Multifunctional alkylphenol additive

Translated from Khimiya i Tekhnologiya Topliv i Masel, No. 2, pp. 14–15, February, 1989.     

PCR-based procedures in detection and DNA-fingerprinting of Salmonella from samples of animal origin

The usefulness of selected PCR-protocols for the detection of Salmonella in 117 samples of animal origin (17 raw minced meat, 27 raw chicken meat, 8 raw sausages, and 25 egg samples, as well as 18 poultry faecal, and caecal swabs samples) and DNA-fingerprinting typing is shown. To establish an accurate PCR-procedure for Salmonella detection the following parameters were evaluated: two pre-PCR concentration procedures, centrifugation and immunomagnetic separation (IMS) using Dynabeads anti- Salmonella; the specificity and sensitivity of 10 sets of primers; and different conditions of the amplification reaction. In light of the results obtained from the use of PCR-based procedures alone or in combination with conventional methods, the following findings can be underlined: First, IMS is more efficient than centrifugation in the recovery of Salmonella. Second, the selected IMS/PCR-detection protocol is less time-consuming (45 h) than the IMS/culture procedure (90 h), and a good concordance between them was found when the Kappa coefficient was calculated (0·87). Third, PCR-ribotyping technique showed a very low discrimination power, being able to differentiate only three profiles. Fourth, RAPD technique using specific primers supports previous works in which it was proposed as a simple and useful tool for discriminating isolates between and within serotypes. Fifth, The efficiency, rapidity, and flexibility of the PCR-protocols applied were high, and they can be performed using two PCR-programs and the same basic equipment.     

Tube-shaping unit — A way of improving the quality of shaped tubes

Lenin Dnepropetrovsk Pipe Plant. Translated from Metallurg, No. 8, p. 39, August, 1989.     

Half-bridge inverter using 4H-SiC gate turn-off thyristors

This paper reports on the first demonstration of a half-bridge power inverter constructed from silicon carbide gate turn-off thyristors (GTOs) operated in the conventional GTO mode. This circuit was characterized with input bus voltages of up to 600 VDC and 2 A (peak current density of 540 A/cm²) with resistive loads using a pulse-width modulated switching frequency of 2 kHz. We discuss the implications of the thyristor's electrical characteristics and the circuit topology on the overall operation of the half-bridge circuit. This work has determined the conservative critical rate of rise value of the off-state voltage to be 200 V/μs in these devices     

Theoretical analysis of control properties for the brushless doubly fed reluctance machine

The brushless doubly fed induction machine (BDFIM) has been extensively researched for approximately 30 years, but a related machine [the brushless doubly fed reluctance machine (BDFRM)], has not. This was mainly due to the fact that reluctance rotor designs were not capable of generating saliency ratios large enough to make the BDFRM competitive with other machines. However, recent developments in reluctance rotors, spurred on by research into synchronous reluctance machines, has resulted in high saliency ratio rotors that are economic to build. This, together with the promise of higher efficiency and simpler control compared to the BDFIM, means that further investigation of the BDFRM is warranted. A relatively limited amount of work to date has been published on the BDFRM. This paper attempts to fill this void by presenting a theoretical analysis of some of the important control properties of the ideal BDFRM.     

Crisis phenomena upon evaporation in grid capillary and porous coatings and arterial structures of heat pipes

The article presents the results of experimental investigations of critical (limit) heat fluxes upon evaporation on porous coatings, and it substantiates the physical model of the process.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 49, No. 4, pp. 607–614, October, 1985.