Effect of Grain Boundaries on Thermal Conductivity of Silicon Carbide Ceramic at 5 to 1300 K

The thermal conductivity of a SiC ceramic was measured as 270 W·m⁻¹·K⁻¹ at room temperature. At low temperatures ( T < 25 K), the decrease in the conductivity was proportional to T ³ on a logarithmic scale, which indicated that the conductivity was controlled by boundaries. The calculated phonon mean free path in the ceramic increased with decreased temperature, but was limited to ∼4 μm, a length almost equal to the grain size, at temperatures below 30 K. We concluded that the thermal conductivity of the ceramic below 30 K was influenced significantly by grain boundaries and grain junctions.     

Effects of 6-anilino-1,3,5-triazine-2,4-dithiol,zinc stearate,and barium stearate on the thermal stabilization of PVC

Individual action and synergistic effect in the combination of 6-anilino-1,3,5-triazine-2,4-dithiol (AF), zinc stearate, and barium stearate on the color stabilization of PVC were investigated. In this system, AF selectively reacts with allylic chlorine atoms in PVC. Consequently, unstable allylic chlorine units were converted to thermally stable allylic structures, thus retarding the development of polyene sequences. Zinc stearate accelerated the reaction of AF with allylic chlorine atoms in PVC, forming the zinc salts of AF (AFZ_nSt, St?C₁–H₃₅COO? ) by reacting with AF. Barium stearate reacted with ZnCl₂ which is formed in the above reaction to give St₂Zn and BaCl₂. Consequently, barium stearate led to the selective reaction of AF with allylic chlorine atoms in PVC and the remarkable retarding effect of discoloration of PVC.     

Polymerization of 2-dibutylamino-1,3,5-triazine-4,6-dithiol on wire during friction process

2-Dibutylamino-1,3,5-triazine-4,6-dithiol (DB) and a mixture of DB and triallylisocyanurate (TAIC) were used as a lubricant during steel wire drawing due to a dry process. DB gave a polymer film with 180 nm in thickness to wire surfaces during the wire drawing. The polymer film had a disulfide structure on the backbone and contained a small amount of DB monomer and olygomer. Molecular weight and polymer weight increased with the drawing rate. The mixture of DB and TAIC gave mainly a three-dimensional polymer film with 225 nm in thickness to wire surfaces during drawing. The polymer film insoluble in THF had mono and disulfide structures and contained a small amount of linear polymer, DB, and TAIC. Such tribological polymerizations are estimated as follows: DB produces dithiyl radicals on a nascent surface formed during drawing and in the presence of oxygen and heat. The dithiyl radicals were polymerized by coupling with each other to give disulfide bonds or added to allyl groups in TAIC to give monosulfide bonds. It is concluded that this technique should be possible to use for unifying metal processing and surface treatment. © 1995 John Wiley & Sons, Inc.     

Halogen-free acylation of toluene over FeSBA-1 molecular sieves

Three-dimensional cage type iron substituted mesoporous silica with different iron contents (FeSBA-1) was synthesized in a highly acidic media using cetyltriethylammonium bromide and tetraethylorthosilicate as a template and a silica source, respectively. Acylation of toluene with acetic anhydride (AA) was carried out over FeSBA-1 mesoporous catalysts with different n_Si/n_Fe ratios in the temperature range 80–180 °C for a time-on-stream of 1–6 h under liquid phase conditions. The important factors affecting the conversion and the selectivity of the reaction, such as the reaction temperature, feed ratio, catalyst weight and time-on-stream were studied and the results are discussed in detail. The reaction conditions were optimized and the n_AA/n_Toluene ratio of 2 and catalyst weight of 0.1 g (3.3 wt% of total reaction mixture) were maintained for all catalytic runs. It was found that the catalytic activity is strongly influenced by the amount of tetrahedral iron in the catalysts. Among the catalysts used in the present study, FeSBA-1(36) showed a high toluene conversion and selectivity to p-methylacetophenone (p-MAP) under the optimized reaction conditions. It was also found that the selectivity for p-MAP was always higher than m-MAP and o-MAP for all the catalysts and the activity of the catalysts changes in the following order: FeSBA-1(36) > FeSBA-1(90) > FeSBA-1(120).     

Development of flexible organic light‐emitting diode on barrier film and roll‐to‐roll manufacturing

To come out with a successful organic light‐emitting diode (OLED) lighting business, it is very important to have clear differentiation of OLED from LEDs. Flexible OLED has merits, such as capability to be mounted on the curved wall, which is not easy for LEDs to achieve the feature. There are several approaches to make flexible OLEDs especially among those plastic barrier films that can bring high level of flexibility, which could not be achieved by any conventional lighting method. In this paper, barrier films with various water vapor transmission rate values, including 10^{? 6} order, are applied, and the conditions to have almost no dark spot growth under 85 °C and 85% high temperature/humidity test are shown. Flexible OLED panels are manufactured with the world's first roll‐to‐roll equipment using plastic barrier film.     

Characterization and Sintering Behavior of Alkoxide-Derived Aluminosilicate Powders

Submicrometer SiO₂-Al₂O₃ powders with compositions of 46.5 to 76.6 wt% Al₂O₃ were prepared by hydrolysis of mixed alkoxides. Phase change, mullite composition, and particle size of powders with heating were analyzed by DTA, XRD, IR, BET, and TEM. As-produced amorphous powders partially transformed to mullite and Al-Si spinel at around 980°C. The compositions of mullite produced at 1400° and 1550°C were richer in Al₂O₃ than the compositions of stable mullite solid solutions predicted from the phase diagram of the SiO₂-Al₂O₃ system. Particle size decreased with increasing Al₂O₃ content. The sintered densities depended upon the amount of SiO₂-rich glassy phase formed during sintering and the green density expressed as a function of particle size.     

Fabrication of Transparent, Sintered Sc2O3 Ceramics

We report here the fabrication of transparent Sc₂O₃ ceramics via vacuum sintering. The starting Sc₂O₃ powders are pyrolyzed from a basic sulfate precursor (Sc(OH)_2.6(SO₄)_0.2·H₂O) precipitated from scandium sulfate solution with hexamethylenetetramine as the precipitant. Thermal decomposition behavior of the precursor is studied via differential thermal analysis/thermogravimetry, Fourier transform infrared spectroscopy, X-ray diffractometry, and elemental analysis. Sinterability of the Sc₂O₃ powders is studied via dilatometry. Microstructure evolution of the ceramic during sintering is investigated via field emission scanning electron microscopy. The best calcination temperature for the precursor is 1100°C, at which the resultant Sc₂O₃ powder is ultrafine (∼85 nm), well dispersed, and almost free from residual sulfur contamination. With this reactive powder, transparent Sc₂O₃ ceramics having an average grain size of ∼9 μm and showing a visible wavelength transmittance of ∼60–62% (∼76% of that of Sc₂O₃ single crystal) have been fabricated via vacuum sintering at a relatively low temperature of 1700°C for 4 h.     

Heat transfer to laminar flow with temperature — dependent heat generation

Two problems were solved theoretically on the heat transfer to circular tube flow with internal heat source. The one problem is to maintain the mixed-mean temperature of fluid at the inlet temperature. The other is a conjugated problem with a uniformly specified temperature at the outside surface of the wall, accounting for the wall conduction. From the numerical example for the former, it is shown that the mixed-mean temperature can be controlled within 15% error under the estimated condition. From the numerical results for the latter, it is concluded that the influence of wall conduction is more serious than the case without heat generation.     

Effect of platelet-activating factor on lipoprotein lipase and blood lipids

We investigated the effect of platelet-activating factor (PAF) and of the PAF specific antagonist CV-6209 on plasma lipid metabolism, and particularly on post-heparin plasma lipolytic activity in male Wistar rats. Lipoprotein lipase (LPL) activity was enhanced by intravenous injection of PAF before intravenous injection of heparin when the PAF dose was low (0.2 μg/kg). PAF activated hepatic triacylglycerol lipase (HTGL) activity dose-dependently. Plasma triacylglycerols (TG) significantly decreased with the activation of LPL and/or HTGL. Plasma total cholesterol (TC) and phospholipid (PL) levels decreased at a low dose of PAF (0.2 μg/kg), but increased when higher doses were used. The PAF antagonist CV-6209 partially reversed the PAF induced effects on HTGL, TC and PL. Based on a paper presented at the Third International Conference on Platelet-Activating Factor and Structurally Related Alkyl Ether Lipids, Tokyo, Japan, May 1989.     

One-step formation of ethyl methyl ketone from 1-butene and water on ultrastable Y-type zeolite catalyst

Proton exchanged ultrastable Y-type zeolite with silica/alumina = 40 showed a pronounced catalytic activity for the formation of ethyl methyl ketone directly from 1-butene and water. The formation rate of ethyl methyl ketone was much higher than those on MoO₃-based catalysts in the oxidation of 1-butene by oxygen. It was suggested that the basic site necessary for the formation of ethyl ketone directly from 1-butene and water would be the pentacoordinated Al.