Influence of index table accuracy on roundness calibration in the multi-step method using monte carlo simulation

The precise and accurate roundness measurement is required year by year. The multi-step method is commonly used in the high-accuracy measurement for the roundness. The multi-step method is the self-calibration of the roundness capable of performing highly-advanced precise measurement. It depends on the reason that is able to separate measurement wave from the spindle rotation component and the form component of hemispherical master. But the mathematical models of the roundness measurement using that method are very complicated, describing numerous parameters and processes. So, recently, the Monte Carlo technique has attracted increasing attention as a very useful method for uncertainty estimation. This paper describes influences of the indexing angle accuracy and the noises generated by the roundness measuring machine, on the roundness measurements, both of which were analyzed by the Monte Carlo simulation. Furthermore, an example of hemispherical master is compared with the actual measurement data between when a reference guide plate is used utilizing the magnetic rotary encoder.     

Examination of the Mode II fracture behaviour of wood with a short crack in an asymmetric four-point bending test

Asymmetric four-point bending tests of agathis specimens with a short crack along the neutral axis in a tangential–longitudinal system were conducted onto analyse the failure behaviour of wood with a short crack. The nominal shear strength and Mode II critical stress intensity factors of the specimens with various crack lengths were measured, and the influence of crack length on these properties was examined. The nominal shear strength of the cracked specimens was significantly lower than the strength of a crack-free specimen, even when the crack was extremely short. This finding suggests that the fracture mechanics theory is effective for analysing the failure behaviour of wood with a very short crack in this loading condition. However, the Mode II critical stress intensity factor still depends on the crack length. When the crack length was corrected with considering the formation of fracture process zone ahead of the crack tip, the critical intensity factor could be predicted effectively as well as the nominal shear strength.     

Casting of organic glass by radiation-induced polymerization of glass-forming monomers at low temperature. II. Optical strain of remaining stress type

Previously it was found that casting could be carried out efficiently without strain formation by radiation-induced polymerization of glass-forming monomers. Two types of strain were observed in casting: thermal stream type, which was studied previously, and remained stress type. In this report, the effect of various factors on the formation of remaining stress-type strain in radiation-induced casting polymerization was studied. It was found that the molecular weight of prepolymer did not affect strain formation, while prepolymer concentration and viscosity of the system had a serious influence on strain formation. It could be deduced that this type of strain formed as a result of remaining inner stress due to poor relaxation of the shrinking stress. It was realized that less volume shrinkage of glass-forming monomers accompanying casting polymerization reduced the strain formation of this type in radiation-induced casting polymerization at low temperatures.     

Iodine-initiated,solid-state copolymerization of tetraoxane with 1,3-dioxolane in the presence of methylal. II. Properties of copolymer obtained by beaker-scale copolymerization

In order to elucidate the copolymerization mechanism, the properties of the copolymer obtained by the iodine-initiated copolymerization of the tetraoxane–1,3-dioxolane–methylal system have been studied using gas chromatography, microscopy, scanning electron microscopy, differential scanning calorimetry, and gel permeation chromatography. From the behavior of the thermal stability and gas chromatography of the reaction mixture, it was found that reactivity of 1,3-dioxolane with active center is larger than that of tetraoxane, i.e., more than 90% 1,3-dioxolane is consumed at an early stage of the polymerization. The results obtained by microscopy, DSC, and GPC of the copolymer suggested that the copolymerization proceeds from the surface to the center of the tetraoxane crystal as if it were a core model. It was also suggested that the heterogeniety in copolymer properties can be explained not only by heterogeneous dispersion of 1,3-dioxolane in tetraoxane crystal, but also by the difference of reactivity of 1,3-dioxolane with the active center.     

Permeative separation of metal ions through the polymer membrane containing gluconate group

Summary The adsorption and permeation of metal ion mixtures were examined for the membrane of poly(3-O-vinylbenzyl gluconate-co-acrylonitrile). The membrane is found to be effective for permeative separation of metal ions. For the Cu/Cd combination, especially, Cu ion was selectively adsorbed and permeated in a neutral aqueous solution. The high selectivity and the high permeation rate are discussed in connection with the chelate formation and the hydrophilicity of ion channel.     

Thermal Stability of Hexaaluminate Film Coated on SiC Substrate for High-Temperature Catalytic Application

A coating of barium hexaaluminate (Ba_0.75Al_11.0O_17.25) on an α-SiC substrate and the thermal stability of the formed film were investigated for a high-temperature catalytic application. The film prepared by sol coating consisted of BaAl₂Si₂O₈ and α-Al₂O₃ phases and always contained many cracks or exfoliations after heating at 1200C. A hexaaluminate porous film was successfully formed by slurry coating without void formation at the interface between the film and the substrate and exfoliation due to the formation of the intermediate layer after heating at 1200°C. The microstructure of the film remained unchanged, even after heating at 1300°C.     

Hydrogel of biodegradable cellulose derivatives. I. Radiation‐induced crosslinking of CMC

Radiation crosslinking of carboxymethylcellulose (CMC) with a degree of substitution (DS) from 0.7 to 2.2 was the subject of the current investigation. CMC was irradiated in solid‐state and aqueous solutions at various irradiation doses. The DS and the concentration of the aqueous solution had a remarkable affect on the crosslinking of CMC. Irradiation of CMC, even with a high DS, 2.2 in solid state, and a low DS, 0.7 in 10% aqueous solution, resulted in degradation. However, it was found that irradiation of CMC with a relatively high DS, 1.32, led to crosslinking in a 5% aqueous solution, and 20% CMC gave the highest gel fraction. CMC with a DS of 2.2 induced higher crosslinking than that with a DS of 1.32 at lower doses with the same concentration. Hence, it was apparent that a high DS and a high concentration in an aqueous solution were favorable for high crosslinking of CMC. It is assumed that high radiation crosslinking of CMC was induced by the increased mobility of its molecules in water and by the formation of CMC radicals from the abstraction of H atoms from macromolecules in the intermediate products of water radiolysis. A preliminary biodegradation study confirmed that crosslinked CMC hydrogel can be digested by a cellulase enzyme. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 278–283, 2000     

Effect of metallic wire inserted in nozzle in high-speed melt spinning of poly(ethylene terephthalate)

High-speed melt spinning of poly(ethylene terephthalate) was performed using a spinning nozzle with an inserted metallic wire of various lengths (0, 8, 30, and 45 mm). The molecular orientation of as-spun fibers increased with the increase in the wire length at all the take-up velocities examined. Along with the enhanced molecular orientation, the longer wire length led to the starting of orientation-induced crystallization at lower take-up velocities. The structure of crystallized fibers obtained at low speeds can be characterized by high crystallinity and relatively low molecular orientation. From the on-line measurement of the diameter and temperature profiles of the spin line with the 30-mm metallic wire, it was revealed that the spin-line had a maximum diameter of about 6 mm at the wire end. The spin-line temperature at this position was about 190°C. The solidification of the spin-line occurred at positions much closer to the spinneret in comparison with ordinary high-speed spinning. These results show that high-speed spinning with a wire inserted in the nozzle corresponds to a spinning process operated at extremely low extrusion temperature using a nozzle with an extremely large diameter. From the starting of orientation-induced crystallization at lower levels of birefringence in comparison with ordinary high-speed spinning, the alteration of the inherent fiber structure that cannot be represented by birefringence was also suggested. © 1998 John Wiley & Sons, Inc. J. Appl. Polym. Sci. 70: 665–674, 1998     

A new class of transparent polymeric materials. III. Miscible blends of poly(N-methylmaleimide-alt-isobutene) with poly(acrylonitrile-co-styrene) and the properties of the blends

The blend miscibility of poly(N-methylmaleimide-alt-isobutene) [poly-(MeMI-IB)] with poly(acrylonitrile-co-styrene) (SAN) was investigated by means of measurement of the glass transition temperature of the blends. Poly(MeMI-IB) was found to be miscible with SAN of a specific range of acrylonitrile (AN) contents in the copolymer to produce transparent moldings. The refractive index changed from 1.58 to 1.53 and the dispersion decreased with increasing the amount of poly(MeMI-IB) in the blends. The stress optical coefficient of poly(MeMI-IB) was found to be reduced by the blending of SAN. The glass transition temperature, flexural modulus, and surface hardness of the blends increased with an increase in the amount of poly(MeMI-IB) in the blend. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 63: 925–929, 1997     

Mechanisms of tubulin modification by phosphatidylcholine hydroperoxides

The interaction of lipid peroxides with cellular proteins has been postulated to contribute to cellular aging. A potential target for such effects is tubulin, the building block of microtubules. We examined the concentration-dependent effects of phosphatidylcholine hydroperoxides on the ability of tubulin to polymerize into microtubules. The results demonstrated that even very low concentrations of peroxides were sufficient to interfere with the tubulin and, therefore, the microtubule function. Decreased tubulin activity (as measured by tubulin GTPase activity) showed correlation with the modification of methionine and cysteine in tubulin and a change in the tubulin conformational state as indicated by fluorescence and ultraviolet spectroscopic measurements. As no effect on electric conductivity was observed, indicating that modulation of ionic binding was not involved, the interaction mechanism may be a hydrophobic one.