Influence of asymmetric electrode geometry on an impedance spectrum of a plasma-sprayed thermal barrier coating system

Influence of asymmetric electrode geometry on an impedance spectrum of a plasma-sprayed thermal barrier coating (TBC) system was investigated. The impedance spectrum of the TBC system included impedance of the yttria stabilized zirconia (YSZ) grains, YSZ grain boundaries (negligible), the thermally grown oxide (TGO) and the electrode reaction. In the TBC system with a continuous TGO layer, the impedance of the YSZ grain was measured without influence of asymmetric electrode geometry above 100 kHz. In a frequency range below 100 kHz, asymmetric electrode geometry induced the spread of an electrical conduction region outside an electrode attached on the top coating surface. The impedance of the TGO and the electrode reaction was significantly affected by the asymmetric electrode geometry. The precise interpretation of an impedance spectrum of TBC systems measured under the condition of asymmetric electrode geometry requires further studies on the spread of an electrical conduction region due to decrease in frequency, increase in asymmetry of electrode geometry.     

Multi-walled carbon nanotube-reinforced copper nanocomposite coating fabricated by low-pressure cold spray process

Multi-walled carbon nanotube (MWCNT)-reinforced copper (Cu) nanocomposite coatings were successfully deposited on aluminum (Al) substrate by a cold spraying process at a low pressure. The microstructure and the Raman spectrum of the low-pressure-cold-sprayed MWCNT–Cu nanocomposite coating showed that the MWCNTs maintained their tube structure in the Cu matrix, even though structural damage to the MWCNTs increased slightly. MWCNT–Cu nanocomposite-coated Al exhibits higher thermal diffusivity than pure-Cu-coated Al with a comparable hardness. The higher thermal diffusivity of the MWCNT–Cu coating could be explained by the dispersion of MWCNTs within the clean and closed CNT/Cu interfaces, which were achieved with the aid of compressive stress during the cold spraying.     

Lipid analog with 2-nitrophenol trigger designed for liposome fusion at physiological pH

A novel lipid analog with two long alkyl (C₁₆) chains, an aspartate skeleton, a connecting alkyl (C₈) chain, and 2-nitrophenol trigger group is synthesized by an efficient synthetic route, which can induce liposome fusion at physiological pH.     

Molecular simulation for adsorption of chlorinated hydrocarbon in zeolites

Equilibrium and isosteric heat of adsorption for the system of chloroform and USY-type zeolite were studied. The USY-type zeolite (PQ Co., SiO₂/Al₂O₃=70) was used both as a pure crystalline powder and as granulated particles with binder. Chloroform was reagent grade. The adsorption equilibria were measured using a gravimetric method and were expressed as isotherms. A chromatographic method (i.e. pulse response of chloroform through the USY column with helium carrier) was used to get the initial slope of the isotherms. In the simulation, the GCMC method was used to calculate amounts adsorbed for various conditions. FF parameters were confidently applied. And modified structure model was effective for simulation. This paper was presented at The 5th International Symposium on Separation Technology-Korea and Japan held at Seoul between August 19 and 21, 1999.     

Water Vapor Adsorption and Desorption on Materials Hydrothermally Solidified from Clay Minerals

Water vapor isotherms were examined and ¹H-magic-angle spinning nuclear magnetic resonance (¹H-MAS NMR) analysis was conducted to determine the amount of water vapor adsorbed and desorbed on hydrothermally solidified materials derived from clay minerals. The amount of water vapor adsorbed and desorbed decreased with increasing mesopore volume of the materials, which disagreed with the estimation obtained using the Kelvin equation. Water vapor was physisorbed on alumina-like sites in the materials. An increase in the binding energy between water vapor and the materials led to an improvement in the water vapor adsorption–desorption properties of materials.     

Differences in Sterol Composition between Male and Female Gonads of Dominant Limpet Species

The present study demonstrated here for the first time that there are statistically significant differences in sterol composition between male and female gonads of the dominant limpets Cellana grata and Cellana toreuma, which are intertidal gastropods. Among 11 different sterols identified in this study, unusually high levels (11.2–19.8% of total sterols) of the Δ⁸-sterols 5α-cholest-8-en-3β-ol (zymostenol) and 5α-cholesta-8,24-dien-3β-ol (zymosterol), which have never been reported in aquatic invertebrate gonads, were present in only the male gonads.     

Ethanol Conversion on MCM-41 and FSM-16, and on Ni-Doped MCM-41 and FSM-16 Prepared without Hydrothermal Conditions

MCM-41 and FSM-16 were both prepared using no hydrothermal conditions, and nickel was doped into these catalysts (Ni-MCM-41 and Ni-FSM-16) using a template ion exchange method. FSM-16 and Ni-FSM-16 had greater catalytic activity for the conversion of ethanol than MCM-41 and Ni-MCM-41, indicating that FSM-16 has potential as a catalyst for the conversion of ethanol to propylene.     

Wear resistance of a Cr3C2-NiCr detonation spray coating

Coatings can be applied to surfaces to improve the surface characteristics over those of the bulk properties and are widely used in tribological applications either to reduce wear and/or to modify friction during contact. One of the foremost coating methods for combating wear is thermal spraying. To prolong the life of steel slab continuous casting rolls, Cr₃C₂-NiCr detonation spray coating was processed on the roll surface in a steelmaking plant in China. This article studies the mechanical properties and wear resistance of this coating. The abrasive and dry frictional wear testing were performed using a pin-on-disk tester. Experimental results show that the wear resistance of the coated samples, i.e., coating reduces the risk of seizure compared to uncoated samples, is much better than those of the uncoated steel at room and elevated temperatures with any load and sliding velocity. The coating wear mechanisms under different test conditions are discussed.     

Phase separation and dewetting in polystyrene/poly(vinyl methyl ether) blend thin films in a wide thickness range

Phase separation and dewetting processes of blend thin films of polystyrene (PS) and poly(vinyl methyl ether) (PVME) in two phase region have been studied in a wide film thickness range from 65 μm to 42 nm (∼2.5R_g, R_g being radius of gyration of a polymer) using optical microscope (OM), atomic force microscope (AFM) and small-angle light scattering (LS). It was found that both phase separation and dewetting processes depend on the film thickness and were classified into four thickness regions. In the first region above ∼15 μm the spinodal decomposition (SD) type phase separation occurs in a similar manner to bulk and no dewetting is observed. This region can be regarded as bulk. In the second region between ∼15 and ∼1 μm, the SD type phase separation proceeds in the early stage while the characteristic wavelength of the SD decreases with the film thickness. In the late stage dewetting is induced by the phase separation. In the third region between ∼1 μm and ∼200 nm the dewetting is observed even in the early stage. The dewetting morphology is very irregular and no definite characteristic wavelength is observed. It is expected that the irregular morphology is induced by mixing up the characteristic wavelengths of the phase separation and the dewetting. In the fourth region below ∼200 nm the dewetting occurs after a long incubation time with a characteristic wavelength, which decreases with the film thickness. It is considered that the layered structure is formed in the thin film during the incubation period and triggers the dewetting through the capillary fluctuation mechanism or the composition fluctuation one.