Photoreactivation of Escherichia coli following medium-pressure ultraviolet disinfection and its control using chloramination.

Ultraviolet (UV) disinfection is becoming increasingly popular as an alternative disinfection technology to chlorination in recent years. In this study, we investigated the photoreactivation of Escherichia coli following medium-pressure (MP) UV disinfection of synthetic water by a bench-scale collimated beam apparatus. The UV doses ranged from 1.6 -19.7 mWs/cm2 and photoreactivation was investigated for 6 hours under fluorescent light. In addition, chloramination was applied after UV disinfection to investigate its ability to control photoreactivation. It was found that photoreactivation occurred for all UV doses tested and the increase in bacteria numbers ranged from 0.04 to 1.35 log10. However, the degree of photoreactivation decreased with increased UV doses. Chloramination experiments revealed that the addition of 0.5 mg/l of monochloramine resulted in suppression of photoreactivation for 1 hour only. An increased monochloramine dose of 1 mg/l was found to prevent photoreactivation for the entire duration of the experiment. The results of this study have shown that photoreactivation occurs even after MP UV disinfection, although it is of a lesser extent at higher UV doses. This study has also established that secondary chloramination can effectively suppress and eliminate photoreactivation with a chloramine dose of 1 mg/l.     

立方相GaN的持续光电导

研究了金属有机物化学气相外延 (MOVPE)方法生长的非故意掺杂的立方相 Ga N的持续光电导效应 .在六方相 Ga N中普遍认为持续光电导效应与黄光发射有关 ,而实验则显示在立方 Ga N中 ,持续光电导效应与其中的六方相 Ga N夹杂有关系 ,而与黄光发射没有关系 .文中提出 ,立方相 Ga N与其中的六方相 Ga N夹杂之间的势垒引起的空间载流子分离是导致持续光电导现象的物理原因 .通过建立势垒限制复合模型 ,解释了立方相 Ga N的持续光电导现象的物理过程 ,并对光电导衰减过程的动力学作了分析 .对实验数据拟合的结果证明以上的模型和推导是与实验相符的 .     

Solution of large deformation contact problems with friction between Blatz-Ko hyperelastic bodies

The present paper is devoted to the analysis of the contact problems with Coulomb friction and large deformation between two hyperelastic bodies. One approach to separate the material nonlinearity and contact nonlinearity is presented. The total Lagrangian formulation is adopted to describe the geometrically nonlinear behavior. Nondifferentiable contact potentials are regularized by means of the augmented Lagrangian method. Numerical examples are carried out in two cases: rigid-deformable contact and deformable-deformable contact with large slips. The numerical results prove that the proposed approach is robust and efficient concerning numerical stability.     

Novel algorithms for shared segment protection

The major challenges in designing survivable schemes are how to allocate a minimal amount of spare resources (e.g., bandwidth) using fast (e.g., polynomial-time) algorithms, and, in case a failure occurs, to be able to recover quickly from it. All existing approaches invariably make tradeoffs. We propose novel shared segment protection algorithms which make little or no compromise . We develop an elegant integer linear programming (ILP) model to determine an optimal set of segments to protect a given active path. Although the ILP approach is useful for a medium-size network, it is too time consuming for large networks. Accordingly, we also design a fast heuristic algorithm based on dynamic programming to obtain a near-optimal set of segments. Although the heuristic algorithm has a polynomial time complexity, it can achieve a bandwidth efficiency as high as some best-performing shared path protection schemes and, at the same time, much faster recovery than these shared path protection schemes. The proposed scheme is also applicable to a wide range of networking technologies, including Internet Protocol and wavelength-division multiplexing networks under the generalized multiprotocol label switched framework.     

Achieving fast and bandwidth-efficient shared-path protection

Dynamic provisioning of restorable bandwidth guaranteed paths is a challenge in the design of broad-band transport networks, especially next-generation optical networks. A common approach is called (failure-independent) path protection, whereby for every mission-critical active path to be established, a link (or node) disjoint backup path (BP) is also established. To optimize network resource utilization, shared path protection should be adopted, which often allows a new BP to share the bandwidth allocated to some existing BPs. However, it usually leads the backup paths to use too many links, with zero cost in term of additional backup bandwidth, along its route. It will violate the restoration time guarantee. In this paper, we propose novel integer linear programming (ILP) formulations by introducing two parameters (/spl epsi/ and /spl mu/) in both the sharing with complete information (SCI) scheme and the distributed partial information management (DPIM) scheme. Our results show that the proposed ILP formulations can not only improve the network resource utilization effectively, but also keep the BPs as short as possible.     

A generalized equation for the prediction of melting temperatures of homopolymers and copolymers

A generalized equation was derived to calculate the melting temperatures of homopolymers and copolymers. The Gibbs‐Thomson equation for homopolymers and a modified application to copolymers were derived using the proposed equation. The melting temperature T_m⁰ in the Flory equation corresponds to the melting temperature T_m^C,∞ of copolymer crystals with stems of infinite length. Also, T_m^C,n*, the melting temperature for copolymer crystals with stems containing the maximum possible number of structural units, n*, should be used instead of T_m⁰ as the basis of supercooling in crystallization. The proposed equation shows good agreement with experimental data for α‐alkene‐ethylene homogeneous copolymers.     

中温换热器检查及修复方案

经分析认为中温换热器缺陷出现的主要原因是H2 S腐蚀。采取更换短管以及补焊上段下管板的措施进行修复 ,取得了满意的效果     

Rheology in Processing of in Situ Composites of Polypropylene and Low Melting Poing Metals

The low melting point metallic tin powder or alloy of tin and lead was blended with polypropy-lene. A kind of in situ composite has been prepared. The variations of torque were studied when the composites were mixed in Haake torque rheogeniometer. By way of capillary extrusion, effects upon rheology of the in situ com-posites of the low melting point metals (LMPM) and coupling agent for their different variety and content, were investigated. From flow curves, the results indicate that in situ composites mixed with the LMPM are a kind of pseudoplastic fluid. If the LMPM were melted, the higher the content of the LMPM , the lower apparent viscosity of composites. Meanwhile, when the coupling agent is added into composites, the viscosity of composite will go up first and drop then. This shows that the LMPM have a promoter flow action on the polypropylene.     

Bi3+对纳米MnO2水热合成的影响研究

在中性和酸性条件下，以MnO2作为锰源，通过水热合成了纳米MnO2，通过XRD和TEM对产物进行的观察表明，在酸性条件下，向溶液中添加一定量的Bi^3 ，产物的晶型由α型向γ型转化，产物形貌由针状、丝状向颗粒状转变。     

烷基烷氧基硅烷的合成方法及其在涂料中的应用

介绍了烷基烷氧基硅烷的合成方法(包括烷基的引入方法和烷氧基的形成方法)、近几年来在涂料中的应用及其结构与性能的关系。