AADL 测试模型的构造研究

目前,结构分析和设计语言AADL在任务关键嵌入式系统领域有着良好的应用.为了保障任务关键软件的质量,文章提出基于AADL测试模型对AADL设计模型进行测试,以发现设计模型中存在的错误.研究给出了体现系统拓扑结构的AADL测试模型的形式定义及由AADL构造该测试模型的算法,基于该测试模型可以对AADL设计模型中构件交互的输入、输出端口序列和连接的正确性进行测试,并以飞行控制系统的AADL设计模型为例,阐释了研究成果.     

Non-Fourier heat conduction in a thin gold film heated by an ultra-fast-laser

Based on the dual-phase-lagging(DPL)heat conduction model,the Cattaneo-Vernotte(CV)model and the improved CV model we investigate the one-dimensional heat conduction in gold films with nano-scale thickness exposed to an ultra-fast laser heating.The influence of system parameters on the temperature field is explored.We find that for all the non-Fourier heat conduction models considered in this work,a larger Knudsen number normally leads to a higher temperature.For the DPL model,the large ratio of the phase lag of temperature gradient to the phase lag of heat flux reduces the maximum temperature and shortens the time for the system to reach its steady state.The CV model and the improved CV model lead to the similar thermal wave behavior of the temperature field,but the thermal wave speeds for these two models are different,especially for large Knudsen numbers.When the phase lag of temperature gradient is smaller,the difference between the DPL model and the improved CV model is not significant,but for the large phase lag of temperature gradient the difference becomes quite significant,especially for the large Knudsen number.In addition,the effect of the surface accommodation coefficient,which is a parameter in the slip boundary condition,on the temperature field of the gold film heated by ultra-fast laser pulses is investigated based on the DPL model.     

Oxidation behavior and mechanism of aluminum oxynitride (AlON) at elevated temperatures

The oxidation behavior and mechanism of aluminum oxynitride (AlON) powder exposed to air at elevated temperatures between 800°C and 1300°C was investigated by X-ray diffractometry (XRD), scanning electron microscope (SEM), electron spin resonance (ESR), nuclear magnetic resonance (NMR), and simultaneous thermogravimetry, differential thermal analysis, and mass spectrometry techniques (TG-DTA-MS). The weight of AlON gradually increases to a maximum value at 1150°C and then decreases with further heating. Meanwhile, AlON powder undergoes chemical changes, as evidenced by lattice expansion, and turns eventually into alumina. ESR spectra reveal the occurrence of lone pair electrons in the oxidized products and the intensity of corresponding resonance signal increases before disappearing with the increase in temperature. Combined with the results of NMR and TG-DTA-MS, the measured data suggest that Al-N in [AlO₃N] tetrahedron and [AlO₅N] octahedron are gradually oxidized into Al-O-N group with lone pair electrons, which causes continuous weight gain and lattice expansion. Further oxidation at higher temperatures results in alumina and N₂.     

Engineering all-aromatic polyamide surface from hydrophilic to superhydrophobic and the accelerated strategy

Being a new kind of nanomaterials, aromatic polyamide nanofibers (ANF) have been much highlighted in recent studies. We here demonstrate an isopropyl alcohol (IPA) accelerated chemical cleavage on poly (p-phenylene terephthalamide) chopped fibers, which provides an efficient preparation method of ANF. The comprehensive study on the processes accelerated by different alcohols revealed that the preparation time of ANF in the mixed medium of dimethyl sulfoxide (DMSO)-alcohol (20:1 in volume) was shorten to 45 min and 75 min for methanol (ethanol) and isopropanol, respectively. However, the nanofibers prepared in DMSO-IPA exhibited the minimum in axial and radial dimensions, providing the finest and most uniform diameter of 16 nm. The corresponding ANF films through vacuum assisted filtration also showed the highest tensile strength of 150 MPa, in comparison with those of the ANF films prepared using other alcohols, which were about 110 MPa. Furthermore, ANF/silicon hybrid films were prepared by the ionic ring-opening reaction followed by the alkoxysilane condensation and nanoparticle fabrication. By changing the organo functional groups in the alkoxysilane, the surface of the films were adjustable in a wide contact angle range from 56° (hydrophilic) to 150° (superhydrophobic), suggesting the amendable interfacial properties potential applicable to composite fabrication with most of the resin matrix.     

纳米金刚石的应用

纳米金刚石不仅具有金刚石所固有优异特性，而且还具有纳米材料所拥有的奇异性能。正是这些综合技术特性，使得它在传统的和新的技术领域中得到应用，并初见成效，本文从超精抛光、润滑、复合镀、磁性录音系统和医疗等方面的应用做了扼要的叙述，指出，纳米金刚石颗粒具有球形和准球形的特点，使得摩擦表面形成滚珠轴承效应，而表现出良好的润滑性，从而避免于摩现象的发生，而对一些主要因接触疲劳或高温磨损而失效的工件，纳米金刚石金属的复合涂层，则具有明显的优越性。     

双回转送进二辊冷轧管机凸轮设计研究

本文提出了双回转送进二辊冷轧管机凸轮理论轮廓曲线的新设计方法 ,其轮廓曲线加速度与跃度呈梯形 ,且跃度边界连续 ,给出了针对双回转送进二辊冷轧管机的两个过渡段具有等加速度和跃度的设计准则     

时效对接触线用Cu-Ag-Cr合金性能的影响

分析了固溶温度、时效及时效前冷变形量对Cu - 0 1 %Ag - 0 1 %Cr接触线用合金性能的影响 ,结果表明 :经 870℃固溶、 40 %～ 5 0 %冷变形及 480℃× 1 5h时效处理后 ,合金可获得良好的综合性能。     

硬质合金磨削温度的实验研究

采用半人工和人工热电偶法，对硬质合金YG6和YT30平面磨削的磨削温度进行了实验研究。并对磨削参数与磨削温度的关系，进行了理论分析及实验验证。结果表明：磨削深度和工作台速度增加，磨削温度升高，但工作台速度的改变，对磨削温度的影响较小．     

耐候钢连铸工艺的改进

分析耐候钢连铸出现的问题,认为凝固时应力过大和磷铜元素偏析造成晶界脆化是出现铸坯纵裂的主要原因;结晶器中喂稀土丝恶化保护渣性能,影响结晶器与坯壳间的润滑与传热,并使热流不均匀是连铸漏钢的主因。采用钙处理代喂稀土丝工艺,以及减缓连铸一、二次冷却强度,改进保护渣后,连铸缺陷获得极大改善。     

Influencing factors on elastic-plastic deformation of multi-layered surfaces under sliding contact

Stress distribution in the gradient multi-layered surface under a sliding contact was investigated using finite element method(FEM). The main structure parameters of layered surface discussed are total layer thickness,layer number and elastic modulus ratio of layer to the substrate. A model of multi-layered surface contact with rough slider was studied. The effect of the surface structure parameters on the elastic-plastic deformation was analyzed.