MRF-based texture segmentation using wavelet decomposed images

In recent textured image segmentation, Bayesian approaches capitalizing on computational efficiency of multiresolution representations have received much attention. Most of the previous researches have been based on multiresolution stochastic models which use the Gaussian pyramid image decomposition. In this paper, motivated by nonredundant directional selectivity and highly discriminative nature of the wavelet representation, we present an unsupervised textured image segmentation algorithm based on a multiscale stochastic modeling over the wavelet decomposition of image. The model, using doubly stochastic Markov random fields, captures intrascale statistical dependencies over the wavelet decomposed image and intrascale and interscale dependencies over the corresponding multiresolution region image.     

A study on the chromaticity shifts of blue phosphor for color plasma displays

The dependency of the chromaticity shifts on the concentration of Eu²⁺ doped in BaMgAl₁₀O₁₇ (BAM) was investigated under heat‐treatment and vacuum ultraviolet (VUV) irradiation. The Eu²⁺ ions in BAM show an asymmetrical broad emission band with a maximum at ～452 nm under excitation of VUV light at room temperature, showing that multiple crystalline cationic sites exist in the host. It was found that the chromaticity shifts greatly decrease with increasing heat‐treatment temperature. Regardless of the Eu²⁺ concentration, the chromaticity shifts caused by heat‐treatment are greater than that caused by VUV irradiation. Compared with conventional BAM, a solid solution of BAM with barium aluminate as a powder and film was also studied, and very few chromacity shifts were observed. It is suggested that the distribution of Eu²⁺ ions in different sites in a BAM lattice results in different chromaticity coordinates. By increasing the Eu²⁺ concentration in BAM, or under heat‐treatment and VUV irradiation, the emission band shifts towards longer wavelengths.     

Preparation and morphology of as-prepared and highly stretch-aligned polyacetylene

The macroscopic morphology of as-prepared polyacetylene depends on the concentration of the catalyst system. At high catalyst concentration, polymerization occurs on the free surface of the catalyst solution to form a polyacetylene film which retards further polymerization because of the limited diffusion of acetylene monomer through the film. At lower concentrations, however, successive diffusion and polymerization is possible yielding a gelatinous mass. A continuous mass does not form at an extremely low concentration; the product is flock or powder. Despite these differences in macroscopic morphology, electron micrographs show that the fibrillar structure is a common feature of all forms of polyacetylene. However, the average fibril diameter of 200 Å may depend on the polymerization conditions. Orientation of the fibrils by combined mechanical and thermal treatment is possible to produce highly stretch-aligned films which show anisotropic properties.     

Rate of emulsion polymerization of styrene

In emulsion polymerization, the Smith and Ewart theory gives about two or three times the number of polymer particles obtained by experiment. In this paper, a reaction model is proposed which, from the standpoint of reactor design, can give an adequate explanation of the whole course of an emulsion polymerization of monomer highly insoluble in water. Among other things, the generating process of polymer particles is examined in detail. It is demonstrated experimentally that a new parameter proposed here, which represents the degree of difficulty of monomer initiation in micelles, is indispensable in explaining that process. Also confirmed is that monomer initiation takes place more easily in polymer particles than in micelles. According to the new model, the progress of polymerization, i.e., monomer conversion, the number of the polymer particles, and properties of polymer thus produced can be estimated with satisfactory accuracy. Furthermore, approximate equations are derived for easier estimation.     

Pulsed laser irradiation impact on two marine diatoms Skeletonema costatum and Chaetoceros gracilis

The ability of pulsed laser irradiations to cause damage on the biofouling organisms is recently being investigated. If this technique is employed in industries such as power generation wherein a large quantity of water is being used for the cooling purpose, many organisms other than the targeted would get affected. In this study, we have investigated the damage caused by the pulsed laser irradiations from an Nd:YAG laser (fluence 0.1J/cm(2)) for varying durations such as 2, 5, 10, 30, 60 and 300 s on two marine diatom species namely Skeletonema costatum and Chaetoceros gracilis. Upon exposure to low power laser irradiations, these diatom species showed mortalities between 52.6+/-9.3% to 97.7+/-3.1% in the case of S. costatum and 57.8+/-2.5% to 98.9+/-0.6% in the case of C. gracilis for 2 and 300 s of irradiations, respectively. The mortality increased with the increase in the duration of laser irradiation. The estimation of the chlorophyll a concentration in the irradiated samples showed a considerable reduction varying between 9.8% and 57% in C. gracilis and 3% and 70.3% in S. costatum for 2 and 300 s of irradiations, respectively. The laser-survived cells grew as the non-irradiated (control) samples. C. gracilis frustules were broken by the laser whilst, the cell materials were drained out of the frustules in the case of S. costatum. The study therefore showed that the low power pulsed laser irradiations could cause significant damage on the two species of planktonic diatoms.     

Spectral interference Mirau microscope with an acousto-optic tunable filter for three-dimensional surface profilometry

A nonmechanical scanning Mirau-type spectral interference microscope has been developed for the measurement of three-dimensional surface profiles of discontinuous objects. An acousto-optic tunable filter (AOTF) is used as a high-resolution spectral filter, which scans the optical frequency of the broadband light emitted from a superluminescent diode. To generate spectral fringes that make full use of the limited coherence length of the filtered light we unbalanced the Mirau interferometric system by positioning the reference mirror nearly halfway between the top and the bottom of the step height. When the frequency of the broadband light source is scanned by an AOTF, the interference fringes move in opposite directions on the top and the bottom of the object. To uniquely determine the sign of the fringe movement over the large area of the object, we developed a three-dimensional Fourier-transform technique, and from the detected sign of the fringe movement and phase information, we determined the three-dimensional step height. Experimental results of the measurement of 100-microm step height are presented. The main advantages of the proposed system are that it provides nonmechanical scanning and a large measurement range without ambiguity in the sign of the phase.     

The study of metal ion release and cytotoxicity in Co–Cr–Mo and Ti–Al–V alloy in total knee prosthesis – scanning electron microscopic observation

We surgically retrieved two cobalt(Co)–chromium(Cr)–molybdenum(Mo) and five titanium(Ti)–aluminum(Al)–vanadium(V) alloy knee prostheses from patients because of mechanical failure and pain. We examined the distribution of the small particles which were released from the Co–Cr–Mo and Ti–Al–V alloys using a backscattered scanning electron microscopy (SEM). In addition we analyzed the metals in the artificial knee joints and the tissues adjacent to them using energy dispersive X-ray spectroscopy (EDS). We demonstrated that a myriad of fine particles, produced by the abrasion of both Co–Cr–Mo and Ti–Al–V alloys, accumulated in the synovial cells. As Co–Cr–Mo alloys disintegrate easily in the cells, Co dissolves from the peripheral areas of them, although Cr remains within the cells. In contrast Ti–Al–V alloys are very stable in the synovial cells. From these findings we conclude that the Co–Cr–Mo alloys are hazardous to the body as the alloys release Co which enters the body. In contrast the Ti–Al–V alloys are very stable and are patently safer. Artificial joints, however, are still in considerable need of improvement.