Comparative study on the preparation and properties of radiation‐grafted polymer electrolyte membranes based on fluoropolymer films

In this study the fluoropolymers, poly(ethylene‐co‐tetrafluoroethylene) (ETFE) and poly(vinylidene fluoride) (PVDF) films, together with the radiation‐induced crosslinked polytetrafluoroethylene (cPTFE) film were compared on the basis of their preparation and properties of radiation‐grafted polymer electrolyte membranes. The polymer electrolyte membranes were prepared by radiation grafting of styrene into the base films and subsequent sulfonation. The proton conductivity and chemical stability of the three types of membranes with a similar ion exchange capacity (IEC) near 1.0 mmol/g were investigated and are discussed in detail. Although the ETFE‐based polymer electrolyte membrane was relatively more stable, its proton conductivity was lower than those of the PVDF‐ and cPTFE‐based membranes. On the other hand, the cPTFE‐based membrane showed a significantly higher proton conductivity, but its chemical stability was shorter than that of the ETFE‐based membrane. It is considered that the difference in the preparation and properties of the polymer electrolyte membranes was due to the difference in the degree of crystallinity as well as in the chemical structure of the fluoropolymer base films. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1966–1972, 2007     

Fabrication and Microstructure Characterization of Ti3SiC2 Synthesized from Ti/Si/2TiC Powders Using the Pulse Discharge Sintering (PDS) Technique

Ti/Si/2TiC powders were prepared using a mixture method (M) and a mechanical alloying (MA) method to fabricate Ti₃SiC₂ at 1200°–1400°C using a pulse discharge sintering (PDS) technique. The results showed that the Ti₃SiC₂ samples with <5 wt% TiC could be rapidly synthesized from the M powders; however, the TiC content was always >18 wt% in the MA samples. Further sintering of the M powder showed that the purity of Ti₃SiC₂ could be improved to >97 wt% at 1250°–1300°C, which is ∼200°–300°C lower than that of sintered Ti/Si/C and Ti/SiC/C powders using the hot isostatic pressing (HIPing) technique. The microstructure of Ti₃SiC₂ also could be controlled using three types of powders, i.e., fine, coarse, or duplex-grained, within the sintering temperature range. In comparison with Ti/Si/C and Ti/SiC/C mixture powders, it has been suggested that high-purity Ti₃SiC₂ could be rapidly synthesized by sintering the Ti/Si/TiC powder mixture at relatively lower temperature using the PDS technique.     

Effect of metallic ions in photo-induced graft copolymerization onto cellulose

In photo-induced graft copolymerization of methyl methacrylate onto cellulose, the effect of metallic ions as sensitizer was investigated. Some metallic ions were effective in their adsorbed states and accelerated the formation of grafts in the order Fe²⁺ > Ag⁺ > Fe³⁺. However, Cu²⁺ acted negatively, and little effect was observed for Co²⁺, Ni²⁺, Mn²⁺, Zn²⁺, and Cr³⁺. In the systems in which aqueous metallic salt solutions were added, the formation of grafts was generally depressed, but Fe³⁺ was an exception. The effect of metallic ions on the scission reaction of cellulose main chains did not necessarily agree with the effect on the formation of grafts. This is attributed to the varied interaction between cellulose and the different active species produced by irradiation, depending on the type of metallic ions used.     

Graft copolymerization to cellulose. Effect of sodium thiosulfate on hydrogen peroxide initiator system

The effect of sodium thiosulfate on the graft copolymerization of methyl methacrylate to cellulose in the hydrogen peroxide initiator system was investigated. The addition of sodium thiosulfate in general was effective for decreasing the per cent grafting and the average molecular weight of grafts and increasing the formation of homopolymer, and the effects became pronounced with increasing hydrogen peroxide concentration. Moreover, the addition of sodium thiosulfate slightly suppressed the formation of grafts at a hydrogen peroxide concentration of 3 mmole/l., but greatly promoted it at 20 mmole/l. Traces of metallic ions present in cellulose could not be eliminated sufficiently by treatment with 3N hydrochloric acid. Such ions were found to interact with hydrogen peroxide and thus participate directly in the initiation and termination of the polymerization reaction. EDTA, the chelating agent, was highly effective for suppressing such participation of metallic ions. In the hydrogen peroxide initiator system applied to the EDTA-treated samples, sodium thiosulfate caused an effective initiation of graft formation.     

Simultaneous Perturbation Stochastic Approximation with Norm‐Limited Update Vector

This paper addresses the convergence of simultaneous perturbation stochastic approximation (SPSA) with a norm‐limited update vector. We first illustrate an unstable solution of the standard SPSA algorithm which motivates the consideration of a modified version, where the norm of the update vector is limited to a certain value. Next, a result on the almost‐sure convergence is presented by reducing the modified algorithm into the standard SPSA algorithm and restricting the probability distribution for the perturbation to a Bernoulli distribution. Finally, we apply the modified algorithm to a system identification problem to demonstrate its performance.     

Impedancemetric gas sensor based on Pt and WO3 co-loaded TiO2 and ZrO2 as total NOx sensing materials

Pt-loaded metal oxides [WO₃/ZrO₂, MO_x/TiO₂ (MO_x = WO₃, MoO₃, V₂O₅), WO₃ and TiO₂] equipped with interdigital Au electrodes have been tested as a NO_x (NO and NO₂) gas sensor at 500 °C. The impedance value at 4 Hz was used as a sensing signal. Among the samples tested, Pt-WO₃/TiO₂ showed the highest sensor response magnitude to NO. The sensor was found to respond consistently and rapidly to change in concentration of NO and NO₂ in the oxygen rich and moist gas mixture at 500 °C. The 90% response and 90% recovery times were as short as less than 5–10 s. The impedance at 4 Hz of the present device was found to vary almost linearly with the logarithm of NO_x (NO or NO₂) concentration from 10 to 570 ppm. Pt-WO₃/TiO₂ showed responses to NO and NO₂ of the same algebraic sign and nearly the same magnitude, while Pt/WO₃ and WO₃/TiO₂ showed higher response to NO than NO₂. The impedance at 4 Hz in the presence of NO for Pt-WO₃/TiO₂ was almost equal at any O₂ concentration examined (1–99%), while in the case of Pt/WO₃ and WO₃/TiO₂ the impedance increased with the oxygen concentration. The features of Pt-WO₃/TiO₂ are favorable as a NO_x sensor that can monitor and control the NO_x concentration in automotive exhaust. The effect of WO₃ loading of Pt-WO₃/ZrO₂-based sensor is studied to discuss the role of surface W-OH sites on the NO_x sensing.     

A bio-inspired predictive sensory-motor coordination scheme for robot reaching and preshaping

This paper presents a sensory-motor coordination scheme for a robot hand-arm-head system that provides the robot with the capability to reach an object while pre-shaping the fingers to the required grasp configuration and while predicting the tactile image that will be perceived after grasping. A model for sensory-motor coordination derived from studies in humans inspired the development of this scheme. A peculiar feature of this model is the prediction of the tactile image. The implementation of the proposed scheme is based on a neuro-fuzzy module that, after a learning phase, starting from visual data, calculates the position and orientation of the hand for reaching, selects the best-suited hand configuration, and predicts the tactile feedback. The implementation of the scheme on a humanoid robot allowed experimental validation of its effectiveness in robotics and provided perspectives on applications of sensory predictions in robot motor control.     

Engineering Transition Metal Layers for Long Lasting Anionic Redox in Layered Sodium Manganese Oxide

Oxygen-redox-based-layered cathode materials are of great importance in realizing high-energy-density sodium-ion batteries (SIBs) that can satisfy the demands of next-generation energy storage technologies. However, Mn-based-layered materials (P2-type Na-poor Na_y[A_xMn_1−x]O₂, where A = alkali ions) still suffer from poor reversibility during oxygen-redox reactions and low conductivity. In this work, the dual Li and Co replacement is investigated in P2-type-layered Na_xMnO₂. Experimentally and theoretically, it is demonstrated that the efficacy of the dual Li and Co replacement in Na_0.6[Li_0.15Co_0.15Mn_0.7]O₂ is that it improves the structural and cycling stability despite the reversible Li migration from the transition metal layer during de-/sodiation. Operando X-ray diffraction and ex situ neutron diffraction analysis prove that the material maintains a P2-type structure during the entire range of Na⁺ extraction and insertion with a small volume change of ≈4.3%. In Na_0.6[Li_0.15Co_0.15Mn_0.7]O₂, the reversible electrochemical activity of Co³⁺/Co⁴⁺, Mn³⁺/Mn⁴⁺, and O^2-/(O₂)^n- redox is identified as a reliable mechanism for the remarkable stable electrochemical performance. From a broader perspective, this study highlights a possible design roadmap for developing cathode materials with optimized cationic and anionic activities and excellent structural stabilities for SIBs.     

Observers and output feedback stabilising controllers for nonlinear strict-feedback systems with sampled observation

The design of observers and output feedback stabilising controllers for continuous-time strict-feedback systems with sampled observation is considered. First two types of observers are designed. One is a discrete-time semiglobal and practical reduced-order observer for the exact model and the other is a continuous-time semiglobal and practical full-order observer for continuous-time strict feedback systems with sampled observation. Then by combining the designed continuous-time observers and continuous-time state feedback laws that are continuous, zero at the origin, and uniformly globally asymptotically stabilise continuous-time systems, output feedback semiglobally practically uniformly asymptotically stabilising controllers are constructed. Numerical examples are given to illustrate the proposed design of observers and output feedback controllers.     

Indirect augmented reality

Developing augmented reality (AR) applications for mobile devices and outdoor environments has historically required a number of technical trade-offs related to tracking. One approach is to rely on computer vision which provides very accurate tracking, but can be brittle, and limits the generality of the application. Another approach is to rely on sensor-based tracking which enables widespread use, but at the cost of generally poor tracking performance. In this paper we present and evaluate a new approach, which we call Indirect AR, that enables perfect alignment of virtual content in a much greater number of application scenarios.To achieve this improved performance we replace the live camera view used in video see through AR with a previously captured panoramic image. By doing this we improve the perceived quality of the tracking while still maintaining a similar overall experience. There are some limitations of this technique, however, related to the use of panoramas. We evaluate these boundaries conditions on both a performance and experiential basis through two user studies. The result of these studies indicates that users preferred Indirect AR over traditional AR in most conditions, and when conditions do degrade to the point the experience changes, Indirect AR can still be a very useful tool in many outdoor application scenarios.