STRUCTURE FORMATION OF COATED FILMS WITH DISPERSED PIGMENTS DURING DRYING

In the drying of coated films with dispersed pigments, such as floppy disks, the structure of the film is formed during the drying process and depends on the drying condition. It is important to understand the structure formation during drying for the design of the dryer and die better quality of the product. We measured die drying characteristics of the film and determined the structure of dried film experimentally. A qualitative model for the structure formation during drying of the coated film is suggested.     

The structure and maximal gain of CW-pumped GaP-AlGaP semiconductor Raman amplifier with tapers on both sides

GaP-AlGaP waveguide semiconductor Raman amplifiers (SRAs) tapered on both sides were fabricated by high-quality GaP-AlGaP liquid phase epitaxial growth using the temperature difference method with controlled vapor pressure (TDM-CVP), photolithography patterning, and reactive ion etching with PCl/sub 3/ gas. Although the finesse of the both-sides-tapered waveguide SRA is lower than previous values for straight or one-side-tapered waveguides, the CW-pumped gain was maximized, and a maximal gain of 4.2 dB was obtained. This letter presents the effect of tapered structures in SRA with CW pumping amplification.     

Characterization of temporal response, spectral responsivity and its spatial uniformity in photoconductive diamond detectors

Three photoconductive diamond detectors with highly oriented diamond (HOD) films fabricated by the same process were characterized with respect to temporal response, spectral responsivity and its spatial uniformity over the wavelength range from 190 to 250 nm. Temporal measurements showed a drift in the baseline, suggesting the presence of deep level carrier traps. The responsivity of specimen No. 2 was more than twice those of the other two specimens, but it showed an unpredictable current fluctuation. It was found that the spatial uniformities of all the specimens were too low for radiometric purposes. A prominent peak, thought to be due to photoemission, was found in the responsivity spatial distribution of specimen No. 3 under a negative applied voltage.     

High-performance polymer alloys of polybenzoxazine and bismaleimide

Two series of high-performance polymer alloys were prepared by mixing typical benzoxine monomers, 3-phenyl-3,4-dihydro-2H-1,3-benzoxazine (P-a) or 6,6-(1-methylethyliden)-bis-(3,4-dihydro-3-phenyl-2H-1,3-benzoxazine) (B-a), with a typical bismaleimide, 4,4-bismaleimidodiphenyl methane by various ratios followed by thermal treatment up to 240 °C. DSC and IR of the alloys were examined to follow the curing reaction. These analyses showed that the obtained polymer alloys are AB co-cross-linked polymer networks through the formation of ether linkage between the hydroxyl group of polybenoxazine and the double bond of bismaleimide. Viscoelastic analysis and softening temperature measurement revealed that the polymer alloys have much higher glass transition temperatures than those of each homopolymer. The thermal stability also increased with the increase of bismaleimide content as evidenced by TGA.     

Young’s modulus of crystalline C60 nanotubes studied by in situ transmission electron microscopy

Bending tests of crystalline nanotubes composed of fullerene C₆₀ molecules are performed inside a high-resolution transmission electron microscope. We fixed one side of a C₆₀ nanotube with a body-centered tetragonal structure with typical inner and outer diameters, i.e., 180 nm and 510 nm, respectively, and then applied concentrated forces on the other side using piezomanipulation of a silicon nanotip. The bending process was observed in situ by transmission electron microscopy with simultaneous measurements of the forces by an optical deflection method. It was found that the Young’s modulus of the nanotube was estimated to be 62–107 GPa, which was 1.1–3.3 times larger than that of C₆₀ nanowhiskers. The result concerning the increase in the Young’s modulus of the C₆₀ nanotube provided an experimental evidence for the structural model composed of an inner core and a surface shell for C₆₀ nanowhiskers.     

Creep Crack Growth in Polypropylene Film with Various Crack Lengths at Diverse Stresses and Temperatures

Creep crack growth rates were measured using centrally cracked tension specimens of thin polypropylene film with different crack lengths at various stresses and temperatures. The creep crack growth rates were correlated with the stress intensity factor. There was the region of the minimum constant crack growth rate which occupied more than 70% of the total creep failure life. This constant creep crack growth rate characteristics were analyzed on the basis of the stress-dependent Arrhenius type thermally activated process.     

Heat Generation in Multilayer Piezoelectric Actuators

Multilayer piezoelectric actuators when driven under high frequency, generate significant heat, which influences the reliability and other piezoelectric properties. In this paper, heat generation in various types of multilayer PZT-based actuators was studied. Experimental results showed that heat generation is mainly caused by ferroelectric hysteresis loss in the stress-free state. A simplified analytic method was established to evaluate the temperature rise, which is useful for the design of multilayer and other high-power actuators.     

Temporal integration method for image-processing-basedsuper-high-resolution image acquisition

The authors propose an image processing-based approach towards the development of a super-high-resolution image acquisition system. Imaging methods based on this approach can be classified into two main categories: a spatial integration imaging method and a temporal integration imaging method. With regard to the spatial integration imaging method, the authors have previously presented a method for acquiring an improved-resolution image by integrating multiple images taken simultaneously with multiple different cameras. They develop their work, aiming at a particular class of application where a user indicates a region of interest (ROI) on an observed image in advance, and apply a prototypal temporal integration imaging method. The prototypal temporal integration imaging method does not involve global image segmentation, but uses a subpixel registration algorithm which describes an image warp within the ROI, with subpixel accuracy, as a deformation of quadrilateral patches. The method then performs a subpixel registration by warping an observed image with the warping function recovered from the deformed quadrilateral patches. Experimental simulations demonstrate that the temporal integration imaging is promising as a basic means of high resolution imaging     

Spontaneous hemorrhage of an adrenal cortical adenoma causing Cushing''s syndrome

A modified surgical splint for Le Fort I osteotomies with transverse expansion is presented. The splint is made of a transpalatal stainless steel bar with acrylic abutment against the palatal surface of the molar and bicuspid tooth. It is rigid and renders excellent retention. It causes minimal patient discomfort, and oral hygiene is hardly compromised.