High modulus of isotactic polypropylene attained by coextrusion with atactic polystyrene

Orientation-induced crystallization of crystallizable polymer melts can occur, under certain conditions, during flow through converging channels. Attempts have been made to achieve this phenomenon in a two-phase system, i.e., during simultaneous extrusion of a continuous concentric core of polypropylene within a polystyrene matrix through a conical duct. On one occasion, using Carlona P SY6100 (MFI = 11.0) with Hostyren N2000-V-01 (MFI = 25.0), a highly oriented polypropylene thread with a modulus of 14.6 GPa and a melting point of 178°C was extruded at a die temperature of approximately 170°C and a pressure lower than 40 MPa. It is, in principle, possible to form highly oriented, fiber-like structures as reinforcing elements in a polymer matrix.     

Application of Code Approach for Emergency Evacuation in a Rail Station

This paper presents an emergency evacuation analysis during a mid-platform train fire in an underground rail station. A time-based evacuation scenario is developed taking into account the stairway inaccessibility due to smoke blockage. The calculation approach in NFPA 130 is then applied to a parametric study of this time-based scenario and its reliability is examined using a micro-simulation model. Both methods give consistent predictions of the exiting times. The results demonstrate that with the division of the station into two zones, the exiting time could not meet the code requirements, whereas it does meet the required exiting time without the division. Such division is due to smoke blockage and creates an uneven ratio of the occupant load to the available exiting capacity. This shows that appropriate consideration of the fire and smoke effects is important for station egress evaluation. Other issues such as the fire growth rate and the pre-evacuation time are also discussed.     

Microprocessor testability

As the level of microprocessor complexity increases to several hundred thousand transistors for a single-chip machine, it is becoming very difficult to test commercially available designs to the level of fault coverage desired by some customers. In order to achieve near 100-percent coverage of single stuck-at faults, future microprocessors must be designed with special testing features (designed for testability). The authors describe the testing problem for microprocessors, including the various methods of generating test sets and their application by the user. A survey of the testability features of some of today's commercially available microprocessors is presented. Suggestions for testability features for future-generation microprocessors are also discussed     

Detection of failure sites by focused ion beam and nano-probing in the interconnect of three-dimensional stacked circuit structures

Focused ion beam (FIB) and nano-probing were applied for failure analysis of three-dimensional stacked circuits with copper through-silicon-vias between the stacked chips. The failure analysis was done after high temperature storage and thermal cycling tests. Passive voltage contrast in FIB allowed to pinpoint the open sites. FIB cross-sections showed the presence of opens at the bottom of the copper vias. The failure cause was suspected to be an interlayer particle, which was confirmed by optical profilometry. Nano-probing was used on another sample to pinpoint the failure location through the measurement of the local resistance within the daisy chains. The failure was traced out to be related with surface contamination.     

IPv6 delay and loss performance evolution

Although packet delay and loss are two important parameters of the Internet performance, to the best of our knowledge, the evolution of large‐scale IPv6 delay and loss performance has previously not been studied. In this paper, we analyze more than 600 end‐to‐end IPv6 paths between about 26 testboxes of RIPE Network Coordination Centre over two years, and compare the delay and loss performance over time with their IPv4 counterparts. We present and discuss the measurement methodologies and show that IPv6 paths have a higher delay and loss than their IPv4 counterparts. The main reason for the worse performance stems from IPv6‐in‐IPv4 tunnels rather than from native IPv6 paths and such tunnels are still widely used today. Copyright © 2007 John Wiley & Sons, Ltd.     

Influence of Production Process Parameters on Fish Oil Quality in a Pilot Plant

ABSTRACT: A pilot plant used for upgrading herring byproducts into fish oil was analyzed on its operational efficiency and product quality. The temperature of the heat exchanger and the speeds of the pump and the 3-phase decanter were varied according to a 2³ fractional factorial design. The initial amount of oxidation products present in the crude oil, its storage stability, and the yields from the different obtained products were determined. Multivariate data analysis of the advanced screening stage showed that T had neither influence on the quality nor on the yield in contrast to D and MP (P < 0.05). Process optimization results showed that the quality of the oil was influenced by an interaction effect between the speed of the MP and the D. Oils processed with the highest MP speed were the most stable during storage.     

Photonic Demodulator With Sensitivity Control

A current assisted photonic demodulator for use as a pixel in a 3-D time-of-flight imager shows nearly 100% static demodulator contrast and is operable beyond 30 MHz. An integrated tunable sensitivity control is also presented for increasing the distance measurement range and avoiding unwanted saturation during integration periods. This is achieved by application of a voltage on a dedicated drain tap showing a quenching of sensor sensitivity to below 1%     

Thermoelectric Converters of Human Warmth for Self-Powered Wireless Sensor Nodes

Solar cells are the most commonly used devices in customer products to achieve power autonomy. This paper discusses a complementary approach to provide power autonomy to devices on a human body, i.e., thermoelectric conversion of human heat. In indoor applications, thermoelectric converters on the skin can provide more power per square centimeter than solar cells, particularly in adverse illumination conditions. Moreover, they work day and night. The first sensor nodes powered by human heat have been demonstrated and tested on people in 2004-2005. They used the state-of-the-art 100-muW watch-size thermoelectric wrist generators fabricated at IMEC and based on custom-design small-size BiTe thermopiles. The sensor node is completed with a power conditioning module, a microcontroller, and a wireless transceiver mounted on a watchstrap     

Systems that Should Have Failed: Critical Infrastructure Protection in an Institutionally Fragmented Environment

Recent years have witnessed major governmental initiatives regarding critical infrastructure protection (CIP). During that same time, critical infrastructures (CIs) have undergone massive institutional restructuring under the headings of privatization, deregulation and liberalization. Little research has gone into understanding the interactions between these two developments. In this article, we outline the consequences of institutional restructuring for the changing ways in which CIs ensure the reliability and security of their networks and services. Neither Normal Accident Theory nor High‐Reliability Theory can account for reliability under these conditions. We then investigate the implications of these findings for CIP.     

A single-grain approach applied to the modeling of recrystallization kinetics for cold-rolled single-phase metals

A comprehensive model for the recrystallization kinetics is proposed which incorporates both microstructure and the textural components in the deformed state. The model is based on the single-grain approach proposed previously. The influence of the as-deformed grain orientation, which affects the stored energy via subgrain size and sub-boundary misorientation, is taken into account. The effects of the deformed grain geometry, the nucleation-site density, and the initial grain size prior to deformation on the recrystallization kinetics are assessed. The model is applied to the recrystallization kinetics of a cold-rolled AA1050 alloy.