PTA压力离心机转子的改造

介绍了PTA压力离心机的主要性能参数、工作原理、分离效果的影响因素。为了增大沉渣在过渡区及脱水区滞留的时问，同时为达到在过渡区及脱水区对沉渣加入纯净水进行再冲洗的目的，对螺旋送料转子、挡液环、进料管进行了改造。改造后，沉渣在脱水区的停留时间由0．44a增至0．72s，2．5～3t／h的冲洗水对脱水区的沉渣进行冲洗效果较好。产品中的杂质质量分数较改造前减少15％，产品优等品率提高到99％。     

一台循环流化床锅炉U型二次分离的改进对过热器爆管的影响

文章通过对一台循环流化床锅炉U型二次分离装置的改进，减少了过热器爆管的介绍，给出了采用多次离心分离技术，改善和提高烟尘分离效率，从而改善过热器外部工作条件，达到减少爆管发生的措施，相应提出了一些有关的建议。     

均匀设计法分析制备过程对钴钼硫化物催化剂机械强度的影响

建立了CoMoP/Al2O3加氢精制催化剂机械强度及其可靠性在制备过程中的数学模型,采用均匀设计考察了浸渍、干燥、煅烧、硫化4个制备过程中,浸渍时间、干燥温度、干燥时间、煅烧温度、煅烧时间、硫化温度和硫化升温速率7个实验因子对催化剂强度均值、Weibull模量的影响,同时考察了这些因素对颗粒密度的影响。方差分析表明所有模型都是充足的。实验结果表明,硫化过程是影响催化剂强度均值的主要过程。在实验范围内提高硫化温度、降低硫化时的升温速率有利于提高催化剂的强度。影响催化剂Weibull模量的因素主要为各个制备过程的交互效应。要提高催化剂强度的可靠性就必须全面考虑催化剂制备的各个过程,特别是各个制备过程的交互效应。     

Quasi-Chun-Ching Shih''''s Fractional Fourier Transform with Periodicity of 2,3 and M

Based on Chun-Ching Shih's idea, the basic transform was substituted and the quasi-ChunChing Shih's fractional Fourier transform with periodicity of 2, 3 and M was deduced. The two former transforms and the Chun-Ching Shih's fractional Fourier transform were only the particular cases of quasiChun-Ching Shih's fractional Fourier transform with periodicity of M.     

Analysis and Simulation of S-shaped Waveguide in Silicon-on-insulator

The simulation and analysis of S-shaped waveguide bend are presented.Bend radius larger than 30 mm assures less than 0.5 dB radiation loss for a 4-μm-wide silicon-on-insulator waveguide bend with 2-μm etch depth.Intersection angle greater than 20° provides negligible crosstalk (<-30 dB) and very low insertion loss.Any reduction in bend radius and intersection angle is at the cost of the degradation of characteristics of bent waveguide and intersecting waveguide, respectively.     

电接点压力表补水泵定压系统的应用

阐述了电接点压力表补水泵定压系统的一些应用问题 ,给出了电接点压力表定压点的上、下限计算公式 ,并提出了该系统补给水泵、补给水箱及安全阀的设计选型方法     

防腐涂料及涂装技术(Ⅷ)

防腐涂料及涂装技术讲座系列介绍防腐蚀涂料的品种和各类应用及最新产品研究进展。本讲主要介绍涂装前的表面预处理方法及表面处理质量的评定等     

Viterbi译码器的硬件实现

介绍了一种Vkerbi译码器的硬件实现方法。设计的基于硬判决的Viterbi译码器具有约束长度长（9)、译码深度深（64)的特点。为了兼顾硬件资源与电路性能两个方面，在设计中使用了4个ACS单元，并根据Xilinx Virtex系列FPGA的结构特点．利用FPGA内部的BlockRAM保存汉明距离和幸存路径，提高了译码速度。     

粘土矿物对低渗透储层性质的影响——以鄂尔多斯盆地三叠系低渗透储层为例

粘土矿物是低渗砂岩储层的主要胶结物，对储层物性及开发过程中储层物性变化趋势有着重要的影响和控制作用。另外，粘土矿物也蕴含着大量沉积环境介质的物理化学信息，认识其自然规律，可以有效地指导预测有利储层，认识和改造油层。以鄂尔多斯盆地砂岩储层中的粘土矿物为研究对象，探讨分析粘土矿物对低渗储层性质的影响，该研究对含油气盆地低渗储层有效开发具有一定的参考价值。     

Microstructure and Mechanical Properties of Heat-treated GeSb_2Te_4 Thin Films

The effect of annealing on microstructure,adhesive and frictional properties of GeSb 2 Te 4 films were experimentally studied.The GeSb 2 Te 4 films were prepared by radio frequency(RF)magnetron sputtering,and annealed at 200℃and 340℃under vacuum circumstance,respectively.The adhesion and friction experiments were mainly conducted with a lateral force microscope(LFM)for the GeSb 2 Te 4 thin films before and after annealing.Their morphology and phase structure were analyzed by using atomic force microscopy(AFM)and X-ray Diffraction(XRD)techniques,and the nanoindention was employed to evaluate their hardness values.Moreover,an electric force microscope(EFM)was used to measure the surface potential. It is found that the deposited GeSb 2 Te 4 thin film undergoes an amorphous-to-fcc and fcc-to-hex structure transition;the adhesion has a weaker dependence on the surface roughness,but a certain correlation with the surface potential of GeSb 2 Te 4 thin films.And the friction behavior of GeSb 2 Te 4 thin films follows their adhesion behavior under a lower applied load.However,such a relation is replaced by the mechanical behavior when the load is relatively higher.Moreover,the GeSb 2 Te 4 thin film annealed at 340℃presents a lubricative property.