路、放大电路、显示电路三大模块组成。该系统性能好、成本低、工作可靠,具有一定的工程应用价值,经测试表明,该设计基本上达到了设计的要求。     

Eco‐friendly durable press finishing of cellulose‐containing fabrics

To impart easy‐care properties to cellulose‐containing fabrics along with avoiding any harmful effects of formaldehyde on both the health and the environment, attempts have been made to use citric acid (CA) as an ester crosslinking agent along with different catalytic systems in the absence and presence of certain additives. Further, fixation conditions, type of crosslinking agent, as well as type of substrate have been studied. Results revealed that the enhancement in carboxyl content, performance properties, and the decrease in tear strength (TS) as well as in whiteness indices (WI) of the finished fabric samples were increased by increasing CA concentration up to 80 g/L and by raising thermofixation temperature from 140 up to 180°C for 90 s. Inclusion of triethanolamine hydrochloride (TEA. HCl), decreased the carboxyl content, TS, color strength K/S, as well as oily stain release rating (SRR) of the finished fabric samples along with an increase in bound nitrogen (%N), wrinkle recovery angle WRA, and an improvement in WI without affecting the durable press rating (DP). Within the range examined (0–30 g/L), increasing PEG‐600 concentration improved the wet resiliency, TS, as well as WI properties of the finished samples. Increasing DMDHEU ratio in the CA/DMDHEU crosslinking system gave rise to an increase in %N, WRA (dry and wet), DP, as well as in free CH₂O of finished fabrics, along with a slight improvement in WI values. On the other hand, the TS, carboxyl content, K/S, SRR values of the finished fabric samples were lower at a higher DMDHEU ratio. Increase in carboxyl content, %N, WRA (dry and wet), DP and SRR, as well as extent of post dyeing (K/S) of the treated fabric samples upon using different ester crosslinking agents followed the descending order: citric acid > pyromellitic dianhydride. The opposite holds true for the TS, and WI values. Among the esterifying catalysts used, and for a given set of finishing conditions, NaH₂PO₂ · H₂O proved to be the most effective one, and the following order of effectiveness may be drawn: NaH₂PO₂ · H₂O > K₂HPO₄ > Na₃–citrate > Na₂–tartrate. Inclusion of silicone softener in the finishing formulation brought about an improvement in softeness degree, WRA, %N, DP, TS as well as K/S values along with a decrease in carboxyl content, SRR, and WI values of the treated fabric samples, regardless of the used silicone softener.The performance properties of the finished fabric samples were determined by the type and nature of the substrate. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2243–2253, 2002     

Synthesis,characterization, and thermal properties of phosphorus‐containing,wholly aromatic thermotropic copolyesters

A series of phosphorus‐containing, wholly aromatic thermotropic copolyesters from acetylated 2‐(6‐oxide‐6H‐dibenz〈c,e〉〈1,2〉oxa phosphorin‐6‐yl)‐1,4‐dihydroxy phenylene, p‐acetoxybenzoic acid, terephthalic acid, and isophthalic acid were prepared by melting polycondensation. The structure and basic properties of the polymers, such as the glass‐transition temperature (T_g), melting temperature (T_m), thermal stability, crystallinity, and liquid crystallinity, were investigated with Fourier transform infrared, elemental analysis, differential scanning calorimetry (DSC), thermogravimetric analysis, wide‐angle X‐ray diffraction, and hot‐stage polarizing optical microscopy. The copolyesters had relatively high T_g values ranging from 183 to 192°C. The T_m values obtained from DSC curves for samples P‐20 and P‐25 were 290 and 287°C, respectively (where the number in the sample name indicates the molar fraction of the phosphorus‐containing monomer in the reactants). The initial flow temperatures of other samples observed with hot‐stage polarizing microscopy were 271–290°C. The 5% degradation temperatures in nitrogen ranged from 431 to 462°C, and the char yields at 640°C were 41–52%. All the copolyesters, except P‐40, were thermotropic and nematic. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1278–1284, 2002     

Antimicrobial protection of cotton and cotton/polyester fabrics by radiation and thermal treatments. I. Effect of ZnO formulation on the mechanical and dyeing properties

Cotton and cotton/polyester fabrics were treated against microbial attack by applying a formulation based essentially on ZnO under high‐energy radiation and thermal curing. To achieve the homogeneity and the reactivity of the treating formulation, a binder (Impron MTP) and a dispersing agent (Setamol WS) were used with ZnO. The antimicrobial property of the fabrics was evaluated, in terms of mechanical properties, by a soil burial test. Moreover, the effect of antimicrobial finishing on the dyeing properties in terms of color strength was investigated. It was found that the best composition that affords the best antimicrobial protection to cotton fabrics contains 2% ZnO, 2% binder, and 1% dispersing agents. For the cotton/polyester blend, the best results were achieved at the same conditions except the ZnO was 1%. It was found that the treatment under the effect of electron‐beam irradiation is better than that of gamma irradiation and thermal curing. The results showed that when the finishing process was carried out before dyeing with a reactive dye, it affects the color strength rather than performing the finishing after the dyeing process. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1129–1137, 2003     

Modification of leather properties by grafting. I. Effect of monomer chain on the physico‐mechanical properties of grafted leather

Although leather has a number of desirable properties such as thermal stability and fire retardancey, in addition to high toughness, it has a few drawbacks such as weight, high water absorption, poor soil and rot resistance, and nonuniformity. If these defects are overcome, leather's usefulness would be further enhanced and its competitive position with respect to synthetics would increase. This study reports the physical and mechanical properties of buffalo leather after chemical graft copolymerization with ethyl acrylate, butyl acrylate, and 2‐ethyl hexyl acrylate using benzoyl peroxide as an initiator. The optimum conditions for grafting (e.g., monomer and initiator concentrations, temperature and time of grafting, and solvent leather ratio) were extensively investigated. The study achieved outstanding properties for buffalo leather in reduction of water uptake after grafting, especially on using 2‐ethyl hexyl acrylate and butyl acrylate monomers. FT‐IR and solid ¹³C‐NMR for leather before and after grafting confirmed the grafting process.© 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1478–1483, 2003     

Modeling the large‐strain constitutive behavior of polycarbonate under isothermal and anisothermal conditions

The tensile behavior of polycarbonate was studied at large strains below the glass‐transition temperature. Experiments were carried out at a series of constant temperatures and also under conditions of falling temperatures. The specimens necked with a natural draw ratio of approximately 2, and the study was mainly focused on the necked material. Isothermal experiments revealed an elastic mechanism that initiated beyond the natural draw ratio. A model consisting of an Eyring process and two Gaussian elastic mechanisms was found to be applicable to both the isothermal and anisothermal stress‐relaxation and stress–strain results. The same model also produced reasonable estimates of the stresses generated during the necking process. In addition, a simple relationship between the isothermal and anisothermal stress relaxation was demonstrated. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2105–2116, 2005     

用于光纤并带的UV固化胶粘剂性能的研究

研究了用于光纤带的紫外光固化胶粘剂的剥离性、柔韧性、拉伸强度和延伸率的影响因素。     

Preparation,characterization, and some physical properties of polypropylene/poly(methyl acrylate)‐grafted glass wool composites

Polypropylene/poly(methyl acrylate)‐grafted glass wool (PMA‐g‐GW) mixes were prepared. The polymerization process was carried out using potassium persulfate (PPS) and PPS/acetone sodium bisulfite (ASBS) as a redox‐pair initiation system at 60 and 70°C. The effect of using PPS or PPS/ASBS on the grafting percent and conversion percent reveals that the conversion percent values on using PPS as an initiator are higher than those of PPS/ASBS, while in the case of grafting, the inverse is true, that is, using PPS as an initiator gives grafting percent values lower than those that can be obtained using PPS/ASBS. The dielectric properties, thermal diffusivity, specific heat capacity, and thermal conductivity of PP loaded with modified glass wool as a function of different types and concentrations of initiators—used in the grafting polymerization process, namely, PPS and the redox initiating system—were also studied. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 723–732, 2003     

Monodisperse polymer/metal composite particles by electroless chemical deposition: Effect of surface functionality of polymer particles

Micron‐sized polymer particles were coated with layers of nickel compounds by plating electrolessly in the presence of aqueous solutions of nickel chloride, sodium hypophosphite, sodium citrate, and ammonium chloride at elevated temperature. The uniform functional polymer particle could be obtained by seeded polymerization. To investigate the effect of surface functionality on the conditions for nickel deposition, the polymer particle was functionalized with the thiol group. From morphological observation, it was found that the mode of nickel deposition was greatly dependent on the surface functionality of the polymer particle. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 420–424, 2003