LiNbO3 optical waveguides formed in a new proton source

Proton-exchanged planar waveguides have been fabricated on Z-cut and X-cut lithium niobate crystals by using a new proton source formed by a mixture of benzoic and adipic acids. Waveguide index profiles and optical characteristics have been obtained at different values of the adipic-benzoic acid concentration ratio. The samples have been structurally characterized by Raman and infrared (IR) absorption spectroscopy and double-crystal X-ray diffraction. Good quality samples have been fabricated by using 30 mol% ratio dilution, showing very low scattering levels (<0.1 dB/cm), relatively high electrooptic coefficient (r₃₃=0.88 pm/V), and low relative percentage of interstitial protons (26%). The main factor limiting the waveguide optical properties is the substitutional-interstitial proton ratio, which can be easily controlled to produce good quality waveguides. A demonstration of the repeatability of the exchange process in the acid mixture is also provided     

A base-band NDS electrode configuration for HACT devices

Heterostructure Acoustic Charge Transport (HACT) devices have been fabricated with a new nondestructive sense (NDS) electrode structure that provides for the recovery of base-band signals without the use of an integrating capacitor. This electrode structure provides an output signal comprising an RF carrier at the SAW frequency, amplitude modulated by the sampled input signal which has been delayed by a period proportional to the output electrodes distance from the input diode. The output of the NDS electrode structure is subsequently demodulated to provide the base-band signal     

Suppression control method for torque vibration of three-phase HB-type stepping motor utilizing feedforward control

This paper proposes a method to reduce the vibration of the three-phase HB-type stepping motor with cogging torque by the feedforward compensation control. The compensation signal to suppress the vibration of the motor frame is obtained by the repetitive controller installing an online Fourier transformer and utilizing an acceleration sensor attached to the motor frame or an acoustic sensor such as a microphone placed close to the frame. The sensor is used only for the acquisition of the feedforward compensation data. The feedforward compensation signal at an arbitrary operating point is derived from the amplitude and phase data of the frequency components and the operating point data. Compensation data obtained by the repetitive controller is applied to the operating point changed by reference frequency and load condition in steady state. The compensation signal for the new operating point will be generated from compensation data utilizing polynomial equation approximation and linear interpolation method. The effectiveness of this proposed method is confirmed by the experimental results.     

Increasing the service properties of weld joints by electrohydroimpulse treatment

Known examples of the positive influence of electrohydroimpulse treatment on the quality of weld joints of various steels, particularly including an increase in their long-term and cyclic strength and also corrosion resistance, are analyzed. It is shown that in this case there is a reduction in residual macro- and micro-stresses and also a change in the parameters of the dislocation structure of the joint metal in the direction of stabilization of it.Translated from Problemy Prochnosti, No. 4, pp. 119–123, April, 1996.     

Aperture sampling requirements in planar near-field and patterncalculations

The paper covers a simple idea. If we sample an aperture, we can obtain valid patterns over a limited angular region about the normal to the aperture. The same expression can be used with near-field measurements. I reduced the expression to a nomograph. A nomograph allows one to rapidly test various choices. In the second half of the paper, I answer questions caused by the February column which discussed polarization (Milligan, IEEE Antennas. Propag. Mag., vol.38, no.1, p.56-8, 1996)     

Experimental estimate of self-irradiation of building bricks due to incorporated radionuclides

A method is described for experimentally determining the dose rate created in building bricks by incorporated natural radionuclides. It was established using the thermoluminescence dosimetry method that the measured dose rate depends on the detector thickness, the mass of the ceramic product investigated, and the irradiation geometry. The contributions to the measured dose of weakly penetrating α and β radiation and hard ψ radiation are separated, the ratio between them depending on the experimental conditions. Translated from Izmeritel'naya Tekhnika, No. 7, pp. 62–66, July, 1996.     

Perinatal problems and the prevention of premature labor]

The article describes the experience of implementing patient-focused care from a physician's perspective. Pitfalls that guarantee failure are presented, many of which are avoidable with early participation by all parties involved: administrators, nursing staff, physicians, and patients. Contamination of the process with downsizing needs, lack of support for staff in dealing with necessary change, loss of administrative commitment, and withholding of appropriated funds are among the key errors to be avoided.