Pressureless sintering and characterization of cordierite/ZrO2 composites

Cordierite/ZrO₂ composites with 5 to 25 wt% ZrO₂ were fabricated by conventional powder mixing and pressureless sintering method. Their densification behavior, microstructure, mechanical and thermal properties were studied. By dispersing 25 wt% (9.57 vol%) ZrO₂, densified cordierite/ZrO₂ composite with a relative density of 98.5% was obtained at an optimum sintering condition of 1440 °C and 2 h. ZrO₂ particles were homogenously dispersed within matrix grains and at the grain boundaries. The intragranular particles were finer than 100 nm and the intergranular particles were coarser. Both fracture strength and toughness could be enhanced more than two times higher, compare to those of monolithic cordierite, by dispersing 25 wt% ZrO₂ into the cordierite matrix. The toughening mechanism in the present composites was mainly attributed to martensitic transformation due to ZrO₂ dispersion. Electronic Publication     

Silica removal from Mokai, New Zealand, geothermal brine by treatment with lime and a cationic precipitant

Preliminary experiments using two chemicals (CaO, a quicklime, and a cationic nitrogen-bearing precipitant, EC-004) to remove silica from geothermal brine were undertaken at the Mokai geothermal plant, New Zealand. The brine was mixed with the reagent (CaO or EC-004). The reaction was studied from the start of the experiment (NRT, 0 min, no retaining time) and after 15 min (15RT) at 90 °C. The concentration of silica in the brine was initially 954 mg/l, and decreased linearly with increasing reagent concentration. When CaO is added, the silica concentration at 15RT was 200 mg/l lower than at NRT and became almost zero on addition of 1.5 g/l. In contrast, when EC-004 is added, the total silica concentration nearly reaches the solubility of amorphous silica at 90 °C. In order to prevent silica scaling in Mokai brines cooled to 90 °C, the CaO and EC-004 added should be individually adjusted to 0.5 g/l and 80 mg/l, respectively.     

Extended AB Period Study of the Electron Pairing Transition int-J Ladders

The extended Aharonov-Bohm period test, recently proposed by the present authors, is used to study the electron pairing transition in the t-J ladders. The critical point is detected as a gap opening in the extended spectral flow. The result suggests a pairing prior to the onset of a phase separation, which is consistent with a recent Tomonaga-Luttinger analysis.     

Strength and ductility under dynamic loading in fine- grained IN905XL aluminum alloy

Three IN905XL aluminum alloys with fine grain (1 μm), intermediate grain (3 μm), and coarse grain (5 μm) have been developed by a combination of mechanical alloying (MA) and conventional extrusion in order to investigate their mechanical properties at dynamic strain rates of 1 × 10³ and 2 × 10³ s⁻¹ and a quasi-static strain rate of 10^-3 s⁻¹. Flow stresses are found to increase with decreasing grain size for all the strain rates tested. Negative strain-rate sensitivity of flow stress is observed up to 1 × 10³ s⁻¹ in both intermediate- and coarse-grained IN905XL. At the highest strain rate of 2 × 10³ s⁻¹ however, all samples showed a positive strain-rate sensitivity of strength. Total elongation at high strain rates is generally larger than that at low strain rates. Total elongation also decreases with grain size for all the strain rates. This decrease in elongation results from an initiation of microcracks at interfaces between the matrix and particles finely dispersed near grain boundary regions, introduced during MA processing; then, this initiation leads elongation of alloys to small limited values. Formerly with the Department of Mechanical Systems Engineering, University of Osaka Prefecture. This article is based on a presentation made in the symposium “Dynamic Behavior of Materials,” presented at the 1994 Fall Meeting of TMS/ASM in Rosemont, Illinois, October 3-5, 1994, under the auspices of the TMS-SMD Mechanical Metallurgy Committee and the ASM-MSD Flow and Fracture Committee.     

波形测量技术的发展趋势--兼谈YOKOGAWADE的示波器发展

本文着重论述了波形测量技术的最新发展趋势。     

Surface Hardening of Carbon Steel Using High Powered YAG Laser

A high powered YAG laser with kaleidoscope for surface modification was applied to the surface hardening of carbon steels containing 0. 18-0.54 wt% C without the absorbents, and the relationships between laser processing and surface hardening were investigated by hardness and microstructure. The structure of the hardened zone underwent complete martensitic transformation in all of the carbon steels tested, and its hardness increased with greater carbon content. Under identical irradiated conditions, the hardened zone expanded with increasing carbon content. A hardened zone extending from the surface to a depth of 1.0 mm was obtained at a laser power of 1.0 kW and a scanning speed of 1 mm/sec. It was found that in the surface hardening of carbon steels, a high powered YAG laser can be used to control the hardened zone by selecting the appropriate irradiation conditions, however, the hardened zone was affected by the assistant gas and the flow rate.     

Far-Infrared Reflection Spectra of Dielectric Ceramics for Microwave Applications

Far-infrared reflection spectra of dielectric ceramics, BaSm₂Ti₅O₁₄, BaTi₄O₉, and some pcrovskites such as Ba(Zn_1/3Nb_2/3)O₃, have been measured at room temperature using a Fourier transform infrared spectrometer in order to investigate the effect of the crystal structure on the dielectric properties. As for perovskites, Sr(Zn_1/3Nb_2/3)O₃ and Sr(Mg_1/3Nb_2/3)O₃, in which B site ions are ordered, were also measured. Reflectance data were analyzed by means of a factorized form of dielectric functions instead of the classical dispersion theory, and all of the spectra were well fitted. The values of dielectric constants and tan δ calculated from the reflectance data were in good agreement with resonant cavity measurements at 5 GHz. Furthermore, results of this study have shown that the main contribution to the microwave dielectric properties is caused by low-frequency optically active modes located at 50 to about 300 cm⁻¹, and for perovskite structures it is suggested that the ordering of B site ions is significant in obtaining low dielectric losses.     

A novel tungsten light-shield structure for high-density CCD imagesensors

A novel tungsten light-shield structure has been developed. Tungsten film properties, the device configuration with the tungsten light-shield structure, and experimentally achieved results regarding device characteristics are described. Optical measurement clarified that tungsten film has a sufficiently low transmittance value for practical use for more than 200-nm-thick film and is stable up to 1000°C. The good step coverage and low reflectance, such as 20-40% for aluminum, required for light-shield film were also obtained. A tungsten light-shield structure was applied to a 1/2-in format 668(H)-pixel×575(V)-pixel charge coupled-device (CCD) image sensor. An extremely low smear value, less than 0.001%, was obtained for a 300-nm film thickness     

Microstructural change of ultrafine-grained aluminum during high-speed plastic deformation

Effect of strain rate on microstructural change in deformation of the ultrafine grained (UFG) aluminum produced by severe plastic deformation (SPD) was studied. Commercial purity 1100 aluminum sheets were highly strained up to an equivalent strain of 4.8 by the Accumulative Roll-Bonding (ARB) process at ambient temperature. The ARB-processed sheets were found to be filled with pancake-shaped ultrafine grains surrounded by high-angle grain boundaries. The ultrafine grains had a mean grain thickness of 200 nm and a mean grain length of 1100 nm. The ultrafine-grained aluminum sheets were deformed at various strain rates ranging from 2 to 6.0×10⁴ s⁻¹ by conventional rolling, ultra-high-speed rolling, and impact compression. High-speed plastic deformation generates a large amount of heat, inducing coarsening of the ultrafine grains during and after deformation. On the other hand, it was also suggested that high-speed plastic deformation is effective for grain-subdivision, in other words, ultra-grain refinement, if the effect of heat generation is extracted.     

Molecular cloning and characterization of rat lin-10

In Caenorhabditis elegans, the vulval induction is mediated by tyrosine kinase receptor/Ras signal transduction pathway composed of the lin-3, let-23, and let-60 products. In addition to these gene products, the lin-2, lin-7, and lin-10 products are also implicated in this pathway. Lin-2 encodes a MAGUK and lin-7 encodes a small protein with one PDZ domain. The lin-10 product has no homology to known proteins. Here, we have cloned a rat homologue of the lin-10 product and characterized it. Rat lin-10 is ubiquitously expressed in various rat tissues and distributed in both the cytosol and membrane fractions. In brain, however, rat lin-10 is distributed only in the membrane fraction and enriched in the synaptic plasma membrane and postsynaptic density fractions. These results suggest that rat lin-10 is involved at least in synaptic functions in brain.