湖北省承接东部地区加工贸易产业转移的思考

我国加工贸易由东部向中西部地区转移的趋势已经形成.面对广大中西部省份的激烈竞争,湖北省要立足自身优势,大力承接东部地区的加工贸易产业转移,积极投入基础设施建设,加大招商引资力度,创造良好的投资环境,引导当地劳务人员就业观念,完善产业配套体系,推动加工贸易产业集群.     

大学生政治信仰状况的调查与思考

当今社会正处于加速转型期,大学生的政治信仰状况值得关注和深思.通过调查分析发现,大学生的政治信仰呈现多元化趋势,表现出个性化的特点.加强大学生政治信仰教育极为重要,必须强化思想政治教育课程主阵地作用,营造政治信仰教育的良好社会氛围,拓宽大学生政治信仰教育新渠道,发挥大学生在政治信仰教育中的主观能动性.     

Research on the Control Strategy of Variable Nozzle Turbocharger for Natural Gas Engine

A variable nozzle turbocharger (VNT) was applied to a 2.2-liter L4 natural gas engine,and a VNT control system was designed to operate it.Based on VNT matching test results,a VNT control strategy was studied,in which VNT adjustment is carried out through pre-calibrated VNT handling rod position,combined with a closed-loop target boost pressure feedback using proportional-integral-derivative(PID) algorithm.Experimental results showed that the VNT control system presented in this thesis can lead to optimized ...     

Development of AMT Fault Diagnosis Technique Based on KWP2000

In order to make automatic mechanical transmission (AMT) capable of performing fault self-diagnoses and adaptive to standard communication interface,through technical analysis and intensive study concerning on-board diagnostic protocols now widely applied in Europe and America,KWP2000 on CAN is accepted as a technological path.An AMT fault communication system using hardware-in-the-loop simulation by dSPACE is developed,and communications compatible with ISO 15031-6 is realized on this module.Moreover,a han...     

共振散射光谱法研究槲皮素与DNA相互作用

在BR缓冲液中,槲皮素存在微弱的共振散射现象,分别在288 nm、466 nm、562 nm处出现共振散射峰,随着DNA的加入,散射信号逐渐增强,且以上3处的峰值明显增加,并且562 nm处的增加值与DNA在3.024×10-7 mol/L～9.072×10-5 mol/L范围内呈现出良好的线性关系.在20℃时,通过Scatchard方程计算出槲皮素与DNA结合常数K=9.91×106 mol-1.L.     

波导-带状线耦合传输的分析

文章分析了波导-带状线通过小孔耦合的传输特性,通过保角变换求出带状线中的场分布,利用小孔衍射理论得到波导-带状线间的耦合度的表达式,并且理论计算值与测量值吻合较好.通过数值分析,结果表明:耦合小孔半径和厚度对耦合度的影响比较大,传输线的工作频带比较宽.     

少齿差减速器偏心轴及偏心套加工工艺研究

针对具有较高精度的偏心轴及偏心套加工问题,采用了组合式工艺偏心轴——套,并利用电火花线切割保证偏心精度。     

上海东方体育中心综合体育馆屋盖结构风振分析

在屋盖同步风洞试验测量的基础上,采用CQC法对上海东方体育中心综合体育馆大跨屋盖进行了较为准确的空间风振分析。分析了多个复杂空间振型对有代表性节点的动位移根方差的影响,得到本体育馆的最大参振振型为30阶;考虑了两种荷载组合工况,比较了工况1、工况2和自重作用下屋盖结构的节点位移和基底反力,工况1作用下的节点位移和基底反力最大,工况2作用下的相应结果最小;最后给出了5个不利风向下的位移风振系数,可供参考。     

Optimum location of surface wells for remote pressure relief coalbed methane drainage in mining areas

Based on engineering tests in the Huainan coal mining area,we studied alternative well location to improve the performance of surface wells for remote pressure relief of coalbed methane in mining areas.The key factors,affecting location and well gas production were analyzed by simulation tests for similar material.The exploitation results indicate that wells located in various positions on panels could achieve relatively better gas production in regions with thin Cenozoic layers,low mining heights and slow rate of longwall advancement,but their periods of gas production lasted less than 230 days,as opposed to wells in regions with thick Cenozoic layers,greater mining heights and fast rates of Iongwall advancement.Wells near panel margins achieved relatively better gas production and lasted longer than centerline wells.The rules of development of mining fractures in strata over panels control gas production of surface wells.Mining fractures located in areas determined by lines of compaction and the effect of mining are well developed and can be maintained for long periods of time.Placing the well at the end of panels and on the updip return airway side of panels,determined by lines of compaction and the effect of mining,would result in surface wells for remote pressure relief CBM obtaining their longest gas production periods and highest cumulative gas production.     

Longitudinal crack on slab surface at straightening stage during continuous casting using finite element method

Deformation behavior of slab at the straightening stage during continuous casting was simulated by the explicit dynamic finite element method, and the stress distribution along the width direction of the slab and its change regularity at slab center during continuous casting were obtained. The influence of distribution and change of stress on the propagation of longitudinal cracks on slab surface was discussed. The results show that the tensional stress appears on slab surface at the inner arc side and the compressive stress appears on slab surface at the outer arc side at stages 6-8 in straightening zone during continuous casting. Longitudinal cracks generally appear on slab top surface and do not appear on slab bottom surface, which are also observed in industry.