Investigation of thermal residual stresses during laser ablation of tantalum carbide coated graphite substrates using micro-Raman spectroscopy and COMSOL multiphysics

Laser ablation of high-temperature ceramic coatings results in thermal residual stresses due to which the coatings fail by cracking and debonding. Hence, the measurement of such residual stresses during laser ablation process holds utmost importance from the view of performance of coatings in extreme conditions. The present research aims at investigating the effect of laser parameters such as laser pulse energy, scanning speed and line spacing on thermal residual stresses induced in tantalum carbide-coated graphite substrates. Residual stresses were measured using micro-Raman spectroscopy and correlated with Raman peak shifts. Transient thermal analysis was performed using COMSOL Multiphysics to model the single ablated track and residual stresses were reported at low, moderate and high pulse energy regimes. The results showed that the initial laser conditions caused higher tensile residual stresses. Moderate pulse energy regime comprised higher compressive residual stresses due to off centre overlapping of the laser pulses. Higher pulse energy (250 μJ), higher scanning speed (1000 mm/s) and moderate line spacing (20 μm) caused accumulation of tensile residual stresses during the final stage of laser ablation. The deviation of experimental residual stresses from COMSOL numerical model was attributed to unaccounted additional stresses induced during thermal spraying process and deformation potentials in the numerical model.     

QoS-Aware Optical Fog-Assisted Cyber-Physical System in the 5G Ready Heterogeneous Network

Wireless Personal Communications - In recent years, the emergence of Internet of things and cyber-physical system provide a proactive and efficacious solution to enable remote monitoring, machine...     

Efficient watermarking technique for protection and authentication of document images

Multimedia Tools and Applications - In this paper, a hashing based watermarking technique for the protection and authentication of document image is proposed. Message Digest 5 (MD5) hashing is...     

Structural,optical and electronic characteristics of Cu and Mg-doped nano MnS sample prepared by molten salt solid state reaction

Journal of Materials Science: Materials in Electronics - Nano Mn0.95M0.05S (M ≡ Cu, Mg) samples were produced using molten salt solid state reaction method. Rietveld analysis of X-ray...     

Magnetically Modified Waste Bark of Aegle marmelos Tree as a Promising Biosorbent for Uranium(VI) Sorption

Radiochemistry - Magnetically modified waste bark of the Aegle marmelos tree was prepared by using green synthesis method and was used in a batch system for U(VI) removal from aqueous solution. The...     

Two-step sinter-crystallization of K2O–CaO–P2O5–SiO2 (45S5-K) bioactive glass

Bioactive glasses and glass-ceramics (GCs) effectively regenerate bone tissue, however most GCs show improved mechanical properties. In this work, we developed and tested a rarely studied bioactive glass composition (24.4K₂O-26.9CaO-46.1SiO₂-2.6P₂O₅ mol%, identified as 45S5-K) with different particle sizes and heating rates to obtain a sintered GC that combines good fracture strength, low elastic modulus, and bioactivity. We analyzed the influence of the sintering processing conditions in the elastic modulus, Vickers microhardness, density, and crystal phase formation in the GC. The best GC shows improved properties compared with its parent glass. This glass achieves a good densification degree with a two-step viscous flow sintering approach and the resulting GC shows as high bioactivity as that of the standard 45S5 Bioglass®. Furthermore, the GC elastic modulus (56 GPa) is relatively low, minimizing stress shielding. Therefore, we unveiled the glass sintering behavior with concurrent crystallization of this complex bioactive glass composition and developed a potential GC for bone regeneration.     

Influence of Al3+ doping for V5+ on the structural,optical, thermal and electrical properties of V2-xAlxO5-δ (x=0–0.20) ceramics

This paper reports an investigation on the structure-properties correlation of trivalent metal oxide (Al₂O₃)-doped V₂O₅ ceramics synthesized by the melt-quench technique. XRD patterns confirmed a single orthorhombic V₂O₅ phase formation with increasing strain on the doping of Al₂O₃ in place of V₂O₅ in the samples estimated by Williamson-Hall analysis. FTIR and Raman investigations revealed a structural change as [VO₅] polyhedra converts into [VO₄] polyhedra on the doping of Al₂O₃ into V₂O₅. The optical band gap was found in a wide semiconductor range as confirmed by UV–visible spectroscopy analysis. The thermal and conductivity behavior of the prepared samples were studied using thermal gravimetric analysis (TGA) and impedance analyzer, respectively. All the prepared ceramics exhibit good DC conductivity (0.22–0.36 Sm^-1) at 400 ?C. These materials can be considered for intermediate temperature solid oxide fuel cell (IT-SOFC)/battery applications due to their good conductivity and good thermal stability.     

Motion of a Robot Mower with Directional Control

Russian Engineering Research - The stability of robot-mower motion in a specific direction is considered. The direction is regulated by means of an angular sensor and a programmable controller...     

Calcium deficient hydroxyapatite by precipitation: Continuous process by vortex reactor and semi-batch synthesis

Precipitation of calcium deficient hydroxyapatite nanoparticles in an environmentally benign manner by using only dilute solutions of calcium hydroxide and phosphoric acid without pH adjustment and addition of other chemicals, and water, being the only by-product was investigated by using continuous flow Vortex Reactor (VR) and Semi-Batch Reactor (SBR). The effect of hydrodynamics by changing the Reynolds number of the jets providing residence times of 8.4 ms to 4.37 s for VR, and by changing the stirrer speed between 100 rpm (Re = 2656) and 1000 rpm (Re = 26560) for SBR, on the particle size, particle size distribution, and morphology of the particles was investigated for both systems. It has been shown that it is possible to produce pure phase hydroxyapatite nanoparticles in the desired morphology by changing production system, without resorting to additives. While VR produced rod-like particles with the crystallite size around 4 nm, SBR produced spherical particles with the crystallite size of around 5 nm.     

The role of microstructural evolution during spark plasma sintering on the soft magnetic and electronic properties of a CoFe–Al2O3 soft magnetic composite

Journal of Materials Science - For transformers and inductors to meet the world’s growing demand for electrical power, more efficient soft magnetic materials with high saturation magnetic...