Some theoretical aspects of the electrophoretic sedimentation of particles

This paper concerns the theoretical interpretation of the results of a previous experimental study of the sedimentation of oxidized fine aluminum and iron particles in waste kerosene under the influence of an electric field. Following the Kynch analysis of the mode of gravity sedimentation, a modified particle volume flux is introduced to compensate for the effect of the electric field strength. It is shown that if the local electric field strength at the settling interface is used as the true driving force for electrophoretic sedimentation, the settling curves can be predicted with reasonable accuracy, provided that electrical heating effects and consequent temperature changes in the system are taken into account.Some theoretical aspects of the effects of dielectric polarization on settling are also discussed and illustrated qualitatively by the experimental data. Finally, some of the factors which might be expected to affect the energy efficiency of a particle separator operating by electrophoretic sedimentation are considered.     

Preparation of modified poly(vinyl chloride) containing N,N-di(β-hydroxyethyl)dithiocarbamate and its reaction with metal ions

Reaction of N,N-di(β-hydroxyethyl)dithiocarbamate ion with poly(vinyl chloride) (PVC) was undertaken, and the reaction with metal ions of the polymer obtained was investigated. The effect of γ-irradiation on the reaction with metal ion was also studied. The modified PVC (PHDC) obtained from the reaction with N,N-di(β-hydroxyethyl)dithiocarbamate ion is pale yellow even after reaction at 100°C for 5 hr in dimethylformamide (DMF); it is soluble in dipolar solvents and its chlorine content is decreased considerably. This polymer reacted well with acetate salts of copper(II), nickel(II), zinc(II), and silver(I) heterogeneously in aqueous solution because of the introduction of hydrophilic groups (two hydroxy groups). The reactivity of the metal ions toward the polymer was of the order Ag(I) ? Cu(II) > Ni(II) > Zn(II). From the result of the reaction of γ-irradiated polymer with cupric ion, the polymer was judged to have fairly good antiradiation property.     

Efficient usage of highly dispersed Pt on carbon nanotubes for electrode catalysts of polymer electrolyte fuel cells

A Pt-deposited carbon nanotube (CNT) shows higher performance than a commercial Pt-deposited carbon black (CB) with reducing 60% Pt load per electrode area in polymer electrolyte fuel cells (PEFCs) below 500 mA/cm². K₂PtCl₄ and H₂PtCl₆·6(H₂O) are used for the Pt deposition onto multi-walled CNTs (MWCNTs), which are produced by the catalytic decomposition of hydrocarbons. The electric power densities produced using the Pt/CNT electrodes are greater than that of the Pt/CB by a factor of two to four on the basis of the Pt load per power. CNTs are thus found to be a good support of Pt particles for PEFC electrodes. TEM images show 2–4-nm Pt nanoparticles dispersed on the CNT surfaces. These high performances are considered to be due to the efficient formation of the triple-phase boundaries of gas–electrode–electrolyte. The mechanisms of Pt deposition are discussed for these Pt-deposited CNTs.     

Study on modified phenolic resin. II. Modification with p-hydroxyphenylmaleimide/styrene copolymer

The improvement of heat resistance and mechanical properties of phenolic resin was examined with the blend of novolac and copolymers prepared from p-hydroxyphenylmaleimide (HPMI) and styrene. Copolymers of HPMI and styrene with various molecular weights were synthesized. Glass transition (T_g) and thermal decomposition temperatures of the copolymers were measured by differential scanning calorimetry (DSC) and thermogravimetry (TG), respectively. The miscibility of the copolymers with novolac was examined by DSC. It was found that the copolymers had a good heat resistance and a good miscibility with novolac. Molding compounds were prepared by hot roll-kneading of mixtures that involved novolac, copolymer, hexamethylenetetramine (hexamine), and glass fiber. It was found that the test pieces prepared by transfer molding from the molding compounds showed a good heat resistance and better mechanical properties than phenolic resin modified with HPMI homopolymer.     

Photocatalysts using hexa- and octa-titanates with different tunnel space for water decomposition

Photocatalytic activities for water decomposition were examined for photocatalysts using hexa- and octa-titanates and TiO2(B) with different tunnel space in the structure. Using RuO2 as promoter, M2Ti6O13 (M = Li, Na, K, Rb) showed the stoichiometric production of Hz and O₂ except for Li, whereas H₂Ti₈O₁₇ and TiO₂(B) had very low activity producing only hydrogen as a product. The effects of promoters on Na₂Ti₆O₁₃ showed that the activity increased in the order of RuO₂ > RuO₂ + IrO₂ > IrO₂ > RuO₂ + Pt > MnO₂. These effects along with other related ones are discussed: it emerges that the presence of the tunnels is important for the achievement of high photocatalytic activity.     

Soluble and colorless polyimides with polyalicyclic structures [1]

Two tetracarboxylic dianhydrides with polyalicyclic structure, bicyclo[2.2.2]octane-2-endo, 3-endo, 5-exo, 6-exo-2,3:5,6-dianhydride (5a) and the all-exo isomer (5b), were synthesized in six steps using phthalic acid as a starting material. The dianhydrides were polymerized at 85–105°C in well-purified DMAc with aromatic diamines which were purified by two recrystallizations and then sublimation. The polyimides formed flexible and tough films, and were soluble in aprotic polar solvents such as DMAc. The 5%-weight loss temperatures were over 450°C. The polyimides possessed glass-transition temperatures in the range from 211 to 385°C. The polyimides films had a tensile modulus range of 1.5–2.6 GPa, a tensile strength range of 52–96 MPa, and an elongation range at break of 3–11%. The polyimide films showed cutoffs at wavelengths shorter than 320 nm and were entirely colorless. The colorlessness of the polyimide films was maintained up to 200°C when heated in air and to 400°C in a N₂ atmosphere.     

Triterpene alcohols and sterols of Spanish olive oil

Nine Spanish olive oils, including three each of virgin (pressed oil), refined virgin, and B-residue (solvent-extracted pomace oil) oils from different commercial sources, have been analyzed for their unsaponifiable matter (USM). Four sterolic fractions separated from the oils have been analyzed by preparative thin-layer chromatography (TLC); these fractions are triterpene alcohols, 4-methylsterols, sterols and triterpene dialcohols. The compositions of the four sterolic fractions were determined as their acetates by gas-liquid chromatography (GLC) on an OV-17 glass capillary column. Identification of each component was carried out by argentation TLC, GLC and combined gas chromatography-mass spectrometry (GC-MS); 44 components were identified, of which four: 24-methylene-31-nor-9(11)-lanostenol, 24-methyl-31-nor-E-23-dehydrocycloartanol, 24-ethyl-E-23-dehydrolophenol and 5,E-23-stigmastadienol, were considered to be new sterols from natural sources. Several characteristics, including the content of triteterpene dialcohols in the USM and that of C-24(28) unsaturated sterols in each of the four sterolic fractions, which can be used to distinguish between virgin and B-residue olive oils, were observed.     

XPS Characterization of reduced LaCoO3 perovskite

Three samples of LaCoO₃ were prepared by two different methods and calcined at 800 or 1000 °C. They had BET areas of 1, 12, and 16 m²/g and all of them showed pure perovskite X-ray diffraction patterns with identical unit cell dimensions. In a series of experiments the oxide, having larger surface area, was stepwise reduced in hydrogen at temperatures between 60 and 500 °C. The XPS spectra, taken at room temperature after evacuation at 400 °C at each reduction level, showed that the surface concentration of Co° was very low up to 300 °C but increased sharply between 300 and 350 °C (9–75%). This concentration further increased to 100% after 10 min reduction at 450 °C, but upon heating in hydrogen for an additional 10 min at 500 °C it decreased again to 75%. In another series of experiments the mixed oxide was reoxidized after each reduction. A fresh sample was reduced to 350 and 400 °C by contacting with hydrogen for 1 hr and evacuated at temperatures between 400 and 500 °C. Both high evacuation temperatures and reduction at 400 °C during 1 hr produced a sharp decrease in Co° surface concentration. These results are consistent with the catalytic behavior of this perovskite reported earlier by E. A. Lombardo et al. (4–7). A model is proposed to interpret the reduction of LaCoO₃.     

Surface Orientation and Wetting Phenomena in Si/α-Alumina System at 1723 K

Wetting phenomena and the effect of alumina surface orientation on the wettability in Si/α-Al₂O₃ system were studied by an improved sessile drop method using     ,     , C(0001) faces of single crystals and polycrystals at 1723 K in a reducing Ar–3% H₂ atmosphere. The contact angles show a vibration behavior for all the single crystals but to a less extent for the polycrystals. The extent of the vibration correlates not only with the reaction intensity but also with the stability of the Si droplet on the alumina surfaces. The interfacial reaction leads to the formation of a series of reaction rings, which is more serious at the single crystal surfaces. More importantly, the wettability is dependent on the alumina surface orientation, with the intrinsic contact angles being about 98±2°, 101±1°, 69±1°, and 98±2°, respectively, for the     ,     , C(0001) and polycrystal α-Al₂O₃ substrates. The much smaller contact angle for molten Si on the C(0001) surface is explained by the favorable reduction in the Si/α-Al₂O₃ interfacial free energy by the terminated and enriched aluminum atoms at the reconstructed     surface. The importance of the aluminum presence at the Si/α-Al₂O₃ interface to the wettability of this system was further demonstrated by a substantial improvement in the wettability of the     α-Al₂O₃ substrates by Si–Al alloys.     

Carbon-13 NMR spectroscopic analysis of 24-methyl-Δ5,22-sterols in rape and mustard seed oils

24-Methylcholesta-5,E-22-dien-3β-ol (C₂₈ Δ^5,22-sterol) was separated from the unsaponifiable matters of the following eight seed oils of Brassica species:Brassica campestris (candle I and II and torch),B. napus (tower and midas),B. juncea (brown and oriental mustards), andB. alba (yellow mustard). The configuration at C-24 methyl group of the respective sterols was evaluated by¹³C NMR spectroscopy. All the C₂₈ Δ^5,22-sterols in the Brassica seed oils were found to contain the C-24 epimer of brassicasterol,trans-22-dehydrocampesterol, in the range of ca. 10–30%.