Structure and gas permeation properties of asymmetric polyimide membranes made by dry–wet phase inversion: Influence of the polyimide molecular weight

In this article, we report the influence of the polyimide molecular weight (1.2 × 10⁵, 2.6 × 10⁵, and 4.1 × 10⁵) on the structure and the gas permeation properties of asymmetric polyimide membranes made by the dry–wet phase‐inversion process. The apparent skin layer thickness of the asymmetric membrane increased with increasing molecular weight, and the thicknesses of the membranes prepared from the three polyimides with a casting polymer solution containing 8.0 wt % butanol were 132, 350, and 739 nm, respectively. That is, the gas permeance in the asymmetric membranes increased with decreasing molecular weight. In contrast, the gas selectivity of the asymmetric membranes did not depend on the skin layer thickness. The solvent evaporation in the dry phase‐inversion process and the nonsolvent diffusion in the dry process were important factors that determined the formation of the asymmetric membrane. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Advanced energy saving in the reaction section of the hydro-desulfurization process with self-heat recuperation technology

The reaction section of the naphtha hydro-desulfurization (HDS) process is a heating and cooling thermal process consisting of a feed/effluent heat exchanger and a fired heater. Energy savings are fundamentally made as a result of the maximized heat recovery in the heat exchanger and the reduced heat duty of the fired heater. To achieve further energy saving in the process, “self-heat recuperation technology” (SHRT) was adopted. In this technology, a compressor was introduced. The suction side of the compressor needed a lower pressure and the feed stream evaporated much easily. The discharged side of the compressor satisfied the operating conditions of both pressure and temperature at the inlet of the reactor. And the reactor effluent stream was able to be used completely to preheat and vaporize the feed stream. All the heat in the process stream was re-circulated without using a fired heater. SHRT was applied to the naphtha HDS process of 18,000 barrel per stream day (BPSD) in the refinery and the mass and energy balance of the process was calculated using commercially available simulation software, Invensys PROII version 8.1. This process-simulation case study confirmed that despite there being no more energy saving potential in the conventional process that makes use of a fired heater, the advanced process with SHRT can reduce the energy consumption significantly by using the recuperated heat of the feed stream.     

A quantum chemical study on the polycondensation reaction of polyesters: The mechanism of catalysis in the polycondensation reaction

We carried out a theoretical study on the mechanism of catalysis in the poly(ethylene terephthalate) (PET) polycondensation reaction. Transesterification reaction of diethylterephthalate with ethanol is investigated as a model system by using the B3LYP level of theory, and Sb(OEt)₃, Ge(OEt)₄ and Ti(OEt)₄ are adopted as model catalysts. We found that the metal center of metal alkoxides coordinates to the carbonyl oxygen atom of the ester, and the alkoxy oxygen atom of alkoxy ligands attacks to the carbonyl carbon atom of the ester to form the four-centered transition state. The activation energy for tetraethoxy titanium catalyzed reaction in vacuo is 15.47 kcal/mol; this is comparable to the experimental result of 11.2 kcal/mol for poly(butylene terephthalate)/Ti(OBu)₄. Because the other mechanisms gave much higher activation energies, this is the most convincing mechanism of PET polycondensation catalysis by antimony, germanium and titanium alkoxides.     

Super environment-friendly electrodeposition paint

Super low VOC due to new composition/reaction mechanism can minimize the environmental risk as it does not contain lead and tin, hazardous air pollutants (HAPs) and endocrine disrupters (EPA/67 items, SPEED’98/JEA/67 items) currently specified as contaminants. New EAD (electrolyzed activate deposition paint) is not the only conventional cure agent or solvent, but also the super low VOC, HAPs materials and endocrine disrupters. The electric energy used by EAD is utilized for the reaction but not for the deposition. EAD consists of two technologies. One is propargyl group change to the allene by using electrodeposition. Propargyl group is stable, but allene group is highly polymerizing. As a result, EAD had high bath stability. The other is sulfonium change to sulfide by using electrodeposition. This sulfonium salt is lost as a result of the electrolytic reduction, and hence can be irreversibly rendered non-conductive. As a result, EAD showed high throwing power.     

An innovative modularity of heat circulation for fractional distillation

A novel modularity of heat circulation for distillation process, which reduces the energy consumption, is proposed. By incorporating compressors and heat exchangers, the heat of the distillate is recuperated and exchanged with the heat of the feed streams. The proposed technology achieves the reduction in the required energy more than 75% as compared with a benchmark process which uses external heat source for heating. This shows the proposed modularity of heat circulation for distillation process is very promising technology to drastically reduce energy demand for distillation.     

Substance P- and calcitonin gene-related peptide-containing nerve fibers in the nasal mucosa of chronically hypoxic rats

Changes made in 1997 and 1998 in the U.S. childhood immunization schedule are discussed, with a focus on the use of poliovirus, pertussis, and combination vaccines. Oral poliovirus vaccine (OPV), the vaccine of choice for all four doses in the polio immunization series since 1962, can cause vaccine-associated paralytic poliomyelitis (VAPP). The inactivated poliovirus vaccine (IPV) has not been associated with VAPP but must be administered by injection and provides inferior intestinal immunity. With the reduced threat of poliovirus importation into the United States, the risk of VAPP, although low, has become less acceptable. The Centers for Disease Control and Prevention accordingly recommended a shift from OPV to IPV in the childhood immunization schedule for the United States, effective January 1997. A sequential OPV and IPV series is recommended, but the schedule includes an OPV-only option, which may be preferred in order to avoid the required injections, and an IPV-only option, which is recommended for immunocompromised persons and their contacts. Concern over local and systemic reactions associated with whole-cell pertussis vaccines, in addition to controversy over a possible relationship between the whole-cell vaccine and neurologic damage, has led to the development of new diphtheria and tetanus toxoids and acellular pertussis vaccine products for use in the diphtheria and tetanus toxoids and pertussis immunization series. Several combination products were licensed in 1997, and more are on the way. This will mean fewer inoculations for children. Increased use of IPV and acellular pertussis products could reduce the frequency of VAPP due to OPV and the local and systemic reactions associated with whole-cell pertussis vaccine.     

LES analysis of flow and turbulent mixing in an unsteady jet

The flow and mixing process of unsteady jets are fundamentally analyzed by large eddy simulations. The effects of nozzle velocity and turbulence intensity on the turbulent eddy structure and mixing process between the nozzle fluid and ambient fluid were investigated. The results show that a toroidal‐shaped vortex, which emerges around the jet tip, primarily accelerates the entraining flow. Also, increasing the turbulence intensity in the nozzle encourages mixing in the jet without changing the jet‐contour. Furthermore, when the rise‐up time of the initial nozzle velocity is elongated, turbulent mixing is suppressed. © 2007 Wiley Periodicals, Inc. Heat Trans Asian Res, 36(5): 303–313, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20158     

a-SiC:H/SiO2 Laminated Polarization Splitter for the Wavelength Region Longer Than 1.3 μm Prepared by Plasma-Enhanced Chemical Vapor Deposition

A laminated polarization splitter for the wavelength region longer than 1.3 μm is fabricated for the first time. It is composed of a-SiC:H/SiO₂ alternative multilayers prepared by plasma-enhanced chemical vapor deposition. Splitting behavior is also verified experimentally. It has low absorption loss even for the wavelength region around λ = 1.3 μm because the band-gap energy of a-Sic is larger than that of a-Si. The measured splitting angle is 13.8°, which is 2.4 times larger than the 5.7° splitting angle of rutile. The absorption loss of the multilayer is reduced to 1 × 10^-3 dB/μm at λ = 1.3 μm. The magnitude of the residual stress is 9.45 × 10⁸ dyn/cm², which is about one-third of that prepared by the rf bias sputtering equipment which is used for another project of our group. The deposition rate of SiO₂, is increased to 135 nm/min, which is 27 times larger than that prepared by the sputtering equipment.     

Effect of a plated Fe-Cr-Ni alloy layer for rapid nitriding of invar

The nitriding rate in a plated invar with an Fe-Ni-Cr alloy (face-centred cubic) layer were compared by optical microscopy with the rate in an unplated invar. In the plated invar rapid nitrogen diffusion was discovered. The plated layer plays a role in enhancing the nitriding rate. The result gives a solution for an abnormal enhancement nitriding rate in austenitic stainless steels. The enhancement is explained from the viewpoint of non-equilibrium thermodynamics.     

Expression of prolactin gene in mouse placenta during late pregnancy: detection of mRNA and its translation product

Threshold photoelectron spectra of N2+ were measured between 23.4 and 27.6 eV with high resolution and high intensity by using the penetrating field technique and synchrotron radiation. Five vibrational progressions were observed. The first of these progressions was the C2Sigmau+ state. The second progression was identified as the transition to the second state of 2Pig symmetry found by P. Baltzer, M. Larsson, L. Karlsson, B. Wannberg, and M. Carlsson (1992. Phys. Rev. A 46, 5545). The third progression, which was discovered by F. Merkt and P. M. Guyon (1993. J. Chem. Phys. 99, 3400), can be designated as the 2Sigmau- state by comparison with previous theoretical study (E. W. Thulstrup and A. Andersen, 1975. J. Phys. B 8, 965). The fourth and fifth progressions were designated as the 2Deltau and 2(2) Piu states by similar comparison with previous theories. Copyright 1997 Academic Press. Copyright 1997Academic Press