Design optimization of tall tubular lead/acid cells based on an analysis of the reaction distribution

In order to estimate the discharge performance of tall lead/acid cells (with tubular positives), changes in current and potential distributions with discharge progress were calculated with a computer on the basis of plate resistance and the current—potential—time relationship between small facing parts of positive and negative plates. The taller the cell, the larger the voltage drop along the plates. Thus, the discharge time became shorter despite a large amount of available active mass remaining in the bottom part of the plates.Various current-collector designs were evaluated, e.g., one with varying resistance at each height; a side conductor placed along the plates and connected to them at the top, centre and bottom, etc. Results revealed an optimum collector design with which the maximum discharge capacity could be obtained. Furthermore, it was shown that the side conductor markedly improved the discharge performance because the active mass near the connecting parts was appreciably used.     

Development of a fast neutron radiography converter using wavelength-shifting fibers

A fluorescent converter for fast neutron radiography (FNR) comprising a scintillator and hydrogen-rich resin has been developed and applied to electronic imaging. The rate of the reaction between fast neutrons and the converter is increased by thickening the converter, but its opaqueness attenuates emitted light photons before they reach its surface. To improve the luminosity of a fluorescent converter for FNR, a novel type of converter was designed in which wavelength-shifting fibers were adopted to transport radiated light to the observation end face. The performance of the converter was compared with that of a polypropylene-based fluorescent converter in an experiment conducted at the fast-neutron-source reactor YAYOI in the University of Tokyo.     

Effects of cononsolvency on gelation of poly(vinyl alcohol) in mixed solvents of dimethyl sulfoxide and water

We studied the rates of gelation and phase separation of poly(vinyl alcohol) (PVA) solutions in mixtures of dimethyl sulfoxide (DMSO) and water at 25 °C and found that both the rates show a maximum at a volume fraction of DMSO φ_DMSO=0.60 while gelation was not observed either in pure DMSO or pure water, suggesting that water-DMSO is a cononsolvent system for PVA. On the basis of the data by Cowie [Can J Chem 36 (1961) 2240] we concluded that the 1:2 stable complex between one DMSO molecule and two water molecules is the main cause of this cononsolvency.     

X-ray Photoelectron Spectroscopy Investigation on the Low-Temperature Degradation of 2 mol% Y2O3-ZrO2 Ceramics

2 mol% Y₂O₃-ZrO₂ polycrystals were annealed in water and under vacuum to highlight the effect of the presence of H₂O on the low-temperature degradation transformation. The specimen surfaces with monoclinic phases transformed during annealing in the different environments were analyzed by X-ray photoelectron spectroscopy with special interest on the electron binding energy change of the constituent ions of the 2 mol% Y₂O₃-ZrO₂ ceramics after the degradation transformation. It was found that no change occurred for the electron-bonding energies of core levels of zirconium ions after the transformation, whereas Y-OH bonds were formed during annealing in water. This result suggested a possibility that the preferred hydration of yttrium took place at the surface of Y₂O₃-partially-stabilized ZrO₂, which is likely to be the reason for the low-temperature degradation accelerated by the presence of H₂O.     

Discharge behaviour of electrodeposited PbO2 and Pb electrodes

The discharge behaviour of electrodeposited lead dioxide and lead electrodes was investigated under various conditions; the surfaces of the discharged electrodes were observed with a scanning electron microscope. Both the positive and negative electrodes were passivated by a covering of deposited lead sulphate crystals. The amount of lead sulphate required for passivation depended on the size of the crystals.     

Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

Thermal expansion behavior of various aromatic polyimides

The thermal expansion behavior for various aromatic polymides was investigated. Usally polymers, including polyimides, have high thermal expansion coefficients (3–6 × 10^?5 K^?1), compared with metals and ceramics. However, there are some polyimides which have very low thermal expansion coefficients below 1 × 10^?5 K^?1. This property was observed for the polymides obtained from pyromellitic dianhydride or 3,3′ 4,4′-biphenyltetracarboxylic dianhydride and aromatic diamines which were constituted of only benzene rings fused at para positions. It was proposed that their low thermal expansion coefficient related to the linearity in their polymer molecular skeltons.     

Development of a dual‐lamp projector with higher brightness

Stationary projectors mainly used in system applications have recently gained a wider application range, including general presentations in halls and large conference rooms and being used, for example, in digital signage and for monitoring purposes. Consequently, they are required to meet new market demands for durability, reliability, and flexibility in installation in addition to their conventional basic performance such as especially high brightness. To achieve especially high brightness, a new optical system with two lamps is proposed; the profile of the cover glass that prevents the glass from scattering is made aspherical, the profile of the beam‐combining mirror is improved with its position optimized, and the size of the incident plane of the integrator rod is made larger (1.1 times). These measures resulted in an optical system of an even higher efficiency with 7000 lm, which is the highest in its class (according to a June 2010 investigation). Also, the arrangement of two parallel lamps completely eliminated the effect of heat passing from one lamp to the other, which helped secure durability, reliability, and flexibility in installation. Furthermore, the combined use of the unique non‐telecentric optical system, adopted from the conventional single‐lamp model, helps maintain the class‐highest contrast ratio.^1,2     

Humidity Sensor Characteristics of Woodceramics

The humidity sensor characteristics of Woodceramics were investigated. The Woodceramics used in this experiment were prepared at 650–900°C. The size of specimens selected was 1 × 1 × 10 mm . One was used as-cut and the other was polished. Above 700°C, the resistance of the specimen was below 50 and the decrease of resistance with increasing relative humidity was small. The specimen prepared at 650°C had a resistance of about 1 k. The resistance of as-cut specimens decreased with increase in relative humidity, but that of the polished specimen did not change significantly. The difference between as-cut and polished samples was explained by the differences in surface micro-structure.