碳纤维连续抽油杆作业车自动调平系统设计

为保证碳纤维连续抽油杆作业车作业时工作平台处于水平状态,防止侧翻,开展了作业车自动调平系统的设计。在给出自动调平系统构成的基础上,着重论述了系统的自动调平控制方案、自动调平控制原理以及自动调平控制软件的设计,给出作业车自动调平控制系统流程图。     

微波干燥在气相超稳Y型分子筛制备中的应用研究

研究了微波干燥在气相超稳Y型分子筛制备中的应用。结果表明，分子筛经微波干燥后，其理化性质有所改善，结晶度提高，经气相超稳化反应后其产品结构及物化性质与传统电加热干燥后的气相超稳产品基本一致，说明微波干燥可替代传统干燥方式。与传统电加热干燥方式相比，微波干燥能缩短干燥时间，有效降低能耗。     

一种用于三电平逆变器的SVPWM调制方法研究

本文从二极管箝位型三电平逆变器的基本结构出发，分析其输出状态，推导出六角形空间电压矢量图。然后从一种改进的，可以减小开关损耗，避免高的dv／dt三电平空间矢量PWM调制策略出发，建立了基于Matlab的详细仿真方案，验证了方案的可行性。文章给出了扇区判断的算法流程图，脉冲生成模块的内部结构图，其中的扇区判断的算法和脉冲生成方法对于用DSP实现三电平SVPWM具有重要的参考价值。     

一种基于H.235协议的关守消息认证机制

首先对基于用户秘密散列签名的关守消息认证机制做了简单介绍,然后针对该机制的不足之处提出了一种基于H.235协议的改进方法,具有安全性高,速度快,管理方便等优点.     

高含沙水深井泵站的综合治理

对攀钢动力厂深井泵站自投产以来出现的主要问题及其解决方案，方法进行了分析和论述。     

回热损失对磁斯特林制冷循环制冷率的影响

从铁磁质的磁化强度一般表示式出发，探讨热阻和回热损失对磁斯特林制冷循环性能的影响，导出最大制冷率及其它性能参数。得到了结果适用于以顺磁质为工质的磁斯特林制冷循环。并指出在理想回热条件下的结论也适用于磁卡诺制冷循环。     

2-乙基己酸的制备

研究了 2乙基己酸的制备 ,该反应是 2乙基己醇与氢氧化钠在催化剂存在下进行氧化、脱氢 ,生成产物2乙基己酸。通过实验找到了一种新型、高效、廉价的催化剂 ,以及最佳反应条件。通过对 2乙基己酸的分析测试 ,产品完全符合质量标准。     

菱镁矿固硫特性的理论分析

对菱镁矿在固体燃料燃烧过程中的固硫特性进行了理论研究，所得结论对进一步将菱镁矿作为固体燃料燃烧过程中的固硫剂具有非常重要的意义。     

Reduction of sodium-accelerated oxidation of silicon nitride ceramics by aluminium implantation

Norton NBD 200 silicon nitride ceramics were implanted with sodium to a dose of 7.0×10¹⁵cm^-2 at 72 keV (1 at% peak sodium content at 100 nm). The sodium-implanted samples were further implanted with aluminium to 7.3×10¹⁵cm^-2 at 87 keV (1 at% peak aluminium content at 100 nm). The implanted and unimplanted samples were oxidized in 1 atm dry oxygen at 1100 and 1300°C for 2–6 h. Profilometry and scanning electron microscopy measurements indicated that sodium implantation led to up to a two-fold increase in the oxidation rate of silicon nitride. The sodium effect was effectively neutralized when aluminium was co-implanted. The opposite effects of sodium and aluminium on the oxidation resistance of silicon nitride can be attributed to their different roles in modifying the structure and properties of the oxide formed. This revised version was published online in November 2006 with corrections to the Cover Date.     

Economic cost modeling of environmental-stress-screening andburn-in

The electronics industry is highly competitive. The introduction of new advanced integrated circuits continues. The manufacturer must develop a product with adequate life cycle, high quality and low failure rate in the specified time period. Environmental stress screening (ESS) is widely used in the electronics industry to assist in eliminating early or patent failures. The bathtub curve is a common model for the failure rate of a population. The classic bathtub curve has three parts: infant mortality; useful life; and wearout. However, some electronic products have latent defects which are not detected by conventional inspection or functional testing, and occur during the product useful life. Most electronic systems have finite useful life. As a result, technology obsolescence is of concern and should be considered, This paper uses a new interpretation and development of the bathtub curve that integrates: (1) latent failures; and (2) the concept of obsolescence, by constructing an integrated cost model used to determine both optimal burn-in and ESS times in the same environment