Neural networks and blood cell identification

The objective of this project is to propose a method of identifying cells found in human blood and to classify them based upon their morphological features using neural networks. The project focuses on three major blood cell types, namely, erythrocytes, leukocytes and platelets. The data are collected using peripheral blood smears from clinical patients. The image acquisition requires 100x magnification on all the blood smears, the preprocessing involves the use of median and edge enhance filters; the feature extraction is done by performing the wavelet transform on the images. Finally classification of the blood cell types is done using ALOPEX and Back Propagation trained neural networks. The efficacy of both networks is then compared by comparing their outputs and number of iterations required to reach the final result.     

Small-signal modeling and control of the quasi-square-wave boostconverter

Sampled-data techniques are used to examine the dynamic characteristics and closed-loop performance of the quasi-square-wave boost converter. Direct duty-ratio control and current-mode control are considered. With direct duty-ratio control, the system poles remain well damped under all load conditions, and there is no zero in the control-to-output transfer function. Good closed-loop performance is therefore achieved. Under current-mode control, the requirement for a stabilizing ramp is seen to depend on load conditions, and the achievable voltage control-loop bandwidth is smaller than that using direct duty-ratio control; however, there is a significant reduction in the magnitude of the DC source to output-voltage frequency response     

Synthesis and characterization of molybdenum disulphide formed from ammonium tetrathiomolybdate

An investigation has been carried out into the possibility of in situ formation of MoS2 within porous anodic films on aluminium, to improve subsequent tribological behaviour, by re-anodizing in thiomolybdate electrolyte. Acidification of thiomolybdate was employed to simulate the conditions for formation of the sulphide at the anodic film/electrolyte interface, followed by appropriate vacuum heat treatments to study possible temperature effects on the sulphide due to either friction or Joule heating during anodizing. The products of both acidification and heat treatment, characterized by X-ray powder diffraction and scanning electron microscopy, were compared with those formed by direct thermal decomposition of ammonium tetrathiomolybdate crystals. The precipitate formed by acidification was mainly amorphous molybdenum trisulphide (MoS3), which on heat treatment at 450 and 850°C yielded 3R-MoS2. 3R-MoS2 also formed by the thermal decomposition of thiomolybdate crystals. Thermogravimetric and differential thermal analyses showed that the decomposition of MoS3 to MoS2 occurred in the range 220–370°C and revealed the sequence of reaction steps. The findings suggest that mainly amorphous MoS3 is formed as a consequence of changes in the pH of the film/electrolyte interface during re-anodizing but the product is relatively easily transformed to crystalline MoS2 on moderate heating which may occur during wear processes.     

A novel method for elimination of line-current harmonics insingle-stage PFC switching regulators

This paper studies a particular single-stage power-factor-correction (PFC) switching regulator employing a discontinuous-conduction-mode (DCM) boost-input cell and a continuous-current-mode (CCM) forward output cell. Although this single-stage PFC regulator can provide a reasonably high power factor when its PFC stage is operating in discontinuous mode, substantial reduction in line-current harmonics is possible by applying a suitable frequency-modulation scheme. This paper derives a frequency-modulation scheme and proposes a practical implementation using a simple translinear analog circuit. A quantitative analysis on the total harmonic distortion (THD) of the line current when the circuit is subject to a limited range of frequency variations is presented along with some considerations for practical design. Experimental data obtained from a prototype confirms the effectiveness of the proposed frequency-modulation scheme. The proposed analog translinear circuit allows custom integrated circuit implementation, making it a viable low-cost solution to the elimination of line-current harmonics in switching regulators     

Regional chemotherapy of liver tumors

In the absence of adequate autogenous vein for tibial artery bypass in limb salvage surgery, the use of prosthetic grafts with a distal anastomotic vein cuff or patch has shown promising results. Here, we describe how the Florester Internal Vessel Occluder (Meadox UK, Bedfordshire, UK) can facilitate the construction of a distal anastomotic vein cuff.     

Evaluation of multicast routing algorithms for real-timecommunication on high-speed networks

Multicast (MC) routing algorithms capable of satisfying the quality of service (QoS) requirements of real-time applications will be essential for future high-speed networks. We compare the performance of all of the important MC routing algorithms when applied to networks with asymmetric link loads. Each algorithm is judged based on the quality of the MC trees it generates and its efficiency in managing the network resources. Simulation results over random networks show that unconstrained algorithms are not capable of fulfilling the QoS requirements of real-time applications in wide-area networks. Simulations also reveal that one of the unconstrained algorithms, reverse path multicasting (RPM), is quite inefficient when applied to asymmetric networks. We study how combining routing with resource reservation and admission control improves the RPM's efficiency in managing the network resources. The performance of one semiconstrained heuristic, MSC, three constrained Steiner tree (CST) heuristics, Kompella, Pasquale, and Polyzos (1992), constrained adaptive ordering (CAO), and bounded shortest multicast algorithm (BSMA), and one constrained shortest path tree (CSPT) heuristic, the constrained Dijkstra heuristic (CDKS) are also studied. Simulations show that the semiconstrained and constrained heuristics are capable of successfully constructing MC trees which satisfy the QoS requirements of real-time traffic. However, the cost performance of the heuristics varies. The BSMA's MC trees are lower in cost than all other constrained heuristics. Finally, we compare the execution times of all algorithms, unconstrained, semiconstrained, and constrained     

Preparation of SiC particles coated with alumina hydrate: Effect of reaction condition on particle coalescence

Alumina-hydrate-coated SiC particles were prepared via a homogeneous precipitation method using urea, and the conditions for uniform coating and less coalescence of the particles were investigated. Coalescence of coated particles could be said to occur by collision and agglomeration followed by deposition of alumina hydrate on the agglomerated particles. Coalescence of coated particles was suppressed by use of low reaction temperature, low concentration of aluminium sulfate, high concentration of urea, intensive stirring, and a flow reactor.