Zn-Al系二元相图的研究

利用高温X射线衍射法（XRD）、示差扫描量热分析法（DSC）、热膨胀法（PRD）等方法重新测定Zn-Al二元体系相图。在XRD曲线图中β（ZnAl）相的存在，表明存在β（ZnAl）固溶单相区；DSC曲线图表明在274～279℃范围内存在共析相变反应；PRD曲线图表明在340℃不存在相变反应。综合XRD、DSC和PRD结果，绘制了部分Zn-Al二元体系相图，为高铝锌基合金的实际相变应用提供参考。     

Study on the graphite nanosheets/resin shielding coatings

Shielding coatings based on graphite nanosheets were prepared by compounding method. The surface morphology of the graphite nanosheets and conductive coatings was examined by scanning electron microscopy. The surface resistivity of the coatings was greatly declined by incorporating the graphite nanosheets. The electromagnetic interference shielding effectiveness (SE) from 0.3 MHz to 1.5 GHz was also studied, and found that the SE of the coatings was consistent with its conductivity. The best sample was shown to exhibit up to 38 dB of SE at 1.5 GHz (with a thickness of 400 μm). The main shielding mechanism of the system was reflection and multiple reflections.     

Thermogravimetric analysis of chitosan

The thermal degradation of chitosan at different heating rates B in nitrogen was studied by thermogravimetric analysis. The results indicate that the thermal degradation of chitosan in nitrogen is a one‐step reaction. The degradation temperatures increase with B. Experimentally, the initial degradation temperature (T₀) is (1.049B + 326.8)°C; the temperature at the maximum degradation rate, that is, the peak temperature on a differential thermogravimetry curve (T_p), is (1.291B + 355.2)°C; and the final degradation temperature (T_f) is (1.505B + 369.7)°C. The degradation rates at T_p and T_f are not affected by B, and their average values are 50.17% and 72.16%, respectively, the maximum thermal degradation reaction rate, that is, the peak height on a differential thermogravimetry curve (R_p), increases with B. The relationship between B and R_p is R_p = (1.20B + 2.44)% min^?1. The thermal degradation kinetic parameters are calculated with the Ozawa–Flynn–Wall method. The reaction activation energy (E) and frequency factor (A) change with an increasing degree of decomposition, and the variable trends of the two kinetic parameters are similar. The values of E and A increase remarkably during the initial stage of the reaction, then keep relatively steady, and finally reach a peak during the last stage. The velocity constants of the thermal degradation vary with the degree of decomposition and increase with the reaction temperature. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

TC4钛合金高转速惯性摩擦焊接头组织及性能分析

采用高转速(3500～4300 r/min)惯性摩擦焊方法焊接TC4钛合金,观察了不同焊接工艺条件下焊接接头的显微组织,讨论了高转速条件下惯性摩擦焊接接头组织的形成机理,分析了焊接接头的性能.结果表明,TC4钛合金惯性摩擦焊焊接接头的形状呈"V"字型,焊缝区和热影响区的组织特征与低转速条件下的显微组织一致.焊缝组织沿径向变化,心部为细小的等轴晶,向外逐渐过渡为片状组织;焊缝区的硬度高于母材和热影响区;接头拉伸试样断裂于母材.     

轮胎成型机供料架气动系统的改进

通过对轮胎成型机中带束层供料架摆架气动回路的修改，解决了以往摆架在下落时的冲击现象。此原理适用于所有负载不均衡的工况。本文详细阐述了摆架部分多种气动原理及其改进办法。     

ABA triblock copolymers from poly(p‐dioxanone) and poly(ethylene glycol)

Poly(p‐dioxanone)–poly(ethylene glycol)–poly(p‐dioxanone) ABA triblock copolymers (PEDO) were synthesized by ring‐opening polymerization from p‐dioxanone using poly(ethylene glycol) (PEG) with different molecular weights as macroinitiators in N₂ atmosphere. The copolymer was characterized by ¹H NMR spectroscope. The thermal behavior, crystallization, and thermal stability of these copolymers were investigated by differential scanning calorimetry and thermogravimetric measurements. The water absorption of these copolymers was also measured. The results indicated that the content and length of PEG chain have a greater effect on the properties of copolymers. This kind of biodegradable copolymer will find a potential application in biomedical materials. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:1092–1097, 2006     

Crystal morphology and tensile properties of LLDPE containing PP fibers as obtained via dynamic packing injection molding

The fibrillated linear low-density polyethylene (LLDPE)/isotactic polypropylene (iPP) fiber blends were subjected to dynamic packing injection molding (DPIM), in which the prolonged shear was exerted on the melt during solidification stage. Transcrystallization of LLDPE on PP fibers, with stacked lamellae parallel to each other and aligned approximately perpendicular to the long axial of the fibers, has been achieved for the first time in DPIM due to the prolonged shear. PP fibers were found to align parallel to the flow direction along thickness up to the oriented zone of sample prepared by DPIM. The presence of oriented PP fibers enhanced the orientation of LLDPE that developed row-nucleated type morphology. The molding temperatures were changed between 160 °C and 200 °C to investigate the effect of molding temperature on the crystalline microstructure of the blends. As increasing the molding temperature from 160 °C to 200 °C, the partial melting of PP fiber was changed to complete melting, resulting in a dramatic change of the crystal morphology and the mechanical properties as well.     

氨纶氯水降解及耐氯机理的探讨

应用红外光谱分析方法，对氨纶（ＰＵ纤维）氯水降解及耐氯机理进行了初步的研究。结果表明，ＰＵ浸氯水后，因受活性氯原子的攻击，ＰＵ大分子软链段的碳－碳键发生断裂，形成碳－氯化合物，添加剂加入后，因与ＰＵ大分子的软链段形成螯合物，从而避免了活性氯原子的攻击，有效地保护了软链段，使氨纶耐氯性能明显改善。     

电容器浸渍剂的催化合成研究

研究了以甲苯、氯化苄为原料合成苄基甲苯的工艺，进行了催化剂的选择和研制、工艺条件试验、单苄基和双苄基甲苯比例的控制试验及复配制成Ｃ１０ｌ浸渍剂等项工作。获得了较佳的工艺条件，收率达９３％以上。试验样品作为高压全膜电容器用浸渍剂，性能达到国际同类产品水平。     

直接凝固注模成型Si_3N_4及SiC陶瓷──基本原理及工艺过程

直接凝固注模成型（ｄｉｒｅｃｔｃｏａｇｕｌａｔｉｏｎｃａｓｔｉｎｇ，ＤＣＣ）是一种崭新的（准）净尺寸陶瓷成型方法。本文报道了采用此法成型Ｓｉ_３Ｎ_４及ＳｉＣ陶瓷的基本原理和工艺过程。ＤＣＣ成型工艺过程为把高固相含量低粘度的陶瓷浆料浇注到无孔模具中，事先加入到浆料中的生物酶及化学物质通过改变浆料的ｐＨ或电解质浓度来改变浆料的胶体化学行为，从而使浆料原位凝固，得到有足够脱模强度的陶瓷坯体。ＤＣＣ成型的特点为坯体密度高（理论密度的５５％～７０％），坯体均匀，不用或只需少量的有机添加剂（少于１％），可成型大尺寸、复杂形状、高可靠性的陶瓷部件。